Daewoo POWER BLENDER User manual

SKU 0434822

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed. These instructions should be saved for future
reference:
Read and familiarise yourself with all operating instructions before using
this Blender.
Before plugging your unit into the mains, visually check that it is intact and
has not suffered any transit damage.
Check that the voltage indicates on the data plate corresponds with that of
the local network before connecting the appliance to the mains power
supply.
Do not use this product with a programmer, timer, separate remote-control
system or any other such device.
Do not immerse this appliance in water or any other liquids.
Close supervision is required when using this appliance near children.
Never leave this appliance within reach of children.
This appliance shall not be used by children from 0 to 8 years.
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand
the hazards involved.
Children shall not play with the appliance.
Keep the appliance and its cord out of reach of children less than 8 years.
Cleaning and user maintenance shall not be made by children.
Do not leave the appliance unattended during use.
Do not leave the appliance unattended whilst connected to the mains
supply.
Always use this appliance on a solid, level, non-flammable surface.
Do not use this appliance outdoors.
It is imperative to unplug the power cord after the appliance has been
used, before it is cleaned and whilst being repaired.
Regular, periodic checks should be carried out on the supply cord to
ensure no damage is evident. Should there be any signs of damage the
appliance should not be used.
If the supply cord is damaged it is to be replaced by a qualified person in
order to avoid a hazard.
Do not operate this appliance with a damaged plug or cord, after a
malfunction or after being dropped or damaged in any way.
Do not allow the mains cable to hang over sharp edges or come in contact
with hot surfaces.
Do not use any accessories or attachments with this appliance other than
those supplied or recommended by supplier.
Do not use this appliance for anything other than its intended use.

Do not push objects into any openings as damage to the appliance and/or
electric shock may occur.
CAUTION: The blade assembly is sharp, handle with care. When
handling the blade assembly always hold by the base.
DO NOT ATTEMPT TO SHARPEN THE BLADES
DO NOT use the appliance if the blade assembly is bent or damaged.
To avoid the risk of injury or damage never place the blade assembly onto
the base without the proper attachment.
DO NOT fill the jars past the ‘Max Fill’ mark.
DO NOT operate the appliance whilst it is empty.
This appliance is intended for household use only and should not be used
for industrial or commercial purposes.
Switch off the appliance and disconnect from the supply before changing
accessories or approaching parts that move in use.
Please read these operating instructions thoroughly and keep them in a safe
place for future reference.
Before the first time you use your Blender
Remove all packing materials and dispose of responsibly.
Remove the accessories and wash in warm soapy water, rinse and dry
thoroughly.
Wipe over the motor unit with a damp sponge or cloth.
Do not use harsh or abrasive cleaners.
Do not clean any part of your blender in a dishwasher
Never immerse the motor unit in water or any other liquids.
Do not use the blender to process hot foods or liquids.
WARNING: Do not operate the blender continuously for more than 60
seconds at a time (30 seconds for dry ingredients). Allow 180 seconds rest
time before continuing to blend.
If the blender overheats a thermal switch will activate and shut off the motor.
To reset, unplug the appliance and allow it to cool for 30 minutes before using
again.
NB Add a little water whilst blending fruit and vegetables.
Safety feature
This appliance has a built in safety feature to ensure that the appliance
operates only when the jar and the blade assembly are correctly placed on
the motor unit.

Description of parts
1
2
3
4
5
6
1. Large (0.8 litre) jar 2. Flip top drinking lid
3. Blade Assembly 4. Seal lid (x2)
5. Motor Unit 6. Small (0.5 litre) jar (x2)

Using Your Blender
Place all the ingredients in the
chosen jar; ensure that it is not filled
above the ‘Max Fill’ mark.
Place the blade assembly onto the
jar (blade side down) and screw the
assembly clockwise into place until
you have a good seal.
NB Ensure that the blade assembly
is fully tightened to prevent any
possible leakage, also that the blade
assembly is level and not cross
threaded.
OR
1
Before blending, you need to choose
the large or the small blending jar
depending on the quantity of blended
food you require.
2
Choosing the correct Jar size
Filling Your Blender with Ingredients
‘Max Fill’

Ensure the motor unit is on a stable
level surface and plugged into the
mains socket.
Turn the jar upside down and place
it into the motor unit ensuring the 3
tabs on the jar align with the 3
notches in the motor base.
Turn the jar a little further clockwise
until the blender operates.
Continue blending until the desired
consistency you require has been
reached.
NB Do not operate the blender
continuously for more than 60
seconds at a time (30 seconds for
dry ingredients). Allow 180
seconds rest time before
continuing to blend.
Tab
Notch
Operating Your Blender
3

Stop the blender by rotating the jar anti-
clockwise a little and then lift it straight up
and remove.
NB The unit will now automatically stop
blending.
If the ingredients have not blended evenly,
remove the jar and blade assembly from
the motor base and shake the jar to
redistribute the ingredients and then repeat
blending once more.
Finally unscrew the blade assembly and
serve.
Removing the Jar after blending
4
5
Serving your blended food

Using Your Flip Top Lid
Using your cover lid
CAUTION Do not put the jars into the freezer
Screw on the flip top lid clockwise
onto the top of either of the two jars in
order to drink the blended contents.
Please click lid fastener down twice to
seal.
NB the flip top lid is not leak proof,
please keep the jar upright at all
times.
You can store previously blended drinks
in the fridge for later. Just screw the cover
lid on clockwise until it is sealed and pop
it into the fridge.
NB the cover lid is not leak proof, please
keep the jar upright at all times.

Suggested uses of your Blender
Use
Suggested Jar Size
Type of food
Nutrient juices/Smoothies
0.5litre or 0.8litre
Fruit/Vegetables
Mixing
0.5litre or 0.8litre
Batters and Dips
Sauces
0.5litre or 0.8litre
Vinaigrettes
Salad dressings
Simple sauces
Frozen blending
0.5litre or 0.8litre
Ice
Frozen fruits
Ice cream
Chopping
0.5litre or 0.8litre
Nuts, Chocolate, Pepper,
etc.
WARNING: To prevent blender overheating, dry ingredients must not be
processed for more than 30 seconds at a time.
If the blender overheats a thermal switch will activate and shut off the motor.
To reset, unplug the appliance and allow it to cool for 30 minutes before using
again.
NB Add a little water whilst blending fruit and vegetables.
Care and maintenance
CAUTION: Ensure the unit is unplugged from the mains power supply before
cleaning.
Do not immerse the motor unit in water or any other liquids.
The jars, lids and blade assembly can be hand washed in warm soapy
water, when handwashing use caution as the blade assembly is sharp and
may cause injury.
To ease washing it is advised to rinse parts immediately after blending.
Do not use scouring pads, harsh or abrasive or solvent based cleaning
products.
DO NOT CLEAN ANY PART OF YOUR BLENDER IN A DISHWASHER
Switch off the appliance and disconnect from the supply before changing
accessories or approaching parts that move in use.

Cleaning Tips
Use a small brush (not supplied) to remove particles lodged beneath the
blades. Care must be taken when cleaning the blade assembly as they are
sharp.
To aid the removal of lodged food or food that has dried onto the jars or blade
assembly, fill the jar 2/3 full with warm soapy water and put through the
blending cycle and repeat with clean water.
CAUTION: Do not attempt to remove blades from the blade assembly for
cleaning.
Troubleshooting
Symptom
Possible reason and solution
Motor doesn’t start or attachment
doesn’t rotate.
Ensure the tabs on the jar are correctly
located in motor unit and the jar is turned fully
clockwise
The mains plug is not inserted into the socket
or the socket is not switched on (if applicable)
Food is chopped unevenly.
The jar may be overfilled - reduce the amount
of ingredients below the ‘Max Fill’ mark
The ingredients may be stuck, - remove and
shake the jar to redistribute contents
Food is too finely chopped or
watery.
The food has been over processed, for best
results use short pulses
Not enough ingredients and/or too much liquid
Cannot achieve ‘snow’from ice
cubes.
For best result use ice straight from the
freezer. Try using short blends instead of one
long one and a little water.
Jar is leaking.
Make sure the lid or blade assembly (as
applicable) is properly attached to the cup and
the threads are not misaligned
Unit doesn’t turn on
Make sure the unit is plugged in.
Make sure the blade assembly is properly
assembled to the jar and that is not
misaligned
Doesn’t blend well
Pulse ingredients for best results, for frozen
foods, blend in 2 second intervals.
Lid/blade assembly will not
properly align to the jar
Set the jar on a level surface. Place the lid or
blade assembly on top of the jar and align the
threads so that the lid/blades sit flat on the jar.
Twist clockwise so that the lid/blades evenly
align to the jar until you have a tight seal.