Daewoo DAST01C User manual

Manufactured under license of Daewoo International Corporation, Korea
www.daewoopowerproducts.com
USER'S MANUAL
DAST01C
JACK STAND

1
INDEX
1 .SPECIFICATIONS..................................................................................................................................... 2
2 .IMPORTANT SAFETY INFORMATION .................................................................................................... 2
3 .OPERATION ............................................................................................................................................. 2
4 . MAINTENANCE AND INSPECTION ........................................................................................................ 3
WARRANTY ................................................................................................................................................. 4

2
EN
MODEL
DAST01C 285 mm 2 405 mm 7 - 1/16 X 6 - 1/2”
CAPACITY
(TON)
MIN.
HEIGHT
MAX.
HEIGHT
BASE
DIMENSIONS
1. SPECIFICATIONS
2. IMPORTANT SAFETY INFORMATION
Read these safety warnings before operation.
WARNING!
Failure to read these warnings may result in personal injury damage
WARNING!
Do not overload Jack stands beyond rated capacity. Overloading can cause damage to or failure of
the Jack stands.
POSITION LOAD ON CENTER OF SADDLE ONLY ALWAYS USING STANDS IN PAIRS ON HARD,
LEVEL SURFACE CAPABLE OF SUSTAINING THE LOAD. USING OF STANDS ON OTHER THAN
HARD LEVEL SURFACES CAN RESULT IN STANDS' INSTABILITY AND POSSIBLE LOSS OF LOAD
3. OPERATION
1. Refer to your vehicle owners manual for proper Jacking procedure.
2. Position stands under vehicle at points specified by vehicle manufacture as proper load support
points.
3. Load just 8 tands: Hold control lever up tile lifting saddle shafl to desired height.
Push control lever down to lock pawl lnto teeth located in center column.
MAKE SURE PAWL IS FULLY ENGAGED INTO TEETH.
4. Carefully lower load onto stands.
4. MAINTENANCE AND INSPECTION
1. Visual inspection shall be made before use of the stands, checking cracks. Cracked welds and
missing and/or dama parts. And stand that appears to be damaged In anyway shall be removed
from service immediately.
2. BECAUSE OF THE POTENTIAL HAZARDS ASSOCIATED THE MISUSE OF EQUIPMENT OF THIS
TYPE, NO REPLACEMENT SHALL BE MADE TO THE PRODUCT.

3
1. SPECIFICATIONS
2. IMPORTANT SAFETY INFORMATION
Read these safety warnings before operation.
WARNING!
Failure to read these warnings may result in personal injury damage
WARNING!
Do not overload Jack stands beyond rated capacity. Overloading can cause damage to or failure of
the Jack stands.
POSITION LOAD ON CENTER OF SADDLE ONLY ALWAYS USING STANDS IN PAIRS ON HARD,
LEVEL SURFACE CAPABLE OF SUSTAINING THE LOAD. USING OF STANDS ON OTHER THAN
HARD LEVEL SURFACES CAN RESULT IN STANDS' INSTABILITY AND POSSIBLE LOSS OF LOAD
3. OPERATION
1. Refer to your vehicle owners manual for proper Jacking procedure.
2. Position stands under vehicle at points specified by vehicle manufacture as proper load support
points.
3. Load just 8 tands: Hold control lever up tile lifting saddle shafl to desired height.
Push control lever down to lock pawl lnto teeth located in center column.
MAKE SURE PAWL IS FULLY ENGAGED INTO TEETH.
4. Carefully lower load onto stands.
4. MAINTENANCE AND INSPECTION
1. Visual inspection shall be made before use of the stands, checking cracks. Cracked welds and
missing and/or dama parts. And stand that appears to be damaged In anyway shall be removed
from service immediately.
2. BECAUSE OF THE POTENTIAL HAZARDS ASSOCIATED THE MISUSE OF EQUIPMENT OF THIS
TYPE, NO REPLACEMENT SHALL BE MADE TO THE PRODUCT.

GUARANTEE
WARRANTY DOES NOT COVER
Product model
Serial number
Username
Date of sale
Company
Client's signature
The warranty period starts from the date of sale of the products and covers 1 year for all power products.
During the warranty period, free failures caused due to the use of poor-quality materials in the production and
manufacturer workmanship admitted fault are removed. The guarantee comes into force only when warranty card
and cutting coupons are properly filled. The product is accepted for repair in its pure form and full completeness.
• Mechanical damage (cracks, chips, etc.) and damage
caused by exposure to aggressive media, foreign objects
inside the unit and air vents, as well as for damage occurred
as a result of improper storage (corrosion of metal parts);
• Failures caused by overloading or product misuse, use of
the product for other purposes. A sure sign of overload
products is melting or discoloration of parts due to the high
temperature, simultaneous failure of two or more nodes,
teaser on the surfaces of the cylinder and the piston or
destruction of piston rings. Also, the warranty does not
cover failure of the automatic voltage regulator due to
incorrect operation;
• Failure caused by clogging of the fuel and cooling systems;
• Wearing parts (carbon brushes, belts, rubber seals, oil
seals, shock absorbers, springs, clutches, spark plugs,
mufflers, nozzles, pulleys, guide rollers, cables, recoil starter,
chucks, collets, removable batteries, filters and safety
elements, grease, removable devices, equipment, knives,
drills, etc.);
• Electrical cables with mechanical and thermal damage;
• Product opened or repaired by a non-authorized service center.
• Prevention, care products (cleaning, washing, lubrication,
etc.), installation and configuration of the product;
• Natural wear products (production share);
• Failures caused by using the product for the needs related
to business activities;
• If the warranty card is empty or missing seal (stamp) of the Seller;
• The absence of the holder's signature on the warranty card.
WARRANTY CARD
The product is in good conditions and fully complete. Read and agree the terms of the warranty.
Product
Model
Company
Date
of sale
Product
Model
Company
Date
of sale

www.daewoopowerproducts.com
Manufactured under license of Daewoo International Corporation, Korea