Dancover San Pablo PA153020 User manual

13-01-2021
for
Gazebo San Pablo
3x5,8m and 4x5,8m
Manual

Manual Instruction

Parts list table
Label
No. Part Description Drawing Qty
A1 Column I 4
A3 Middle
column 2
B1 Beam (Left) 1
B2 Beam (Right) 1
C1 Front and
rear beam I 2
C2 Front and
rear beam II 2
D1 Middle beam
with gear box 2
D2 Middle beam 1
E Louver
6*3=88
8*3=88
6*4=120
8*4=120
F Column
bottom plate
4
G Column
cover plate
4
H
Connectors
for
middle
beams
6

Parts list table
Label
No. Part Description Drawing Qty
I Hinge ring 4
J Hand crank 2
K1
Hexagon
socket
countersunk
head screw
76
K2 Hexagon socket button
head screws
42
K3 Flat washer 24
K4
Cross
recessed pan
head screw +
nut
4
K5 Flat washer 24
L
Wooden
screw+ Plastic
expansion
pipe K3
M Glass glue 1
N Plastic plug
6x3=176
8x3=176
6x4=240
8x4=240
O Cover plate for
middle beam
2
PDrainage
connector
(Optional)
6
QBottom plate
for middle
column
2

Optional: P
STEP 1:
Clamp the drainage connector
P into the column slot.
STEP 2:
Fix the bottom plate F to the
column A1/A3 with screws K1.
Column A1
Middle Column A3

Fix the column bottom plate F and Q to the
column A1/A3 with the screws K1.
Column A1
Middle Column A3
Bottom
Plate F
Bottom
Plate Q

STEP 1:
Fix the connector to
the middle beam D1,
D2 with screws K1.
STEP 2:
Insert the hinge ring I
into the gearbox shaft
and fix it with screw
and nut K4.
Column A1
Column A1
Middle Column A3
Column A1
Middle Column A3
Column A1
Outlet 2
Outlet 1
Outlet 6
Outlet 4
Outlet 3
Outlet 5
STEP 3：
Place the column as shown in the figure below.
Middle beam D1
Middle beam D2

Beam B1
Insert the beam B1 into the column A1
and fix it with screws K1.
Column A1
Column A1

Beam B2
STEP 1:
Insert the beam C1 into the column
A1, A3 and fix it with the screw K1.
Column A1
Middle Column A3
Beam C1
STEP 2:
Fix the columns to the beams with
screws K1 as the figure below.
Middle column A3
Middle Column A3
Column A1
Column A1
Column A1
Column A1
Beam C1
Beam C2
Beam C1
Beam C2
Beam B1

STEP 1:
Fix the cover plate G to the columns
and beams with screws K2 as the
figure below.
STEP 2:
Fix the cover plate O to the columns
and beams with screws K2 and K1
as the figure below.
Screws
K1

STEP 1:
Adjust the position of 6 columns to keep them perpendicular to the ground.
Meanwhile, the width of the top of each two columns should be measured in
accordance with the width of the bottom of each two columns. Then use a market pen
to mark 24 holes on the ground, which should be corresponding to the holes in the
bottom plate.
Mark the position of the
hole on the ground with
a mark pen

STEP 1:
Remove the product from the mark and drill
holes of ∅10X80 at 24 mark positions on the
ground with a percussion drill.
STEP 2:
Place the plastic expansion pipe in the bottom hole of the column;
then move the product back to the hole drilled, align holes of the
column bottom plates with the hole drilled on the ground; then set
K5 into the wooden screw L and fix it with the ground separately.
Drill depth:
∅10x80
Drill qty:
24pcs

STEP 1:
Coat the glass glue M evenly around 6
drain of column and joints of beams.
STEP 2:
Place the middle beams D1/D2 on
the front and rear beams C1/C2.
Beam C2
Beam C1
Beam C2
Beam C1
Middle beam D1
Middle beam D1
Middle beam D2

STEP 1:
As shown in the figure below, clip
the louver E into the tail of the
bracket of the beams at both ends
first, then press down the louver
to make it clamp and install in the
direction indicated by the arrow at
the position 1 and 2 respectively.
Louver E
1
2
1
2
Install the first two
louvers at each head

STEP 1:
Align and fix the hole under
D1/D2 with screws K2 and
washer K3; then Align and fix
the hole on the C1/C2;
Install the remain louvers in
turn.
Beam D1
Beam C1
Beam C2
Beam C1
Beam C2
Beam D1
Beam D2

If the holes are not
aligned as figure
below, adjustments
will be required
Insert a straight
screwdriver into position 1
and move the louver
supporter according to
direction 2 to make holes
concentric
Holes are concentric
after adjusting
1
2

The plastic jam installed at
the front fixed louver
STEP 1:
Insert plastic N jam into holes at two
ends of the louvers.

STEP 1:
Put the hand crank J on, turn to open/close the louvers;
installation completed.

I
For more information
please visit:
www.dancovershop.com
l
l
l
l
l
l
l
l
l
l
l
Dancover A/S
Lyngevej 16A, Nørre Herlev
3400 Hillerød
Denmark
Head office: