damixa TB100541 User manual

FI-CX-B6‐‐1 ‐‐
Damixa Bath Shower Mixers
Product Code – TB100541 - Space bath shower mixer – 2 Handle
TB100641 - Space bath shower mixer – Single Lever
TB110541 - Lyra bath shower mixer – 2 Handle
TB110641 - Lyra bath shower mixer – Single Lever
TB120441 - Ixia bath shower mixer – 2 Handle
TB130541 - Iona bath shower mixer – 2 Handle
TB140241 - Elara bath shower mixer – Single Lever
TB150241 - Clover bath shower mixer – Single Lever
Please retain these instructions for future use and reference.
Fitting Instructions
Introduction
Minimum operating pressure - 0.2 bar – to bath outlet, 0.1 bar for shower outlet
Maximum operating pressure - 5 bar
These mixers are suitable for use on low -pressure or high-pressure systems. For optimum
use both hot and cold pressures should be nominally balanced (equal) and be from a
common source.
These mixers should be installed in accordance with the Water Supply (Water Fittings)
Regulations 1999, with current amendments. For further details contact your Local Water
Authority.
Your attention is drawn to the following installation requirements.

FI-CX-B6‐‐2 ‐‐
Please note these mixers are not thermostatic and the output temperature is dependant
upon prevailing incoming water temperatures and pressures. Always take care when using
hot water, especially with children. Never leave a child unattended.
Pressure Suitability
These mixers have been designed to give high flow rates at low pressures for bath filling.
For high-pressure systems above 1 bar pressure where water consumption is excessive the
mixer is also provided with a Regul8 flow regulator that limits the maximum flow to 8
litres/min (+/- 10%) for the shower. Simply fit to the shower outlet between the shower hose
and the threaded outlet of the mixer. Fit the Regul8 insert with the holes facing the incoming
water stream and the ‘O’ ring facing towards the shower hose as shown below.
Installation
Home Safety Advice
Always take care when using an electric drill, particularly in the bathroom. Always check for
hidden cables and pipework before drilling and take extreme care if there is any water in the
working area.
Always wear suitable eye protection when drilling. Unplug any equipment after use.
Installation
1. Turn off all water and any electrical supplies.
2. Identify all components and check to see if complete before starting installation.
3. Where supplied (Ixia and Iona) place the base shrouds onto the inlet tail of the mixers.
4. Fit any sealing washers or gaskets to the mixer and then fit the mixer into the tap holes in the
bath.
5. Fit the metal back nuts onto the tap tails and tighten fully until the mixer is secure.
6. Connect the taps to hot and cold supplies. Isolating valves should be fitted to hot and cold
supply pipes.
7. Fit the waste (not supplied) to the bath.

FI-CX-B6‐‐3 ‐‐
8. Fit the shower hose to the outlet of the shower. NOTE: If required fit the Regul8 regulator as
described previously.
9. Fit the hand shower bracket supplied taking care when drilling walls that electrical or water
supplies are clear of any holes drilled.
10. Turn on the water supplies and check there are no leaks in any of the connections.
11. Operate the mixer and check flow. It may be necessary to remove the flow straightener to
ensure any swarf in the new plumbing is flushed away.
12. Check the diverter to switch to shower. Note: Ixia and Iona use a manual diverter that needs
to be switched back to bath fill mode after every shower use. Space, Lyra, Elara and Clover
feature a diverter that returns automatically.
Aftercare Instructions
Damixa products have a high quality surface and should be treated with care to maintain the
surface finish.
To clean simply wipe with a soft damp cloth with a mild detergent applied. Dry with a soft
cloth. Do not use chemical or household cleansers as these may cause staining, abrasive
agents will scratch the surface.
Guarantee
Damixa guarantees quality and reliability. All products are manufactured to the highest
standards using the latest production technologies. We guarantee the product for 5 years
from date of purchase against manufacturing defects.
This guarantee covers all products that have been used in the manner they were intended
and does not apply to products that have been incorrectly installed, misused or abused in
any way.
In the unlikely event that a Damixa product is found to be faulty we will offer a free
replacement part or product.
This guarantee does not affect your statutory rights.
In the interest of continual product development we reserve the right to alter product
specification where necessary or appropriate.
Please contact Croydex Ltd at the address below for any advice or help.
Croydex Ltd
Central Way
Andover, Hampshire, SP10 5AW
Tel [phone]
Fax [phone]
Sales: [email protected]
Helpline: [email protected]
www.damixa.co.uk