Daikin BRC1E71 User manual

English
Français
Español
Be sure to read this installation manual before
installing this product.
On/Off
Mode
Fan
Speed
Cancel
Menu
OK
MODEL BRC1E71
WIRED REMOTE
CONTROLLER
INSTALLATION MANUAL
Veillez à lire ce manuel d’installation avant
d’installer ce produit.
Asegúrese de leer este manual de instalación
antes de instalar este producto.
00_CV_3P243521-2B.indd 100_CV_3P243521-2B.indd 1 8/27/2009 1:52:57 PM8/27/2009 1:52:57 PM

English 1
Contents
1. Safety Considerations ...................... 2
2. Accessories ....................................... 4
3. Remote controller installation
procedure .......................................... 4
4. Functions and menu items
of remote controller buttons .......... 10
5. Power-on .......................................... 12
6. Field Settings .................................. 13
7. Test Operation ................................. 15
8. Procedure for Checking
Error History .................................... 18
9. Entering Maintenance Contact
Information ...................................... 19
10. Confirmation registered details ..... 20
11. Clock & Calendar ............................ 20
12. Language ......................................... 21
01_EN_3P243521-2B.indd 101_EN_3P243521-2B.indd 1 8/27/2009 2:00:05 PM8/27/2009 2:00:05 PM

2 English
Safety Considerations1.
Read these SAFETY CONSIDERATIONS carefully before installing the remote controller.
After completing the installation, ensure that the unit operates properly during the startup operation.
Train the customer to operate and maintain the unit. Inform customers that they should store this
Installation Manual with the Operation Manual for future reference.
Always use a licensed installer or contractor to install this product. Improper installation can result in
water or refrigerant leakage, electrical shock, fire, or explosion.
Meanings of WARNING, CAUTION, and NOTE Symbols.
WARNING Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTE Indicates situations that may result in equipment or property-damage
accidents only.
WARNING
Only qualified personnel must carry out the installation work.
Consult your Daikin dealer regarding relocation and reinstallation of the remote controller.
Improper installation work may result in leakage, electric shocks or fire.
Install the remote controller in accordance with the instructions in the installation manual.
Improper installation may cause electrical shocks or fire.
Use only specified accessories and parts for installation work.
Failure to use specified parts may result in water leakage, electric shocks, fire, or the unit falling.
Do not disassemble, reconstruct, or repair.
Electric shock or fire may occur.
Make sure that all wiring is secured, that specified wires are used, and that no external forces act on
the terminal connections or wires.
Improper connections or installation may result in fire.
Before touching electrical parts, turn off the unit.
01_EN_3P243521-2B.indd 201_EN_3P243521-2B.indd 2 8/27/2009 2:00:05 PM8/27/2009 2:00:05 PM

English 3
CAUTION
Keep water out of the remote controller.
To avoid leakage and electric shock due to entry of water or insects, fill the wiring through-hole with
putty.
Do not wash the remote controller with water as it may result in electrical shocks or fire.
Do not touch the remote controller buttons with wet fingers.
Touching the buttons with wet fingers can cause an electric shock.
Do not install the remote controller in the following locations:
Where a mineral oil mist or oil spray or vapor is produced, for example, in a kitchen.(a)
Plastic parts may deteriorate and fall off or result in water leakage.
Where corrosive gas, such as sulfurous acid gas, is produced.(b)
Corroding copper pipes or soldered parts may result in refrigerant leakage.
Near machinery emitting electromagnetic waves.(c)
Electromagnetic waves may disturb the operation of the control system and cause the unit to
malfunction.
Where flammable gas may leak, where there is carbon fiber or ignitable dust suspensions in the(d)
air, or where volatile flammables such as thinner or gasoline are handled.
Operating the unit in such conditions can cause a fire.
High temperature area or directly flamed point.(e)
Heating and/or fire can occur.
Moist area, where there is exposure to water. If water enters the inside of the remote controller,(f)
it may cause electric shock and electrical components may fail.
NOTE
Install the control wires for the indoor and the remote controller at least 3.5 feet (1 meter) away from
televisions or radios to prevent image interference or noise. Depending on the radio waves, a
distance of 3.5 feet (1 meter) may not be sufficient to eliminate the noise.
If water enters the inside of the remote controller, electric shock may be caused and inner
electronics may fail.
When remote controller’s thermostat sensor is used, select the installation location as per the
following:
A place where average temperature in the room can be detected.●
A place where it is not exposed to direct sunlight.●
A place where it is far apart from heat source.●
A place where it is not affected by outside air due to door opening/closing.●
01_EN_3P243521-2B.indd 301_EN_3P243521-2B.indd 3 8/27/2009 2:00:06 PM8/27/2009 2:00:06 PM

4 English
Accessories2.
The following accessories are included.
Wood screw Small screw Clamp Operation
manual
Installation
manual Wiring retainer
(φ3.5×16mm) (M4×16mm)
(2 pcs.) (2 pcs.) (1 pc.) (1 pc.) (1 pc.) (1 pc.)
Remote controller installation procedure 3.
Determine where to install the remote controller.3-1
Make sure to follow “ 1. Safety Considerations” when determining the location.
If the control cable for the remote controller is to be routed3-2
from the rear, make a hole in the wall taking into consideration
the location of the access hole in the lower case.
Align the center of the wall
hole with the center of the
access hole on the controller
lower case when planning the
installation.
F5/16-3/8
External view of the remote controller
Access
hole
F5/16-3/8
Lower case
Through hole
1-15/16
1-9/16
Remove upper case.3-3
Insert a screwdriver in the recess of lower case to remove the upper case (2 points).
Upper case
Lower case
Screwdriver
Insert and twist the screwdriver
lightly for removal.
Remote controller PC-board is
installed on the upper case. Take care
not to damage the PC-board with the
screwdriver.
Take care that dust or moisture does
not touch the PC-board.
If the hole size is too large or not in the proper
location, it may be seen after the remote
controller is installed.
NOTE
01_EN_3P243521-2B.indd 401_EN_3P243521-2B.indd 4 8/27/2009 2:00:06 PM8/27/2009 2:00:06 PM

English 5
Determine the location where the cabling will enter the3-4
remote controller (back, left side, top left, top center).
Back outlet3-4-1 Left outlet3-4-2
Cut off resin area (hatched area). Using an appropriate tool, cut the plastic at
the hatched area and remove any remaining
burrs.
Top left outlet3-4-3 Top center outlet3-4-4
Using an appropriate tool, cut the plastic at
the hatched area and remove any remaining
burrs.
Using an appropriate tool, cut the plastic at
the hatched area and remove any remaining
burrs.
Install wiring.3-5
1. Switch box and control wiring are not attached.
Do not touch the remote controller PC-board.2.
NOTE
Wiring Specifications
Wiring Type Non-shielded, 2-conductor, stranded copper cable
Wiring Size AWG-18
Wiring Length Maximum 1640 feet (500m)
01_EN_3P243521-2B.indd 501_EN_3P243521-2B.indd 5 8/27/2009 2:00:08 PM8/27/2009 2:00:08 PM

6 English
Prepare the cabling for connection to the remote controller following these instructions:
Remove the cable jacket
and insulation
Cutting guideline
Approx. 3/8 inch
To simplify the wiring, maintain
a 3/8in difference between the
length of the two conductors.
Length of jacket to be removed:
Approx. 6 inch for top left outlet●
Approx. 8 inch for top center outlet●
Connect the terminals (P/P1, N/P2) of the remote controller to the terminals (P1, P2) of the
indoor unit. (P1 and P2 are not polarity sensitive.)
Back outlet3-5-1
<Cable attachment guideline>
Lower case
P1
Indoor unit
P2
Upper case
PC-board
Clamp
Cable attachment
point
Cross-section -
Secure the cable at
the attachment point
by using furnished
clamping material.
Clamp
01_EN_3P243521-2B.indd 601_EN_3P243521-2B.indd 6 8/27/2009 2:00:09 PM8/27/2009 2:00:09 PM

English 7
Left outlet3-5-2
PC-board
Lower case
Upper case
Indoor unit
P1P2
Top left outlet3-5-3
As shown to the left,
install the attached
retainer to prevent
the wires from being
pinched during
installation.
PC-board
Indoor unit
Wiring retainer
Wiring retainer
Upper case
Lower case
Upper case
Wiring
Cross-section -
P1P2
Top center outlet3-5-4
PC-board
Indoor unit
Wiring retainer
Upper case
Lower case
P1P2
01_EN_3P243521-2B.indd 701_EN_3P243521-2B.indd 7 8/27/2009 2:00:09 PM8/27/2009 2:00:09 PM

8 English
●To prevent electrical noise and possible communication errors, avoid installing the
remote controller cabling parallel to or in the vicinity of line voltage circuits.
NOTE
Installation procedure for the lower case.3-6
When wiring the remote controller through the top center or rear access points, attachment of the
cable to the lower case is required before it is wall mounted. Closely follow the wiring
procedures.
Wall installatoin3-6-1
Secure by using attached wood screws (2 pcs.).
Wood screws
(F3.5×16mm)
Switch box installation3-6-2
Secure by using attached small screws (2 pcs.).
Small screws (M4×16mm)
Switch box
(field supply)
(Use optional accessory
KJB211A)
Switch box for two units
(with no cover)
3-5/16
1-13/16
(Installation pitch)
01_EN_3P243521-2B.indd 801_EN_3P243521-2B.indd 8 8/27/2009 2:00:10 PM8/27/2009 2:00:10 PM

English 9
Switch box
(field supply)
(Use optional accessory
KJB111A)
Small screws (M4×16mm)
Switch box for one unit
(with no cover)
3-15/16
1-1/8
(Installation pitch)
●Install the control on a flat surface only.
To prevent deformation of the lower case, avoid over-tightening the installation screws.●
NOTE
Install the upper case.3-7
Align the upper case with tabs of the lower case (6 points), insert and install the upper case.●
Install the wiring with care to prevent pinching.●
Peel off the protective membrane which overlays the upper case.●
01_EN_3P243521-2B.indd 901_EN_3P243521-2B.indd 9 8/27/2009 2:00:11 PM8/27/2009 2:00:11 PM