Daewoo DTB-F071LH-DVI User manual

1
Service Manual
Split System Air
Conditioner
Model: DTB-F071LH-DVI
DTB-F091LH-DVI
DTB-F121LH-DVI
DTB-F181LH-DVI
DMB-F2713LH-AVO
DAEWOO ELECTRONICS CO., LTD.
by Nemko
S/M NO. :DTBF071001

CONTENTS
1. Features
2. Specification
3. Outline and dimension
4. Indoor unit combination
5. Capacity table
6. Wiring diagram
7. Electronic control functions

1. Features:
1) Fashion design, quality life;
2) Low operation noise;
3) High efficiency screw fan;
4) Equal, fast, wide-angle cooling, more comfortable.

2.Specification
indoor unit Model MSQ4I-07HRIN1 MSQ4I-09HRIN1 MSQ4I-12HRIN1 MSQ4I-18HRIN1
Power supply Ph-V-Hz 1Ph,220-240V~,50Hz 1Ph,220-240V~,50Hz 1Ph,220-240V~,50Hz 1Ph,220-240V~,50Hz
Cooling Capacity BTU/h 7,000 9,000 12,000 18,000
Heating Capacity BTU/h 8,500 11,000 14,000 21,000
Design Pressure (Hi/Lo) Mpa 4.2/2.5 4.2/2.5 4.2/2.5 4.2/2.5
Capacity
Max. Operating Pressure Mpa 3.5 3.5 3.5 3.5
Model YDK45-4F YDK45-4F YDK45-4F YDK45-4F
Brand Welling Welling Welling Welling
Power Input W63 63 63 63
Capacitor uF 1.5uF/450V 1.5uF/450V 1.5uF/450V 2.5uF/450V
Indoor fan motor
Speed(hi/mi/lo) r/min 750/660/540 750/660/540 830/730/680 930/830/660
a.Number of rows 2 2 2 2
b.Tube pitch(a)x row pitch(b) mm 21x13.37 21x13.37 21x13.37 21x13.37
c.Fin spacing mm 1.3 1.3 1.3 1.3
d.Fin type (code) Hydrophilic aluminium Hydrophilic aluminium Hydrophilic aluminium Hydrophilic aluminium
e.Tube outside dia.and type mm Ф7.94, innergroove
tube
Ф7.94, innergroove
tube
Ф7.94, innergroove
tube
Ф7.94, innergroove
tube
f.Coil length x height x width mm 1185X210X26.7 1185X210X26.7 1185X210X26.7 1185X210X26.7
Indoor coil
g.Number of circuits 5 5 5 5
Indoor air flow (Hi/Mi/Lo) m3/h 600/500/420 600/500/420 680/580/500 860/760/650
Indoor noise level (Hi/Mi/Lo) dB(A) 36/33/30 36/33/30 36/33/30 43/40/38
Pipe size Liquid side/ Gas side mm(inch) φ6.35 (1/4’)
φ9.53 (3/8’)
φ6.35 (1/4’)
φ9.53 (3/8’)
φ6.35 (1/4’)
φ12.7 (1/2’)
φ6.35 (1/4’)
φ12.7 (1/2’)
Dimension (W*H*D) mm 580×254×580 580×254×580 580×254×580 580×254×580
Packing (W*H*D) mm 750x340×750 750x340×750 750x340×750 750x340×750
Indoor
unit(body) Net/Gross weight(body) Kg 21/28 21/28 21/28 28/36

Dimension (W*H*D) mm 650x30x650 650x30x650 650x30x650 650x30x650
Packing (W*H*D) mm 715x115x715 715x115x715 715x115x715 715x115x715
Indoor
unit(panel) Net/Gross weight(panel) Kg 3/5 3/5 3/5 3/5
Application area m210-14 14-21 18-26 35-40
Qty per 20’/40’/40’HQ Pieces

OUTDOOR UNIT:
Outdoor Model M4OA-27HRIN1
Indoor unit combination single double Treble Quadplex
Power supply Ph-V-Hz 1Ph,220-240V~,50Hz
Cooling Capacity range Btu/h 7000~18000 14000~24000 21000~27000 27000
Rated input power range W960~2510 1450~2830 2050~3100 3141 Cooling
Rated current range A 4.4~12.0 6.6~13.0 9.4~14.5 14.8
Heating Capacity range Btu/h 9000~18000 16000~27000 21000~30000 32000
Rated input power range W1100~2430 1400~2520 2020~2950 2982
Heating
Rated current range A 5.0~11.6 6.4~12.0 9.3~13.8 13.9
Max. input consumption W4500
Max. current A25
Model BA160X2CS-20KU
Type Rotary inverter
Brand GD Toshiba
Capacity Btu/h 18000(60HZ)
Input W1690（60HZ）
Rated current(RLA) A11.6（60HZ）
Locked rotor Amp(LRA) A60
Thermal protector Internal
Capacitor uF 85UF/250V
Compressor
Refrigerant oil ml RB68AF/α68TF/T-68 750 ml
Model YDK100-6
Brand Welling
Input W169(HIGH)
Capacitor uF 5uF/500VAC
Outdoor fan
motor
Speed r/min 900(HIGH)

a.Number of rows 2
b.Tube pitch(a)x row pitch(b) mm 25.4×22
c.Fin spacing mm 1.5
d.Fin type (code) Hydrophilic aluminium
e.Tube outside dia.and type mm φ9.53 innergroove tube
f.Coil length x height x width mm 850×810×44
Outdoor coil
g.Number of circuits 2
Outdoor air flow m3/h 3500
Outdoor noise level dB(A) 57
Dimension(W*H*D) mm 895X860X330
Packing (W*H*D) mm 1043X915X395
Outdoor unit
Net/Gross weight Kg 80/84
Refrigerant type and charge gR410A, 2700
Design pressure(Hi/Lo) MPa 4.2/2.5
Liquid side/ Gas side mm(inch) 6.35(1/4)/9.53(3/8)
Max. refrigerant pipe length for
each unit m20
Refrigerant
piping
Max. difference in level between
indoor and outdoor unit m10
Connection wiring No
Plug type No
Thermostat type Electronic control
Cooling ℃18~45
Operation temp heating ℃-15~33
Qty’per 20’ /40’ /40'HQ set
Notes:
1. Nominal cooling capacities are based on the following conditions:
Indoor temp: 27°CDB, 19°CWB;

Outdoor temp: 35°CDB;
Equivalent ref. Piping: 8m(horizontal)
2. Nominal heating capacities are based on the following conditions:
Indoor temp: 20°CDB;
Outdoor temp: 7°CDB, 6°CWB;
Equivalent ref. Piping: 8m(horizontal)
8. Actual noise level may differ, depending on the room structure, etc, since these noise values are from an anechoic room.

3.Outline and dimension
Indoor unit(7k/9k/12k/18k):
580(Body) 67
600(Ceiling hole)
650(Panel)
401(Hook-location)
611(Hook-location)
580(Body)
422 28.5
600(Ceiling hole)
650(Panel)
Drain side and Tubing side
A
600
Hook
265
Panel
Chart 4
Body
Nut
Ceiling
Outdoor unit
1013
590
300
330
355
163 141
895
COMP

4.Indoor unit combination:
Caution on combination
The one-drive-four outdoor unit M4OA-27HRIN1 nominal cooling capacity is 8kw(under
condition of ambient temp. 35℃db/24℃wb, indoor temp. 27℃db/19℃wb). According to
refrigeration design criterion, total indoor unit capacity should be equal to outdoor capacity,
otherwise, we can not guarantee best performance and safe operation. Although, we made
special design on refrigeration system regarding customer’s requirements. Based on this,
when indoor total capacity exceed outdoor capacity, the machine can still run. Under this
condition, the single indoor unit capacity will attenuate. That means you can not gain the
nominal capacity, but smaller than it. We are out of responsibility if customers don’t follow the
notice below:
1. You can connect two, three or four indoor units according your need;
2. The total indoor unit nominal capacity should not exceed 11.3kw(42% more than nominal
capacity);
3. There should be no more one 18k indoor unit(either cassette or duct), and other indoor
unit should be all 7k;
4. There should be no more two duct indoor units, and other indoor units should be all wall
mounted;
5. There should be no more one cassette;
6. Cassette and duct can not be installed simultaneously.
7. When heating, capacity attenuate sharply if indoor unit capacity exceed too much.

5. Capacity table
M4OA-27HRIN1 (7k+7k+7k+7k)
COOLING OUTDOOR TEMPERATURE DRY
Indoor
Conditions 21ºC 25ºC 30ºC 35ºC 40ºC 45ºC
Total capacity kW 7.63 7.30 7.03 6.64 6.37 6.17
Sensitive capacity kW 6.11 5.84 5.63 5.31 5.10 4.94
21ºC D
15ºC W Input kW. 1.95 2.23 2.51 2.79 3.07 3.35
Total capacity kW 8.36 7.99 7.70 7.27 6.98 6.76
Sensitive capacity kW 6.69 6.40 6.16 5.81 5.58 5.41
24ºC D
17ºC W Input kW. 2.06 2.36 2.65 2.95 3.24 3.53
Total capacity kW 9.09 8.69 8.37 7.90 7.58 7.35
Sensitive capacity kW 7.27 6.95 6.70 6.32 6.07 5.88
27ºC D
19ºC W Input kW. 2.17 2.48 2.79 3.10 3.41 3.72
Total capacity kW 10.45 9.99 9.63 9.09 8.72 8.45
Sensitive capacity kW 8.36 7.99 7.70 7.27 6.98 6.76
32ºC D
23ºC W
Input kW. 2.50 2.85 3.21 3.57 3.92 4.28
HEATING OUTDOOR CONDITIONS
Indoor
Conditions 24ºC D
18ºC W 12ºC D 11ºC W 7ºC D 6ºC W 4ºC D 3ºC W 0ºC D -1ºC W -5ºC D -6ºC W -7ºC D -8ºC W -15ºC D -16ºC W
Capacity
kW 14.66 11.73 9.78 8.80 8.31 7.33 6.84 6.35
15ºC
Input kW. 5.52 4.42 3.68 3.50 3.31 3.13 2.94 2.58
Capacity
kW 13.77 11.02 9.18 8.26 7.80 6.89 6.43 5.97
18ºC
Input kW. 5.18 4.15 3.46 3.28 3.11 2.94 2.76 2.42
Capacity
kW 12.75 10.20 8.50 7.65 7.23 6.38 5.95 5.53
20ºC
Input kW. 4.80 3.84 3.20 3.04 2.88 2.72 2.56 2.24
Capacity
kW 11.73 9.38 7.82 7.04 6.65 5.87 5.47 5.08
22ºC
Input kW. 4.42 3.53 2.94 2.80 2.65 2.50 2.36 2.06
Capacity
kW 10.20 8.16 6.80 6.12 5.78 5.10 4.76 4.42
27ºC
Input kW. 3.84 3.07 2.56 2.43 2.30 2.18 2.05 1.79

6. WIRING DIAGRAM
Indoor unit:

Outdoor unit (M4OA-27HRIN1)

7. Electric control functions:
7.1 Protection
1. 3 minutes delay at restart for compressor.
2. Temperature protection of compressor top, compressor stops when the temp. of top of
compressor is more than 120℃, compressor runs when the temp. of top of compressor is less
than 105℃.
3. When AC voltage ≥270V for 30 seconds, Outdoor Unit stops operation and alarms.
When AC voltage ≤260V for 30 seconds, Outdoor Unit resumes operation.
4. Inverter module protection, Inverter module Protection itself has a protection function
against current, voltage and temperature.
5. Sensor protection at open circuit and breaking disconnection.
6. Fan Speed is out of control. When Indoor Fan Speed is too high(higher than High
Fan+300RPM)or too low(lower than 400RPM), the unit stops and LED displays failure
information and can’t return to normal operation automatically.
7. Cross Zero signal error warning. If there is no Cross Zero signals in 4 minutes, the unit
stops and LED displays failure information and can’t return to normal operation automatically.
8. Current protection: When the current is more than 25A, the compressor stops.
9. Outdoor condenser high temperature protection: Under cooling mode, if T3>65 for 3℃
minutes, the compressor will stop. When T3<52 , the protection is not valid.℃
10. Outdoor low temperature protection: If the outdoor temperature is lower than -15 for℃
1hour, the compressor and fan motor will stop. If the outdoor temperature is higher than -12℃
for 10 minutes and the compressor stops operation for 1h, or the outdoor temperature is
higher than 5℃for 10 minutes, then restart and enter into the prior operation mode.
11. Compressor pre-heating function: When the outdoor temperature is lower than 3℃and
the compressor stops operation for more than 3 hours, or the outdoor temperature is lower
than 3℃and the power is just put on, the compressor enters into pre-heating condition. When
outdoor temp. is more than 5℃or user operate it, pre-heating condition will finish.
7.2 Operating mode
7.2.1 Cooling mode
1.Indoor fan keeps running, fan speed can be set in high/mid/low/ Auto:
2.Auto fan at cooling mode: (T=Indoor Temp.-Setting Temp.)
Condition Indoor fan speed
T<1.5℃Low
1.5℃<T<4℃Mid.
Room temp. up
T>4℃High
T> 3℃High
1<T<3℃℃ Mid.
Room temp. down
T<1℃Low
3.Anti-freezing control to indoor evaporator at cooling mode( T: evaporator temp. )
Evaporator Temp. Compressor
T< 4℃Off
T > 8℃On

7.2.2 Dehumidifying mode
1.The indoor fan is fixed in low speed
2. Low room temperature protection:
When room temperature decreases to below 10℃, indoor fan stop, when room temperature
restores to over 12℃, indoor fan start.
3. At dehumidifying mode, the anti-freezing function of the indoor heat exchanger is the same
as that of cooling mode.
7.2.3 Heating mode
1. Indoor Fan actions at heating mode
Indoor Fan can be set at HIGH/MID/LOW/AUTO by using a remote controller, but Anti-cold
wind function prevails.
Anti-cold wind control function at heating mode
Condition
T= Indoor exchanger
temp.
Indoor fan speed
T<34℃Off
34℃<T<37℃Breeze
37℃<T<44℃Low speed
Indoor exchanger temp.
up
T> 44℃Setting fan speed
T> 38℃Setting fan speed
33℃<T<38℃Low speed
24℃<T<33℃Breeze
Indoor exchanger temp.
down
T<24℃Off
1. Auto wind at heating mode
Condition
T=Indoor Temp.-Setting Temp.
Indoor fan speed
T<1.5℃High
1.5℃<T<2.5℃Mid.
Room temp. up
T>2.5℃Low
T<1.0℃High
1.0℃<T<2.0℃Mid.
Room temp. down
T>2.0℃Low
2. Indoor evaporator high-temperature protection at heating mode
Condition
T= Indoor exchanger temp.
Compressor
T<48℃On
53℃<T<63℃Decrease frequency of compressor
T>63℃Off
7.2.4 Defrost operation
1. Defrosting condition:
The temperature of outdoor heat exchanger remains consecutively lower than -2°c for more
than 40 minutes,
2. Ending condition of defrosting

If one of following conditions is satisfied, end the defrost and turn into heating mode:
a. The defrost time has reached to 10 minutes.
b. When the temperature of outdoor heat exchanger rises up to 15°C.
3. Defrosting Actions:
a. Compressor runs.
b. 4 way valve switches off,
c. Outdoor fan switches off
d. Indoor fan running according to anti-cold wind function in heating mode.
4. Automatic operation mode
The air conditioner automatically selects one of the following operation modes: cooling,
heating or fan only according to the temp. difference between room temp. (TA) and set
temp. (TS).
TA—TS Operation mode
TA—TS>2℃Cooling
-1 ≤TA℃-TS≤+2℃Fan-only
TA-TS<-1℃Heating (air-only for cooling only type)
7.3 Mode conflict
The indoor units can not work cooling mode and heating at same time.
Heating mode has a priority.
7.3.1 Definition
Cooling mode Heating Mode Fan Off
Cooling mode No Yes No No
Heating Mode Yes No Yes No
Fan No Yes No No
Off No No No No
No: No mode conflict;
Yes: Mode conflict
7.3.2 In case of one Indoor unit working in cooling mode or fan mode, and another indoor
unit is set to heating mode, the indoor unit working in cooling mode or fan mode will
change to stand by. The outdoor unit will work in heating mode.
7.3.3 In case of one Indoor unit working in heating mode, and another indoor unit is set to
cooling mode or fan mode, the indoor unit setting to cooling mode or fan mode will
change to stand by.
7.4 Manual switch
Mode changes when push this button.
Cooing modeÆAuto modeÆUnit offÆCooing mode
At Cooing mode, after 30 minutes cooling operation whose fan speed is set as low, the
A/C operates with a setting temp. of 24℃.
At auto mode, the A/C operates with a set temp. of 24℃
7.5 Timer Function

1. The maximum length of timer is 24 hours and the minimum resolving power is 15 minutes.
2. Timer on: first turn off the A/C, the A/C will be automatically on at the set time.
3. Timer off: first turn on the A/C, the A/C will be automatically off at the set time
4. Timer on/off function( on time is earlier than off time): first turn off the A/C, it will be
automatically on at set time, and later be off at the set time, then unit turns on at set time.
5. Timer off/on function( off time is earlier than on time): first turn on the A/C, it will be
automatically off at set time, and later be on at the set time, then unit turns off at set time.
7.6 Auto restart function
In case of a sudden power failure, this function automatically sets the unit to previous settings
before the power failure when power returns.
7.7 Cooling capacity test frequency locked.
When test the cooling capacity, the frequency can be locked at 78Hz by following the below:
1. Set the indoor temp. to 17c and high speed;
2. Push the outdoor check button for 5 seconds, then its frequency can be fixed at 78Hz.
After the test is over, turn off the indoor to exit.
7.8 Indoor unit LED display function:
Display Explanation
E0 EEPROM error
E1 Indoor and outdoor communication error
E2 Zero-crossing examination error
E3 Fan speed beyond control
E5 Outdoor units temp. sensor or connector of temp. sensor is defective
E6 Indoor units temp. sensor or connector of temp. sensor is defective
P0 Inverter module protection
P1 Outdoor voltage protection
P2 Compressor top protection against temperature
P3 Compressor current protection
P5 Outdoor low temp. protection

7.9 Outdoor unit LED display function:
1. When stand-by it display number of indoor unit online;
2. When operation it display frequency of outdoor unit;
3. When defrost it display “df”;
4. When a protection or error occurred, it display as the following table:
Display Explanation
E0 EEPROM error
E1 No 1 Indoor units pipe temp. sensor or connector of pipe temp. sensor is defective
E2 No 2 Indoor units pipe temp. sensor or connector of pipe temp. sensor is defective
E3 No 3 Indoor units pipe temp. sensor or connector of pipe temp. sensor is defective
E4 Outdoor temp. sensor or connector of temp. sensor is defective
E5 Compressor voltage protection
E6 No 4 Indoor units pipe temp. sensor or connector of pipe temp. sensor is defective
E7 Indoor and outdoor communication error
P0 Compressor top protection against temperature
P1 High pressure protection
P2 Low pressure protection
P3 Compressor current protection
P4 Inverter module protection
P5 Outdoor low temp. protection
P6 Condenser high-temperature protection
7.10 Check function:
There is a check button on outdoor pcb. When push this button, the outdoor LED can display
in sequence:
Capacity demand→Running mode →revised capacity →fan state →No.1 evaporator pipe
temp. →No.2 evaporator pipe temp.→No.3 evaporator pipe temp.→No.4 evaporator pipe
temp.→outdoor pipe temp. →Outdoor temp. →discharge gas temp.→current of outdoor unit
→No. 1 opening degree of electronic expansion valve →No. 2 opening degree of EXV →
No. 3 opening degree of EXV→No. 4 opening degree of EXV→indoor unit number→last
protection/error code→capacity demand(cycle)
Explanation for the some display content:
1. Running mode:
Display Corresponding mode
0 Off
1 Cooling mode
2 Heating mode

2. Fan state:
Display Corresponding mode
0 Off
1 Low fan
2 High fan
3. Opening degree of EXV:
Opening degree equals the display data times 8;
4. Number of indoor unit
The indoor unit that can communicate with outdoor unit normally.
7.11 Outdoor fan speed control
There is one fan with two-speed, the fan speed is controlled according ambient temp. After
the compressor stop, 30 seconds later the fan stop.
When cooling:
> 27 High speed
Ambient temp.rise <27 Low speed
>25 High speed
Ambient temp.decline <25 Low speed
When heating:
> 14 Low speed
Ambient temp.rise <14 High speed
>12 Low speed
Ambient temp.decline <12 High speed
7.12 Oil return function
If operation frequency is lower than 54Hz in 2 hours consecutively, it will be increased to 62Hz
for 3 minutes. Then it recovers to the former operation frequency.

8. Exploded View