Dancing Wings Hobby K9 Mini Spacewalker User manual

A
A
C
D
E
FG1
G2
P1
P2 Q
R
G3
H
I
B1 B2
J
J
K1 K2
K3
L
L
M
N
K4
O
a
b
cd
e
f
g
h
ij
kl m n
opqr
拼装步骤
Installation Steps
机身组装 Fuselage installation
Op
1
2glq
3
K1
d
a
M
EH
B2
n
f
e
5 6
7 8
9
11
12
13
14
15
4
o
切下
cut
Q
自攻螺丝
10 L
J
J
K4
K3
N
B1
K2
j
用刀切下
Cut off with knife
粘贴K2时用少量水
湿润，方便弯曲。
安装磁铁，2个
磁铁为相吸状
A
D
机翼组装
Wing installation
K9 Mini Spacewalker BALSAWOOD AIRPLANE INSTRUCTION MANUAL
粘贴K1时用少量水
湿润，方便弯曲。
Moisten K1 with a little
water when you stick it,
for easy bending.
Moisten K2 with a little water
when you stick it, for easy
bending.
Self-tapping screw
在如图位置安
装自攻螺丝，
可以固定住起
落架Q。装好
后，起落架可
先取下方便后
续拼装。
Install self-tapping
screw as shown,
fasten landing
gear Q.
You can take
down the landing
gear after
installation,
convenient for
your following
installation.
Install magnets, the
2pcs magnets are
attracted each other.
用美工刀从板材下取下各部件，然后
参照以下说明步骤拼装，各部件用
502粘合。
Pls take down the parts from the
board by knife,and assemble them
as per the procedures as below,we
suggest you to stick with 502 glue.

CG≈28mm
C
I
h
粘贴 Stick
G1 G1
G1
G1
G2
G1 G1 G2 G2
G3 G3 r r r r
rG3
k
PVC风挡
PVC windshield
P2
P2
P1
i
m
m
m
m
16
17
18
19
20
21
22
23
24
25
26
27
尾翼组装 Tail-wing installation 马达座，马达组装 Motor mounting board, motor installation
舵角安装 Rudder angle installation
舵机，连杆安装
Servo, link rod installation
起落架及机轮组装
Landing gear and wheels installation
热缩套管
Heatshrink Tube
舵机如下图位置安装到机身内，并把舵臂、
舵角通过连杆连接，短连杆连接副翼，长连
杆连接升级舵，与转向舵。
Install servos into the fuselage as
shown, and connect rudder arm and
rudder angle through link rod.
The short link rod connects aileron, the
long link rods connect elevator and
rudder.
安装调试完电子设备后，可盖上
仓盖。
Install and adjust electric power
system, then cover the cabin.
短连杆
Short link rod
长连杆
Long link rod
热缩套管
Heatshrink Tube
热缩套管
Heatshrink Tube
热缩套管
热缩套管
碳杆
Carbon rod
Carbon rod
碳杆
28
Specification
Wingspan:460mm
Length:380mm
Flying Weight:≈30-35g
Motor:1104 KV3700
ESC:1S 5A
Servo:1.7g servoX3
Prop:4530-5030
BATT:1S 200-250mAh
Radio≥4CH
推荐参数
翼展:460mm
机长:380mm
起飞重量:≈30-35g
马达:1104 KV3700
电调:1S 5A
舵机:1.7g servoX3
桨叶:4530-5030
电池:1S 200-250mAh
通道≥4CH
完成后喷黑漆
Spray black paint
after finished.
Heatshrink Tube
Heatshrink Tube
29