Dancover B788 User manual

2,7x5,1x2,3m
Garage tent
Manual
21-04-2015-QJ

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is
your responsibility to comply with local rules and regulations and to ensure that the
marquee/tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is
safely secured and that the marquee/tent does not cause damage to others.
close to the tent.
The marquee/tent must be safely secured. We recommend you secure your marquee/tent
with straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents
insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow always remove snow from the roof of the marquee/tent regularly to
prevent snow from building on the roof as heavy snow can cause the marquee/tent to
collapse.
In the event of rain there is a risk of rain puddles building up on top of the roof of the
marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility
to ensure rain puddles do not build up. As a precaution, make sure the roof of the
marquee/tent is stretched out properly and adequately over the side frames of the
marquee/tent and remove rain water regularly.
Do not unpack or repack your marquee/tent in freezing temperatures. In case of
temperatures below zero always unpack and repack your marquee/tent indoors to avoid
the risk of cracking parts.
The marquee/tent must be totally dry before you repack and store it to avoid mildew.
Warranty Information
Please visit dancovershop.com for information on warranty.
Maintenance: You must regularly check and retighten all assembly points of your storage shelter
or garage tent. It is especially important to retighten the roof cover 1 month after having erected
your shelter or tent. The roof cover of your shelter or tent must always be tensioned to withstand
wind and weather.
Please always check our website for the latest safety advice and manuall.

Packing List of Model B788 (2.7*5.1*2.3M）
Part
Code
Description Quantity Box
1Top roof curved tube
5
2 Roof curved tube
10
3Sidewall tube
6
3A Sidewall tube at front and rear
4
4 Roof purlin an horizontal tube
9
4A Roof purlin and horizontal
tube
3
5
5A
Cross bar
Cross bar
2
3
6Wind brace
Wind brace
support tube
2
6A Tube slip for
standing support tube
14
7 Tension at the bottom of the
tube
2sets
7A At the bottom end tighten
tube
4
8 Stake peg
20
21-04-2015-QJ

8A Tube clip
10
9 M6 * 65 ball stud
25
10 M6*40 hex bolt
12
11 M6*25 hex bolt
16
12 M6*40 hex bolt
4
13 Plastic cap for tensioning tube
16
14 Lace rope for roof cover front
cover rear cover
40m
15 S hook
8
16 The S hook rope of the door
4
17 Roof cover
1
18 Door cover
1
19 Back cover
1
21-04-2015-QJ

1
2
3A
3
5
67
7A
14
9
10
5A
2
2
2
2
4
4A
8
8A
7
7A
7
7
5A
5A
5
4
6
7A 7A
8A
8
8A
8
8A
8
4A
4A
3A
3A
3A
3
3
3
3
3
8A
8
6
6A
11
6A 5
11
4
4
4
4/4A
2
2
3/3A

6A
6A
/5A

part 11
(part 9)
4
4
3A
3
4
5
5A

Step #4--POSITION ROOF COVER
As figure 8shows, when ready to install Roof Cover, unpack cover and lay parallel to building
frame on one side. Cover must be pulled over top of frame assembly without being snagged or
stressed on any frame parts. Use multiple ropes over top of frame as shown in picture below.
Having another person inside frame on a ladder to assist in getting Roof Cover over frame will
insure the cover will go on without any damage.

Figure 7 Hang Door
cover with S-hooks on
part 5. Close the door
with the zipper.
Fasten the door and
the roof cover to the
frame.
Figure 9 open door cover
Use part 16 to keep
door open
Figure 8 Fasten the
endwall and the roof
cover to the frame.
Use rope (part 14)