Daikin EWWD320DZXSA1 Owner's manual

D-EIMWC01405-18EN- 1/32
REV
01
Date
July 2018
Supersedes
D–EIMWC01405-18EN
WATER COOLED OIL FREE CENTRIFUGAL CHILLERS
EWWD –DZ
EWWH - DZ
Cooling capacity from 320 to 1480 kW
50Hz - Refrigerant: HFC R134a, R1234ze(E)
Original Instructions
Installation, maintenance and operating manual
D–EIMWC01405-18_01EN

D-EIMWC01405-18EN- 2/32
Contents
1INTRODUCTION......................................................................................................................................................................6
1.1 General Description..................................................................................................................................................................6
1.2 Application................................................................................................................................................................................6
1.3 Information about R1234ze(E)..................................................................................................................................................6
1.4 Installation Safety.....................................................................................................................................................................7
1.4.1 Additional guidelines for safe use of R1234ze(E) for equipment located in the open air............................................7
1.4.2 Additional guidelines for safe use of R1234ze(E) for equipment located in a machinery room...................................7
2INSTALLATION.......................................................................................................................................................................9
2.1 Storage.....................................................................................................................................................................................9
2.2 Receiving and handling ............................................................................................................................................................9
2.3Lifting instructions...................................................................................................................................................................10
2.4 Positioning and assembly.......................................................................................................................................................11
2.5 Shock absorbers.....................................................................................................................................................................11
2.6 Anchoring...............................................................................................................................................................................12
2.7 Water pipes............................................................................................................................................................................12
2.7.1 Evaporator and condenser water pipes...................................................................................................................12
2.7.2 Flow Switch ............................................................................................................................................................12
2.8 Water treatment......................................................................................................................................................................13
2.9 Temperature limits and water flow..........................................................................................................................................14
2.10 Minimum water content in the system.....................................................................................................................................14
2.11 Evaporator frost protection......................................................................................................................................................15
2.12 Condenser protection and design considerations....................................................................................................................15
2.12.1 Condensation control with evaporative cooling tower.........................................................................................15
2.12.2 Condensation control with well water.................................................................................................................16
2.13 Chilled water control sensor....................................................................................................................................................16
2.14 Safety Valve...........................................................................................................................................................................17
2.15 Open the isolation and/or shut off valves ................................................................................................................................17
2.16 Electrical connections.............................................................................................................................................................17
2.17 Phase imbalance....................................................................................................................................................................17
2.18 Control circuit .........................................................................................................................................................................17
3OPERATION..........................................................................................................................................................................19
3.1 Operator’s responsibilities.......................................................................................................................................................19
3.2 Unit description.......................................................................................................................................................................19
3.3 Safeties for each cooling compressor.....................................................................................................................................20
3.4 System safeties......................................................................................................................................................................20
3.5 Regulation type.......................................................................................................................................................................20
3.6 Compressor Lead-Lag............................................................................................................................................................20
3.7 High condensing pressure control...........................................................................................................................................20
4MAINTENANCE.....................................................................................................................................................................21
4.1 Pressure/Temperature Table..................................................................................................................................................22
4.2 Routine maintenance..............................................................................................................................................................23
4.2.1 Check condenser performance...............................................................................................................................23
4.2.2 Electronic expansion valve......................................................................................................................................23
4.2.3 Cooling circuit.........................................................................................................................................................23
4.2.4 Refrigerant charge..................................................................................................................................................26
4.2.5 Check the refrigerant charge...................................................................................................................................26
4.2.6 Electrical Installation...............................................................................................................................................26
4.3 Cleaning and Storage.............................................................................................................................................................27
4.4 Seasonal maintenance...........................................................................................................................................................27
4.4.1 Seasonal shutdown ................................................................................................................................................27
4.4.2 Seasonal start up....................................................................................................................................................27
5SERVICE SCHEDULE...........................................................................................................................................................27
6MAINTENANCE SCHEDULE.................................................................................................................................................28
7CHECKS BEFORE FIRST START UP...................................................................................................................................29
8IMPORTANT INFORMATION ON USED REFRIGERANT.....................................................................................................30
8.1 Factory and Field charged units instructions...........................................................................................................................30
9PERIODIC CHECKS AND COMMISSIONING OF PRESSURE VESSELS............................................................................31
10 DEMOLITION AND DISPOSAL .............................................................................................................................................31
11 DURATION ............................................................................................................................................................................31
List of Figures
Fig. 1 - Single compressor unit component descriptions...........................................................................................................................3
Fig. 2 - Dual compressor unit component descriptions..............................................................................................................................4
Fig. 3-Description of the labels applied to the electric panel......................................................................................................................5
Fig. 4 - Unit positioning...........................................................................................................................................................................11
Fig. 5-Water quality................................................................................................................................................................................13
Fig. 6 –Electrical Panel Layout ..............................................................................................................................................................20
Fig. 7-P&ID Mono and Dual compressor ................................................................................................................................................24
Fig. 8-P&ID Mono and Dual compressor with economizer......................................................................................................................25

D-EIMWC01405-18EN- 3/32
Fig. 1 - Single compressor unit component descriptions

D-EIMWC01405-18EN- 4/32
1
2
3
4
5
6
7
8
9
10
11
Low pressure
transducer
Evaporator outlet
water temperature
sensor
Evaporator inlet
water temperature
sensor
Condenser outlet
water temperature
sensor
Condenser inlet
water temperature
sensor
Air purge
Water drain
Liquid line
shut-off valve
High
pressure
safety valves
Refrigerant
charge service
valve
Starter
valve
12
13
14
15
16
17
18
19
20
21
Liquid line
expansion
valve
Economizer line
expansion valve
Economizer line
temperature sensor
Economizer line
pressure
transducer
Suction
temperature sensor
High pressure
transducer
Liquid
temperature
sensor
Low
Pressure
safety valves
Service valve
Inverter cooling
line inlet
Fig. 2 - Dual compressor unit component descriptions

D-EIMWC01405-18EN- 5/32
Fig. 3-Description of the labels applied to the electric panel
Identification of labels
1 –Manufacturer’s logo
6–Wire tightness check
2–Electricity warning
7–Shock hazard
3–Emergency button
8–Lifting instructions
4–Type of gas
9–Unit nameplate
5–UN 2875

D-EIMWC01405-18EN- 6/32
1 INTRODUCTION
This manual provides information on the functions and standard procedures for all series units and is an important support
document for qualified personnel but can never replace them.
All units are supplied complete with wiring diagrams and dimensional drawings that provide information about the size and
weight of each model.
In case of discrepancies between the content of the manual and the documentation that came with the unit, always rely to
the wiring diagram and dimensional drawings because they are an integral part of this manual.
Read this manual carefully before installing and starting up the unit.
Improper installation can cause: short circuits, leaks, fire or other damages to the equipment or personal injuries.
The unit must be installed by professionals/professional technicians in accordance with current laws of the country of
installation.
The unit must also be started by authorized and trained personnel and all activities must be conducted in accordance and
in full compliance with local standards and laws.
IF THE INSTRUCTIONS IN THIS MANUAL ARE NOT CLEAR, DO NOT INSTALL AND/OR START UP THE UNIT.
If in doubt, for service and further information, contact the manufacturer's authorized representative.
1.1 General Description
Daikin water chillers, with centrifugal compressors and magnetic bearings, are completely factory assembled and tested
before shipment.
The EWWD(H) DZ range consists of models with a single compressor and single cooling circuit (from 320 to 740 kW) and
models with two compressors and single cooling circuit (610 to 1480 kW)
The controller is pre-wired, set and tested at the factory.
Only normal connections are required on site such as piping, electrical connections and pump interlocks, making
installation easier and more reliable. All operating safety and control systems are factory installed in the control panel. The
instructions in this manual apply to all models of this series unless otherwise indicated.
1.2 Application
The EWWD(H) DZ units with centrifugal compressor and adjustment inverters are designed and constructed to cool
buildings or industrial processes. Daikin technicians, specifically trained for this purpose, must start the final system for the
first time. Failure to follow this starting procedure affects the warranty.
The standard warranty covers parts of this equipment with proven defects in material or workmanship. Materials subject to
natural consumption are not, however, covered by the warranty.
The cooling towers used with Daikin units must be selected for a wide scope of application, as described in the "Operating
limits" section. From an energy savings point of view it is always preferable to keep the temperature difference between
the hot circuit (condenser) and the cold circuit (evaporator) to a minimum. However, it is always necessary to verify that
the machine works in the temperature range specified in this manual.
1.3 Information about R1234ze(E)
This product is equipped with refrigerant R1234ze(E) which has minimal impact to the environment, thanks to its low value
of Global Warming Potential (GWP). R1234ze(E) refrigerant is classified by European Directive 2014/68/EU as a Group 2
(non-dangerous) substance, as it is nonflammable at standard ambient temperature and non-toxic. Due to this, no special
precautions are required for storage, transport and handling.
Daikin Applied Europe S.p.A. products comply with applicable European Directives and refer for unit design to product
Standard EN378:2016 and industrial Standard ISO5149. Local authorities approval should be verified referring to European
Standard EN378 and/or ISO 5149 (where R1234ze(E) is classified A2L –Mildly flammable gas).

D-EIMWC01405-18EN- 7/32
Physical characteristics of refrigerant R1234ze (E)
Safety Class
A2L
PED Fluid Group
2
Pratical limit (kg/m3)
0.061
ATEL/ ODL (kg/m3)
0.28
LFL (kg/m3)@ 60°C
0.303
Vapour density @25°C, 101.3 kPa (kg/m3)
4.66
Molecular Mass
114.0
Normal Boling Point (°C)
-19
GWP (100 yr ITH)
7
GWP (ARS 100 yr ITH)
<1
Auto Ignition Temperature (°C)
368
1.4 Installation Safety
All EWWD(H) VZ machines are built in accordance with the main European Directives (Machinery Directive, Low Voltage
Directive, Electromagnetic Compatibility Directive for PED pressurized equipment), make sure you also receive the
declaration of product conformity with the directives along with the documentation.
Before machine installation and commissioning, the people involved in this activity must have acquired the information
necessary to carry out these tasks, applying all the information collected in this book.
Do not allow unauthorized and/or unskilled personnel to access the unit.
Always protect the operating personnel with personal protective equipment appropriate for the tasks to be performed.
Commonly used personal equipment include: protective helmet, goggles, gloves, headphones, safety shoes. Additional
individual and group protective equipment should be adopted after an adequate analysis of the specific risks in the area of
relevance, according to the activities to be performed.
The chiller has to be installed in open air or machinery room (location classification III).
To ensure location classification III a mechanical vent on the secondary circuit(s) has to be installed.
Local building codes and safety standards shall be followed; in absence of local codes and standards refer to EN 378-
3:2016 as a guide.
In paragraph “Additional guidelines for safe use of R1234ze(E)” there are provided additional informations that should be
added to the requirements of safety standards and building codes.
1.4.1 Additional guidelines for safe use of R1234ze(E) for equipment located in the open air
Refrigerating systems sited in the open air shall be positioned to avoid leaked refrigerant flowing into a building or otherwise
endangering people and property.
The refrigerant shall not be able to flow into any ventilation fresh air opening, doorway, trap door or similar opening in the
event of a leak. Where a shelter is provided for refrigerating equipment sited in the open air it shall have natural or forced
ventilation.
For refrigeration systems installed outside in a location where a release of refrigerant can stagnate e.g. below ground, then
the installation shall comply with the requirements for gas detection and ventilation of machinery rooms.
1.4.2 Additional guidelines for safe use of R1234ze(E) for equipment located in a machinery room
When a machinery room is chosen for the location of the refrigerating equipment it shall be located in accordance with
local and national regulations. The following requirements (according to EN 378-3:2016) can be used for the assessment.
A risk analysis based on the safety concept for the refrigerating system (as determined by the manufacturer and
including the charge and safety classification of the refrigerant used) shall be conducted to determine whether it
is necessary to place the refrigerating system in a separate refrigeration machinery room.
Machinery rooms should not be used as occupied spaces. The building owner or user shall ensure that access
is permitted only by qualified and trained personnel doing the necessary maintenance to the machinery room or
general plant.
Machinery rooms shall not be used for storage with the exception of tools, spare parts and compressor oil for the
installed equipment. Any refrigerants, or flammable or toxic materials shall be stored as required by national
regulations.
Open (naked) flames shall not be permitted in machinery rooms, except for welding, brazing or similar activity
and then only provided the refrigerant concentration is monitored and adequate ventilation is ensured. Such
open flames shall not be left unattended.
A remote switching (emergency type) for stopping the refrigerating system shall be provided outside the room
(near the door). A similar acting switch shall be located at a suitable location inside the room.
All piping and ducting passing throught floors, ceiling and walls of machinery room shall be sealed.
Hot surfaces shall not exceed a temperature of 80 % of the auto-ignition temperature (in °C) or 100 K less than
the auto-ignition temperature of the refrigerant, whichever is higher.


D-EIMWC01405-18EN- 8/32
Refrigerant
Auto ignition temperature
Maximum surface temperature
R1234ze
368 °C
294 °C
Machinery rooms shall have doors opening outward and sufficient in number to ensure freedom for persons to
escape in an emergency; the doors shall be tight fitting, self-closing and so designed that they can be opened
from inside (antipanic system).
Special machinery rooms where the refrigerant charge is above the practical limit for the volume of the room
shall have a door that either opens directly to the outside air or through a dedicated vestibule equipped with
self-closing, tight-fitting doors.
The ventilation of machinery rooms shall be sufficient both for normal operating conditions and emergencies.
Ventilation for normal operating conditions shall be in accordance with national regulations.
The emergency mechanical ventilation system shall be activated by a detector(s), located in the machinery
room.
oThis ventilation system shall be:
independent of any other ventilation system on the site.
provided with two independent emergency controls one located outside the machinery room,
and the other inside.
oThe emergency exhaust ventilation fan shall:
Be either in the air flow with the motor outside the airflow, or rated for hazardous areas
(according to the assessment).
Be located to avoid pressurization of the exhaust ductwork in the machinery room.
not cause sparks to occur if it contacts the duct material.
oAirflow of the emergency mechanical ventilation shall be at least
𝑉 = 0,014 × 𝑚23
⁄
where
V
is the air flow rate in m3/s;
m
is the mass of refrigerant charge, in kg, in the refrigerating system with the largest charge, any
part of which is located in the machinery room;
0,014
is a conversion factor.
oMechanical ventilation shall be operated continuously or shall be switched on by the detector.
Detector shall automatically activate an alarm, start mechanical ventilation and stop the system when it triggers.
The location of detectors shall be chosen in relation to the refrigerant and they shall be located where the
refrigerant from the leak will concentrate.
The positioning of the detector shall be done with due consideration of local airflow patterns, accounting for
location sources of ventilation and louvers. Consideration shall also be given to the possibility of mechanical
damage or contamination.
At least one detector shall be installed in each machinery room or the occupied space being considered and/or
at the lowest underground room for refrigerants heavier than air and at the highest point for refrigerants lighter
than air.
Detectors shall be continuously monitored for functioning. In the case of a detector failure, the emergency
sequence should be activated as if refrigerant had been detected.
The pre-set value for the refrigerant detector at 30 °C or 0 °C, whichever is more critical, shall be set to 25 % of
the LFL. The detector shall continue to activate at higher concentrations.
Refrigerant
LFL
Pre-set alarm
R1234ze
0,303 kg/m3
0,07575 kg/m3
16500 ppm
All electrical equipment (not only the refrigerating system) shall be selected to be suitable for use in the zones
identified in the risk assessment. Electrical equipment shall be deemed to comply with the requirements if the
electrical supply is isolated when the refrigerant concentration reaches 25 % of the lower flammable limit or
less.
Machinery rooms or special machinery rooms shall be clearly marked as such on the entrances to the room,
together with warning notices indicating that unauthorized persons shall not enter and that smoking, naked light
or flames are prohibited. The notices shall also state that, in the event of an emergency, only authorized
persons conversant with emergency procedures shall decide whether to enter the machinery room. Additionally,
warning notices shall be displayed prohibiting unauthorized operation of the system
The owner / operator shall keep an updated logbook of the refrigerating system.
The optional leak detector supplied by DAE with the chiller should be used exclusively to check
refrigerant leakage from the chiller itself

D-EIMWC01405-18EN- 9/32
2 INSTALLATION
2.1 Storage
Should it be necessary to store the unit prior to installation, it is necessary to observe some precautions.
Do not remove the protective plastic
Do not leave the unit exposed to the elements
Do not expose the unit to direct sunlight
Do not use the machine near a heat source and/or open flame
Keep in places where room temperature is between + 5° C to 55° C (room temperature over the maximum limit
may trigger the safety valve resulting in loss of refrigerant.
2.2 Receiving and handling
Inspect the unit immediately after delivery. In particular, make sure the machine is intact in all its parts and that there are
no deformations due to collisions. Should damages be found upon receipt, immediately file a written complaint with the
carrier.
Machine returns are Ex factory Daikin Applied Europe S.p.A.
Daikin Applied Europe S.p.A. cannot be held liable for any equipment damages incurred during transportation to the place
of destination.
The isolation of the evaporator corners, where the lifting holes are located, are shipped separately and must be assembled
on site after the unit has been permanently installed. Even the anti-vibration supports (optional) are shipped separately.
Make sure these items, if required, are delivered with the unit.
Use extreme caution when handling the unit to prevent damage to the control panel and the refrigerant pipes.
The unit must be lifted by inserting a hook in each of the four corners, where the lifting holes are located (see lifting
instructions). Distancer bars must be used along the line connecting the lifting holes to prevent damages to the electrical
panel and the compressor terminal box (see figure). Do not use any other point to lift the machine.
During the lifting phase, check that the lifting cords and/or chains do not touch the electrical panel and/or piping.
If, to move the machine, slides or moving skates are used, just push the base of the machine without touching the pipes,
compressors and/or electric panel.
Be careful not to hit, during handling, pipes, cables and installed accessories.
All the necessary devices guaranteeing personal safety must be provided during machine handling.
Refer to the dimensional drawing for hydraulic and electrical unit connections.
The overall machine dimensions, as well as the weights described in this manual, are purely
indicative.
The contract dimensional drawing and relevant wiring diagram are provided to the customer when
ordering.

D-EIMWC01405-18EN- 10/32
2.3 Lifting instructions
Single compressor unit
Dual compressor unit
Fig. 1 –Lifting instructions

D-EIMWC01405-18EN- 11/32
Lifting instructions:
1) The equipment, slings, lifting accessories and handling procedures must meet local regulations and current standards.
2) To lift the machine, use only the holes on the heat exchangers.
3) Any lifting points should be used during handling.
4) Use lifting hooks with closing device exclusively. Hooks must be safely secured before handling.
5) The ropes and hooks used must have capacity suited to the load. Check the nameplate on the unit that indicates the
machine weight.
6) The installer must correctly select and use lifting equipment. We recommend using cables with minimum vertical
capacity equal to total machine weight.
7) The machine must be lifted slowly and well leveled. If necessary, adjust lifting equipment to guarantee levelling.
2.4 Positioning and assembly
The unit must be mounted on a level cement or steel base, suitable to support the overall weight of the complete machine
in operation, and must be positioned so as to provide space for maintenance, to allow the cleaning and/or the removal of
the evaporator and the condenser pipes. Refer to the figure below for the areas of respect. The condenser and evaporator
pipes are expanded inside the tube sheetto allow replacement, if necessary.
Fig. 4 - Unit positioning
The machine position should be designed to ensure access to all the safety and control devices. Never cover the safety
devices (safety valves, pressure switches), which, due to their importance, are subject to periodic checks. The safety
valves outlet must be connected before operations. For safety valve outlet pipe dimensions, we recommend applying
harmonized standards and EN13136.
These units include the installation of two safety valves for each exchanger, installed on an exchange tap, which always
maintains an active valve. Thus, both safety valves on each exchanger must be connected outside the engine room. These
pipes must be installed so that, in case the valve opens, the discharged refrigerant flow not invest people and/or things, or
can enter the building through windows and/or other openings.
The engine room must be adequately ventilated to prevent refrigerant accumulation inside that can deprive air of the right
oxygen content and thuscause asphyxiation. In this regard, we recommend the application of harmonized standard EN378-
3 (Safety and Environmental Requirements - Installation and protection of persons) or equivalent.
The air contaminated by a high percentage of refrigerant (see refrigerant safety sheet), can cause
asphyxiation, loss of mobility and consciousness if inhaled. Avoid eye and skin contact.
2.5 Shock absorbers
The anti-vibration rubber pads (optional), shipped separately, should be placed under the corners of the unit (except for
special specifications). These provide a minimum insulation. Pads are recommended on all installations where the
transmission of vibrations can be considerable. Also install the anti-vibration joints on water pipes to reduce the stress on
pipes, vibrations and noise.

D-EIMWC01405-18EN- 12/32
The units are shipped with refrigerant valves closed to isolate such fluids during shipment. The
valves must remain closed until such time as an authorized Daikin technician, after inspecting the
machine and checked its installation, commissions the machine.
2.6 Anchoring
After positioning, the machine must be firmly anchored to the ground or foreseen metal structure to support the machine.
In this regard, 22 mm diameter holes are included on the machine base to ensure the anchoring.
2.7 Water pipes
2.7.1 Evaporator and condenser water pipes
The condensers and evaporators are provided with grooved sleeves for Victaulic connections or optionally with flanged
connections. The installer must provide the mechanical coupling with the connections appropriately sized to the system.
Some pressure couplings are included on both the inlet and outlet of the exchangers heads. These couplings control water
load loss.
Make sure that the water inlet and outlet connections agree with the dimensional drawing and the indications found on the
connections. Incorrect water pipe installation could create machine malfunctions and/or reduce performance.
NOTE
When using a hydraulic connection shared with the heating system, make sure the temperature of the water flowing into
the evaporator does not exceed the maximum allowed value. This phenomenon might cause the safety valve to open and
thus the refrigerant to discharge into the atmosphere.
The pipes, before being attached to the machine, must be supported to reduce the weight and the stress on connections.
In addition, the pipes must be adequately insulated. A water filter that can be inspected must also be installed on both
inputs (evaporator and condenser). Install shutoff valves on both heat exchangers with suitable dimensions to permit
draining and inspection without having to completely drain the system.
To prevent damage to exchanger pipes, install a mechanical filter that can be inspected on each input,
able to filter solid objects greater than 1.2 mm in size
2.7.2 Flow Switch
A flow switch must be installed on the evaporator inlet pipe to ensure the correct water flow rate, before the unit is started.
Furthermore, this device shuts off the unit when water flow is interrupted, protecting the machine from the evaporator
freezing.
The flow switch must not be used as a machine control system
The absence of the flow switch on the evaporator water connection, voids the warranty for frost damage.
The evaporator and condenser are not self-draining; both must be purged
Thermometers and pressure gages must be installed on the water pipes near the heat exchangers connections.
Furthermore, vent valves must also be installed at the highest points on the pipe.
If necessary, the evaporator and condenser water box can be reversed. If this operation is completed, control sensors
have to be repositioned and gasket replaced.
If water pump noise could be excessive, we recommend using rubber insulating joints at both pump inlet and outlet. In
most cases it is not necessary to install anti-vibration joints on condenser pipe inlet and outlet but, where the noise and
vibration are critical (for example where a buried pipe passes through a wall in an inhabited area), it may be necessary.
If a cooling tower is used, a balancing valve must be installed. A temperature control system is required if the water tower
is very cold. The controller installed on the machine manages tower fan on/off or continuously manages a control valve or
fan speed controller by means of a 0-10 V DC analog signal. We recommend that you carry out the connection, allowing
fan management by the machine controller (see wiring diagram for connection).

D-EIMWC01405-18EN- 13/32
2.8 Water treatment
Before commissioning the machine, clean the
water circuits. Make sure that the tower purge and
emptying system is operational. Atmospheric air
contains many contaminants so you need a good
water treatmentr.
The use of untreated water canresult in: corrosion,
erosion, mud, fouling and formation of algae.
Daikin Applied Europe is not liable for equipment
damage or malfunction due to a lack of a water
treatment or water not properly treated.
Use industrial glycol only.
Do not use automotive antifreeze.
Automotive antifreeze contains
inhibitors which cause a plating
on copper pipes.
Used glycol handling and
disposal must be in accordance
with current regulations
Fig. 5-Water quality

D-EIMWC01405-18EN- 14/32
2.9 Temperature limits and water flow
EWWD(H) DZ units are designed to operate with an evaporate outlet water temperature between 4°C and +20°C and a
condenser outlet water temperature between 20°C and 50°C. However, the minimum temperature difference between the
evaporator outlet water temperature and the condenser inlet water temperature must not be less than 15° C. Always check
the exact operating point with the selection software. Some simultaneous operating conditions (high evaporator inlet water
temperature and high condenser inlet water temperature) may be inhibited. The maximum permissible water temperature
in the evaporator with the machine off is 50° C. Higher temperatures could cause the safety valves on the evaporator
sleeve to open. Water flow rate in the condenser and evaporator under the rated value indicated in the unit selection point
can cause freezing problems, scale and poor control. Water flow rate in the condenser and evaporator higher than the
rated value indicated in the unit selection point results in an unacceptable pressure drop and excessive erosion of the
pipes and vibrations that can cause breakage.
EWWD(H)-DZ DRY COOLER VERSION
Dry cooler version Model
EWWD320DZXSA1
EWWH230DZXSA1
EWWD340DZXEA1
EWWH245DZXEA1
EWWD440DZXSA1
EWWH320DZXSA1
EWWD470DZXEA1
EWWH345DZXEA1
EWWD610DZXSA2
EWWH430DZXSA2
EWWD640DZXSA2
EWWH455DZXSA2
EWWD670DZXEA2
EWWH470DZXEA2
EWWD680DZXEA2
EWWH490DZXEA2
EWWD880DZXSA2
EWWH640DZXSA2
EWWD950DZXEA2
EWWH685DZXEA2
EWWD(H)-DZ COOLING TOWER VERSION
Cooling tower version Model
EWWD530DZXSA1
EWWH380DZXSA1
EWWD570DZXEA1
EWWH405DZXEA1
EWWD700DZXSA1
EWWH460DZXSA1
EWWD740DZXEA1
EWWH480DZXEA1
EWWDC10DZXSA2
EWWH755DZXSA2
EWWDC11DZXEA2
EWWH810DZXEA2
EWWDC14DZXSA2
EWWH920DZXSA2
EWWDC15DZXEA2
EWWH955DZXEA2
Legend:
ELWT Evaporator outlet water temperature
CLWT Condenser outlet water temperature
2.10 Minimum water content in the system
For correct machine operations and the necessary operating stability, it is important to ensure a minimum water content in
the system. An accumulation tank with suitable volume may be required for this purpose.
The minimum water content must be calculated by considering the following specifications:

D-EIMWC01405-18EN- 15/32
Application
Mono Compressor
Dual Compressor
Conditioning
3.3 lt/kW
2.5 lt/kW
Process
6.6 lt/kW
5.0 lt/kW
Variable capacity
6.6 lt/kW
5.0 lt/kW
Calculation example for EWWD(H)950DZXE units
Cooling capacity at 100% = 946 kW
Minimum system volume for conditioning: 946 x 3.3= 3122 lt
Minimum system volume for processing: 946 x 6.6= 6243 lt
Minimum system volume at variable capacity: 946 x 6.6= 6243 lt
Note: The calculation formula described above, takes into account several factors such as the compressor stop time and
the admissible temperature difference between the last compressor stop and start. In this regard, the minimum water
content calculated refers to the machine operations in a normal climate control system. If the machine is used for process
activities or if higher operating stability is required, we recommend doubling the calculated water content. In very simple
systems, an inertial accumulation tanks may be necessary on the hydraulic circuit to reach the required minimum water
volume. Adding this component must guarantee correct water mixing and, therefore, we recommend you select a tank that
includes an internal diaphragm for this purpose.
Note: If the evaporator water circuit operates in a variable flow system, the minimum water flow rate must not be less than
50% of the water flow at nominal conditions, and the variation should not be greater than 10% of the nominal flow per
minute.
2.11 Evaporator frost protection
1. If the machine is idle during the winter, drain and rinse the evaporator and chilled water pipes with glycol. Drain and
air vent connections are included on the evaporator for this purpose.
2. We recommend adding glycol in proper proportion to the condenser cooling system. The freezing temperature, of
the water-glycol solution, must be at least 6° C lower than the expected minimum ambient temperature.
3. Insulate pipes especially chilled water ones to avoid condensation.
Damage caused by freezing is not covered by warranty, therefore, Daikin Applied Europe SpA cannot
be held liable.
2.12 Condenser protection and design considerations
If lake, river or ground water is used as the cooling fluid and the water valves have a leak, the condenser and liquid
refrigerant line temperatures could drop under room temperature when the machine is off. This problem occurs when cold
water circulates through the condenser and the unit remains off waiting load. If this happens:
1. Turn off the condenser water pump when the compressor is off.
2. Check that the liquid line expansion valve is working properly.
2.12.1 Condensation control with evaporative cooling tower
The minimum condenser inlet water temperature should not be less than 20° C at full water tower flow rate.
If the water temperature must be lower, even the water flow must be reduced proportionately.
To modulate the water flow to the condenser, install a three-way by-pass valve. The figure shows how the three-way valve
is applied to cool the condenser. The three-way valve can be activated by a pressure actuator which guarantees proper
condensing pressure in the case where the water temperature entering the condenser is less than 20° C. A three-way
servo-controlled valve or inverter driven circulation pump could be used instead of a valve with pressure actuator. Both of
these devices could be controlled by a 0-10 Vdc analogue signal emitted by the machine electronic controller according to
the condenser inlet water temperature.
Fig. 3 –Condenser control scheme with cooling tower
1
Cooling tower

D-EIMWC01405-18EN- 16/32
2.12.2 Condensation control with well water
If ground water is used to cool the condenser, install a normally regulating control valve, direct drive, at condenser outlet.
This regulating valve must ensure an adequate condensing pressure in the case where the water temperature entering the
condenser is less than 20° C.
A service valve with pressure outlet is provided on the condenser shell for this purpose.
The valve must modulate its opening according to condensing pressure. When the machine shuts down, the valve will
close preventing the condenser from emptying.
Fig. 4 –Condensation control scheme with well water
1
From the main condenser pump
2
Service valve
3
Direct acting water regulating valve
4
Configuration required when the regulating valve is not used
5
At Drain
2.13 Chilled water control sensor
The water cooled EWWD(H) VZ unit is equipped with a microprocessor. Be careful when working around the unit to avoid
damaging cables and sensors. Check cables before starting the unit. Prevent rubbing of the cables on the frame or other
components. Make sure the cables are securely locked. If the temperature sensor is removed for maintenance, do not
eliminate the conductive paste in the well and replace the sensor correctly. After replacing the sensor, tighten the lock nut
to prevent accidental slipping.
2
Condenser
1
2

D-EIMWC01405-18EN- 17/32
2.14 Safety Valve
Each exchanger (evaporator and condenser) is provided with a safety valve installed on a changeover valve that allows
maintenance and periodic checks, without losing a significant amount of refrigerant. Do not leave the changeover device
in the intermediate position.
To prevent damages due to inhalation and direct contact with refrigerant gas, the safety valve outlets
must be connected with a conveyor pipe before operations. These pipes must be installed so that, in
case the valve opens, the discharged refrigerant flow not invest people and/or things, or can enter
the building through windows and/or other openings. The installer is responsible for connecting the
safety valve to the purge pipe and pipe dimensioning. In this regard, refer to the harmonized standard
EN13136 to dimension the drain pipes to be connected to the safety valves
2.15 Open the isolation and/or shut off valves
Before powering the machine and thus starting the compressors, open all valves that were closed at the factory for
shipping.
The valves to be opened are:
Valve (optional) installed on the discharge line.
Liquid line valve installed under the condenser.
Valve on the liquid injection line (inverter cooling).
Valve (optional) installed on the suction line.
2.16 Electrical connections
The unit must be connected with copper wire of adequate section, based on the maximum absorbed current indicated on
the unit label and in accordance with applicable electrical regulations.
Daikin Applied Europe S.p.A. cannot be held liable for improper electrical connections.
The connections to the terminals must be made with copper terminals and cables.
The electrical connection must be made by qualified personnel.
There is a risk of electric shock
The electrical panel must be connected keeping the correct phase sequence.
2.17 Phase imbalance
In a three-phase system, excessive imbalance between the phases is the cause of motor overheating. The maximum
allowed voltage imbalance is 2%, calculated as follows:
𝐼𝑚𝑏𝑎𝑙𝑎𝑛𝑐𝑒 % = (𝑉𝑥 −𝑉𝑚)∗100
𝑉𝑚
Vx = phase with greatest imbalance
Vm = average of the voltages
I.e. the three phases measure 383, 386 and 392 volts respectively, the average is:
383+386+392 = 387 V
3
The percentage of imbalance is thus:
(392-387) x 100 = 1,29% less than the maximum admitted (2%)
387
Before any maintenance and/or electrical connection to the compressor inverter, make sure the
system is turned off and the unit main switch open.
After turning off the main switch, wait at least 20 minutes for the inverter condensers to completely
discharge. Do not perform any maintenance and/or electrical connection in this period of time.
2.18 Control circuit
Each EWWD(H) VZ unit is factory tested. Both the control and power circuits undergo a careful functional test before the
machine is shipped.
The EWWD(H) VZ unit control circuit is powered at 230 Vac.
The controller ON/OFF switch (Q0) must be rotated to the OFF position whenever machine operations are not required.

D-EIMWC01405-18EN- 18/32
Water flow switch interlock terminals are included in the controller. See the wiring diagram for the correct connections on
the field.
The purpose of the water flow switch interlock is to prevent the compressor from running for enough time to let the two
evaporator and condenser water pumps to operate and ensure the correct water flow. The flow switch can be supplied on
request from Daikin Applied Europe and in any case must be compulsorily installed on the machine. For better protection
against freezing, connecting the evaporator flow switch, connect free contact or pump circuit breaker contact in series.
It is best to leave pump control to the microprocessor for better system management.
If an external system independently manages pump start, follow this logic.
Evaporator water inlet
turn on the pump 2 minutes before enabling the machine
turn off the pump 5 minutes after disabling the machine
Condenser water pumps:
turn the pump on 30 seconds before enabling the machine
turn the pump off 1 minute after the last compressor is turned off.

D-EIMWC01405-18EN- 19/32
3 OPERATION
3.1 Operator’s responsibilities
It is important that the operator becomes familiar with the equipment before operating the machine. In addition to reading
this manual, the operator should study the operation manual and the wiring diagram supplied with the unit to understand
commissioning, operation and the shutdown sequence as well as the shutdown mode and safeties.
During initial machine start-up, the Daikin technician is available to answer any questions and instruct on proper operating
procedures.
The operator should keep an operating data log for each specific machine. Furthermore, an additional maintenance log
should be kept for periodic maintenance and service.
This Daikin unit represents a substantial investment and deserves the attention and care to keep this equipment in good
working order. If the operator observes abnormal or unusual operating conditions, calling Daikin technical service is
recommended.
In any case, it is essential to follow the instructions below during operation and maintenance:
Do not allow unauthorized and/or unskilled personnel to access the unit.
It is forbidden to access the electrical components without having opened the unit main switch and switched off
the power supply.
It is forbidden to access the electrical components without using an insulating platform. Do not access electrical
components if water and/or moisture are present.
Ensure that all operations on the refrigerant circuit and on components under pressure are exclusively carried
out by qualified personnel.
Compressors should only be replaced by qualified personnel.
Sharp edges can cause injuries. Avoid direct contact.
Do not introduce solid objects into the water pipes while the unit is connected to the system.
A mechanical filter must be fitted to the water pipe connected to the heat exchanger inlet.
It is absolutely forbidden to remove any protection system covering moving parts.
In case of sudden stop of the unit, follow the instructions on the Control Panel Operating Manual which is part of the on-
board documentation delivered to the end user.
It is strongly recommended to perform installation and maintenance with other people.
In case of accidental injury or unease, it is necessary to:
Keep calm.
Press the alarm button if present in the installation site.
Immediately contact any emergency personnel in the building or the call the Emergency Services.
Wait until emergency personnel arrive and do not leave the injured person alone.
3.2 Unit description
The machine is made up of a latest generation, high efficiency flooded shell and tube evaporator, with the refrigerant
outside the tubes and the water to be cooled flowing inside the tube..
A shell and tube condenser where the refrigerant condenses outside the tubes while the cooling water flows inside of the
high-efficiency tubes.
An economizer is included in the DZ series XE version. The economizer is a plate exchanger and uses an electronic
expansion valve for each compressor. The algorithm, in the controller, monitors various thermodynamic cycle parameters
to control these valves.
The compressor is a centrifugal type with magnetic bearings and thus does not require lubrication oil. A part of the
refrigerant in the liquid line is used to cool the inverter, thus permitting optimal compressor operations in the foreseen
conditions. Refrigerant flow is controlled by the compressor that continuously monitors inverter temperature.
The compressor, controlled by inverters, changes its cooling load according to the rotational speed decided by the
controller. In this way the machine perfectly adapts to system operating conditions to maximize performance.
The cooling circuit also installs an electronic overflow valve that, in addition to managing the level of refrigerant in the heat
exchangers, guarantees the correct operation of the compressor, keeping it within the foreseen limits.
All the described components are managed by an innovative microprocessor control system that, by monitoring all the
machine operating parameters, optimizes operations. A diagnostic system helps the operator in identifying alarm and fault
causes.
Before starting the compressors ensure that all valves are open and the closing capsare repositioned
and tightened.

D-EIMWC01405-18EN- 20/32
The unit controller is a microprocessor control panel designed to perform compressor start up step by step, monitor and
adjust compressor capacity, protecting it, and perform the shutdown sequence in the absence of load or at a set time. The
control panel provides a wide range of data control and registration capacity options. It is important to have good familiarity
with the control system foroptimal machine operations. Please note that all units are also provided with the Control Manual.
Fig. 6 –Electrical Panel Layout
3.3 Safeties for each cooling compressor
Motor cooling
High compressor delivery temperature
Compressor suction temperature
Failed start
Low pressure
High pressure
Inverter alarm
3.4 System safeties
Antifreeze
Correct phase sequence and phase failure
Evaporator flow switch
3.5 Regulation type
PID regulation (Proportional - Integrative - Derivative) on the evaporator outlet sensor for perfect water temperature
regulation (ΔT = ± 0.3° C).
3.6 Compressor Lead-Lag
The water-cooled Daikin EWWD(H)_ DZ units alternate the compressor start sequence (EWWD(H)_DZ dual compressor)
to balance the number of starts and operating hours. Compressors are automatically alternated by the controller.
If the unit is in automatic mode, the compressor with the lowest number of starts is started first. If both compressors are in
operation and one compressor must be turned off, the one with most hours is switched off
3.7 High condensing pressure control
The microprocessor is provided with a transducer to monitor condensing pressure. Although the main purpose of the high
pressure transducer is to maintain proper control of the condensing pressure (by controlling the cooling towers if
connected), another purpose is to send a signal to the microprocessor which stops the compressor in case the discharge
pressure is excessive. If the unit is switched off for high condensing pressure, the microprocessor must be reset manually.
General door locking
switch handle
User interface
Emergency button
Switches: Unit On/Off