Dancover San Pablo User manual

12-07-2023
Manual
for
Gazebo San Pablo
3x5,8m and 4x5,8m

Manual Instruction

Parts list Table
Label No.
Part description
Drawing
Qty
Column I
Column II
Beam (Left)
Beam(Right)
Front and rear
beam I
Front and rear
beam II
Middle beam
with gear box
Middle beam
Louver
Column bottom
plate
Column cover
plate
Connectors for
middle beams
Hinge ring
Hand crank
A3

Label No.
Part description
Drawing Qty
Countersunk
head screw
Pan head
screw
Flat washer
Screw+nut
Flat washer
Self-drilling
screw
Woodworking screw+ plastic
expansion pipe
Glass glue
Plastic jam
Cover plate
for middle
column
Bottom plate
for middle
column
Corner support
48
O
p Drainage
outlet 6
8
sScrew cover
24
Please Note: R and K6 is an optional..., if you do need install them,
please refer to the last pages first.
The R and K6 should be removed if you need to install the screen set.

．． • •I• •
Al
. 
 
F  
 亿 
A3

| 

 
）
  

Kl
1. Clamp the drainage outlet P
into the column slot, then
connect the bottom plate F/Q
on the column A1/A3, and
tighten with K1 screws.

01�
Kl 诩·M6X16
QTY: 24PCS
step 1
/H
H卢QTY:6PCS
Page 2
2. Place the connector H on one side of middle beam D1/D2,
then tighten it with K1 screws; complete the other side of middle beam D1/D2
accordingly.
Complete three beams with connector H accordingly

DI/
step 1

匾
step 2
  ®飞勹
Page 3
3. Put two hinge rings I into the gearbox drive shaft on the beams D1,
then tighten them with K4 screws + nuts.


 
 


 
 
Page 4
4. Place the columns and beams as shown in the below drawing

Kl

step 1

．．
诩M6X16


step 2
A3
••

Page 5
5. The two ends of the front and rear beam C1 must be inserted into the corner connectors
of columns A1 and A3; then tighten them with K1 screws.

Kl 闷M6X16
Bl
A3
QTY: 4PCS
Page 6
6. In the same way, the ends of left and right beams B1 must be inserted into the corner
connectors of the column A1, then tighten them with K1 screws.
A1

Kl 闷M6X16 QTY:16PCS
Page 7
7. According to the step 5 and 6, insert other beams with the corner connector of columns,
then tighten them with K1 screws.

§



G

Kl

step 2
 淑
QTY: 4PCS  严QTY:18PCS

＜QTY: 4PCS 。气QTY: 2PCS
Page 8
8.The 4 column cover plates G and middle column cover plate P must be mounted on top of the
corner connectors of the columns and
beams, then tighten them
with K2 and K1 screws.

肋
K6 @咖仁
ST4.2x25
QTY: 48PCS R乏］QTY:12PCS
Page 9
9. Align the corner supporter R with the bottom
the bottom edge of the beam B1, edge of the beam, fix it with self-drilling screw
K6. Install the remaining corner supports in turn
under each of the beams.
Please note: The corner supporters should be
removed if one side need to be installed
screen.

Use tools: marker pen (self-provided)
／
Page 10
10. Adjust the position of the six columns so that they are perpendicular to the ground.
Also check that the distance between each two columns is the same on both the top and
in accordance with the width of the bottom of each two columns.the bottom. Then use a marker pen to dot 24 holes on the ground, which must correspond
to the holes in the column bottom plates.
Mark the location of the hole
on the ground with
a marker pen

．．言
/
 
11. Remove the product aside from the marks you just made on the ground. Drill holes
at 16 mark positions on the ground with a percussion drill.of 10x80mm in the ground at all 24 marks, using a percussion drill.
Drilling depth 10x80
Drilling quantity 24pcs
Use Tools: Percussion Drill
(Self-provided)
Use Tool: Percussion Bit 10
(Self-provided)

5
RL
K
@
叭8
QTY: 24PCS
Page 12
12. Place the plastic expansion pipes into the holes drilled in the ground.
Reposition the product on top of the drilled holes in the ground and make sure to perfectly
match the holes in the column bottom plates with the holes in the ground; then set the flat
washers K5 into woodworking screws L and fix them in the ground one by one.
Then put on screw cover S.
K5
L
s
QTY: 24PCS
QTY: 24PCS

M
MQTY: 2PCS
Page 13
13.Coat the glass glue M evenly on the drain of columns and joints of beams.

Cl


Cl/
Page 14
14.Place the middle beam D1/D2 onto the front and rear beams C1/C2.

EE
EE
Page 15
15.As shown in below figure, Insert louver E at the end of the brackets of at both side of the
on the end of the brackets on both sides of the beams (B1-D and B2-D),beams first, then press down the louver to make it clamp and install in the direction by the
arrow at the position 1 and 2 respectively. Insert louvers according to the position of below
drawing (total eight louvers at gear box side, 4pcs louvers at the other side)

Astep 2
K2 严QTY: 24PCS K3 ｀ QTY: 24PCS
Page 16
16. Set the flat washers K3 into
the screws K2 at first, fix them
into the holes below beam D1/
D2, then align the screws K2
with flat washers with the holes
on the top of the beam C1/C2
and tighten it. Install the other
louvers in turn.