Daewoo DAFS01 User manual

Manufactured under license of Daewoo International Corporation, Korea
www.daewoopowerproducts.com
USER'S MANUAL
DAFS01/DAFS02
Face shield

1
INDEX
1 .CLEANING AND DESINGECTION ........................................................................................................... 2
2 .ADJUSTING .............................................................................................................................................. 2
WARRANTY ................................................................................................................................................. 3

2
EN
NOTE: If protection against high speed particles at extreme temperatures is required then the
selected face shield should be marked with the letter T immediately after the impact letter, i.e. FT,
BT or AT. If the impact letter is not followed by the letter T then the face shield shall only be used
against high speed particles at room temperature.
WASTE MANAGEMENT: Please refer to local legislations for the proper disposal of packaging
waste, as well as disposal of this product after discontinued service.
The visors are mainly designed for forestry and industry work. It provides an essential impact
protection to the worker’s face.
The materials used in these visors do not contain any substances known to cause allergic reactions.
However, it may be possible for certain susceptible individuals to develop allergies to the material
used.
1. CLEANING AND DISINFECTION
Clean and disinfect only by soft cloth with mild soap and warm water. Solvent or abrasive cleaners
should not be used.
STORAGE
Ideally at 23°C, 55 RH.
SHELL LIFE: 1 year.
REPLACEMENT OF VISOR
Inspect frequently and replace the damaged visors.
MARKING
DAEWOO: Manufacturer identification
EN 1731: Number of European standard
F: Protection against high speed particles, low energy impact
S: Increased robustness
2. ADJUSTING
1. Set the top string.
2. Fasten the turnbuckle on the back.
3. Fasten the bolts on both sides to suitable tightness.
4. Adjust the positioner(4 positions) on both sides to secure the suitable position for the user.
WARNING (DAFS01)
1. The face shield against high speed particles worn over ophthalmic spectacles may transmit
impacts, this creating a hazard to the wearer.
2. The face shield does not protect against liquid splash, hot solids, electrical hazards, IR or UV
radiation.
3. The face shield marked “S” should not be used when there is a foreseeable risk of any hard or
sharp particles.
WARNING (DAFS02)
1. The face shield against high speed particles worn over ophthalmic spectacles may transmit
impacts, this creating a hazard to the wearer.
2. The face shield does not protect against hot solids, electrical hazards, IR or UV radiation.
3. The face shield marked “S” should not be used when there is a foreseeable risk of any hard or
sharp particles.

2
NOTE: If protection against high speed particles at extreme temperatures is required then the
selected face shield should be marked with the letter T immediately after the impact letter, i.e. FT,
BT or AT. If the impact letter is not followed by the letter T then the face shield shall only be used
against high speed particles at room temperature.
WASTE MANAGEMENT: Please refer to local legislations for the proper disposal of packaging
waste, as well as disposal of this product after discontinued service.
The visors are mainly designed for forestry and industry work. It provides an essential impact
protection to the worker’s face.
The materials used in these visors do not contain any substances known to cause allergic reactions.
However, it may be possible for certain susceptible individuals to develop allergies to the material
used.
1. CLEANING AND DISINFECTION
Clean and disinfect only by soft cloth with mild soap and warm water. Solvent or abrasive cleaners
should not be used.
STORAGE
Ideally at 23°C, 55 RH.
SHELL LIFE: 1 year.
REPLACEMENT OF VISOR
Inspect frequently and replace the damaged visors.
MARKING
DAEWOO: Manufacturer identification
EN 1731: Number of European standard
F: Protection against high speed particles, low energy impact
S: Increased robustness
2. ADJUSTING
1. Set the top string.
2. Fasten the turnbuckle on the back.
3. Fasten the bolts on both sides to suitable tightness.
4. Adjust the positioner(4 positions) on both sides to secure the suitable position for the user.
WARNING (DAFS01)
1. The face shield against high speed particles worn over ophthalmic spectacles may transmit
impacts, this creating a hazard to the wearer.
2. The face shield does not protect against liquid splash, hot solids, electrical hazards, IR or UV
radiation.
3. The face shield marked “S” should not be used when there is a foreseeable risk of any hard or
sharp particles.
WARNING (DAFS02)
1. The face shield against high speed particles worn over ophthalmic spectacles may transmit
impacts, this creating a hazard to the wearer.
2. The face shield does not protect against hot solids, electrical hazards, IR or UV radiation.
3. The face shield marked “S” should not be used when there is a foreseeable risk of any hard or
sharp particles.

GUARANTEE
WARRANTY DOES NOT COVER
Product model
Serial number
Username
Date of sale
Company
Client's signature
The warranty period starts from the date of sale of the products and covers 2 years for all power products.
During the warranty period, free failures caused due to the use of poor-quality materials in the production and
manufacturer workmanship admitted fault are removed. The guarantee comes into force only when warranty card
and cutting coupons are properly filled. The product is accepted for repair in its pure form and full completeness.
• Mechanical damage (cracks, chips, etc.) and damage
caused by exposure to aggressive media, foreign objects
inside the unit and air vents, as well as for damage occurred
as a result of improper storage (corrosion of metal parts);
• Failures caused by overloading or product misuse, use of
the product for other purposes. A sure sign of overload
products is melting or discoloration of parts due to the high
temperature, simultaneous failure of two or more nodes,
teaser on the surfaces of the cylinder and the piston or
destruction of piston rings. Also, the warranty does not
cover failure of the automatic voltage regulator due to
incorrect operation;
• Failure caused by clogging of the fuel and cooling systems;
• Wearing parts (carbon brushes, belts, rubber seals, oil
seals, shock absorbers, springs, clutches, spark plugs,
mufflers, nozzles, pulleys, guide rollers, cables, recoil starter,
chucks, collets, removable batteries, filters and safety
elements, grease, removable devices, equipment, knives,
drills, etc.);
• Electrical cables with mechanical and thermal damage;
• Product opened or repaired by a non-authorized service center.
• Prevention, care products (cleaning, washing, lubrication,
etc.), installation and configuration of the product;
• Natural wear products (production share);
• Failures caused by using the product for the needs related
to business activities;
• If the warranty card is empty or missing seal (stamp) of the Seller;
• The absence of the holder's signature on the warranty card.
WARRANTY CARD
The product is in good conditions and fully complete. Read and agree the terms of the warranty.
Product
Model
Company
Date
of sale
Product
Model
Company
Date
of sale

www.daewoopowerproducts.com
Manufactured under license of Daewoo International Corporation, Korea