Danfoss AK-PC 772A User manual

Capacity controller
for small CO2refrigeration system
AK-PC 772A
User Guide
ADAP-KOOL®Refrigeration control systems

2 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
Contents
1. Introduction.............................................................................3
Application.................................................................................................. 3
Principles...................................................................................................... 4
2. Design of a controller..............................................................7
Module survey ........................................................................................... 8
Common data for modules.................................................................10
Controller ...........................................................................................12
Extension module AK-XM 101A.................................................14
Extension module AK-XM 102A / AK-XM 102B.....................16
Extension module AK-XM 103A.................................................18
Extension module AK-XM 204A / AK-XM 204B.....................20
Extension module AK-XM 205A / AK-XM 205B.....................22
Extension module AK-XM 208C................................................24
Extension module AK-OB 110 ....................................................26
Extension module EKA 163B / EKA 164B / EKA 166............27
Graphic display MMIGRS2............................................................27
Power supply module AK-PS 075 / 150 / 250........................28
Communication module AK-CM 102.......................................29
Preface to design ....................................................................................30
Functions............................................................................................30
Connections......................................................................................31
Limitations.........................................................................................31
Design of a compressor and condenser control .........................32
Procedure:..........................................................................................32
Sketch..................................................................................................32
Compressor and condenser functions....................................32
Connections......................................................................................33
Planning table ..................................................................................35
Length.................................................................................................36
Linking of modules.........................................................................36
Determine the connection points ............................................37
Connection diagram......................................................................38
Supply voltage ................................................................................40
Ordering.....................................................................................................41
3. Mounting and wiring.............................................................43
Mounting...................................................................................................44
Mounting of analog output module........................................44
Mounting of extension module on the basic module.......45
Wiring..........................................................................................................46
4. Configuration and operation................................................49
Configuration...........................................................................................50
Connect PC........................................................................................50
Authorization....................................................................................52
Unlock the configuration of the controllers..........................53
System setup ....................................................................................54
Set plant type ...................................................................................55
Set control of MT compressors...................................................56
Set control of LT compressors.....................................................60
Setup control of condenser fans ...............................................61
Setup control of high pressure...................................................63
Setup control of receiver pressure............................................64
Setup control of heat recovery..................................................65
Setup Display....................................................................................66
Setup Functions for General purpose......................................67
Separate thermostat...............................................................68
Separate pressostat ................................................................68
Separate voltage signal.........................................................69
Separate alarm inputs............................................................69
Separate PI function ...............................................................70
Configuration of inputs and outputs.......................................71
Set alarm priorities..........................................................................73
Lock configuration..........................................................................75
Check configuration.......................................................................76
Check of connections............................................................................78
Check of settings.....................................................................................80
Schedule function ..................................................................................82
Installation in network..........................................................................83
First start of control................................................................................84
Start the control...............................................................................85
Manual capacity control...............................................................86
5. Regulating functions.............................................................87
Suction groups ........................................................................................88
Controlling sensor...........................................................................88
Reference ...........................................................................................88
Capacity control of compressors...............................................89
Capacity distribution methods...........................................90
Power pack types – compressor combinations............91
Compressor timers..................................................................95
Compressor with variable capacity...................................96
Load shedding..........................................................................97
Injection ON ..............................................................................97
Liquid injection in common suction line ........................98
Safety functions...............................................................................98
Condenser / Gas cooler ......................................................................100
Capacity control of condenser.................................................100
Reference for condensing pressure........................................100
Heat recovery .................................................................................102
Capacity distribution ...................................................................104
EC motor...........................................................................................104
Step regulation.......................................................................104
Speed regulation ...................................................................104
Condenser couplings...........................................................105
Safety functions for condenser.........................................105
Circuits for control of CO2 gas pressure................................106
Receiver control .....................................................................107
Parallel compression ............................................................108
General monitoring functions .........................................................109
Miscellaneous ........................................................................................111
Appendix - Alarm texts.......................................................................116

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 3
Application
AK-PC 772A is complete regulating units for capacity control of
compressors and gas cooler in a small CO2refrigeration systems.
Either as a compressor and condenser control on MT or as a boost-
er system. There can be regulated with one parallel compressor.
The controller is with oil management, heat recovery function and
CO2gas pressure control.
In addition to capacity control the controllers can give signals to
other controllers about the operating condition, e.g. forced clos-
ing of expansion valves, alarm signals and alarm messages.
The controller’s main function is to control compressors and gas
cooler so that operation all the time takes place at the energy-
optimum pressure conditions. Both suction pressure and gas
pressure are controlled by signals from pressure transmitters and
temperature sensors.
Among the different functions are:
- Capacity control of up to 3 compressors on high pressure
(2 if also regulating with parallel compressor).
- Capacity control of up to 2 compressors on low pressure
- Up to 3 unloaders for each compressor
- Speed control of one or two compressors
- Up to 6 safety inputs for each compressor
- Option for capacity limitation to minimize consumption peaks
- When the compressor does not start, signals can be transmitted
to other controllers so that the electronic expansion valves will
be closed
- Control of liquid injection into suction line
- Safety monitoring of high pressure / low pressure / discharge
temperature
- Capacity control of up to 4 fans
- Floating gas cooler reference with regard to outside temperature
- Heat recovery function
- CO2gas cooler control and receiver control
- Parallel compression on transcritical CO2system
- Step coupling, speed regulation or a combination
- Safety monitoring of fans
- The status of the outputs and inputs is shown by means of light-
emitting diodes on the front panel
- Alarm signals can be generated via data communication
- Alarms are shown with texts so that the cause of the alarm is
easy to see.
- Plus some completely separate functions that are totally inde-
pendent of the regulation – such as alarm, thermostat, pressure
and PI-regulating functions.
1. Introduction
SW=1.3x

4 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
Principles
The great advantage of this series of controllers is that it can be
extended as the size of the plant is increased. It has been devel-
oped for refrigeration control systems, but not for any specific
application – variation is created through the read-in software and
the way you choose to define the connections.
It is the same modules that are used for each regulation and the
composition can be changed, as required. With these modules
(building blocks) it is possible to create a multitude of various
kinds of regulations. But it is you who must help adjusting the
regulation to the actual needs – these instructions will assist you
to find your way through all the questions so that the regulation
can be defined and the connections made.
Advantages
• The controller’s size can “grow” as systems grow
• The software can be set for one or more regulations
• Several regulations with the same components
• Extension-friendly when systems requirements are changed
• Flexible concept:
- Controller series with common construction
- One principle – many regulation uses
- modules are selected for the actual connection requirements
- The same modules are used from regulation to regulation.
Controller
Top part
Extension modules
A regulation with few connections can
be performed with the controller module
alone
If there are many connections one or more exten-
sion modules have to be mounted
If the system grows and more functions have to be controlled, the regulation can be
extended.
With extra modules more signals can be received and more relays cut in and out –
how many of them – and which – is determined by the relevant application.
Bottom part
The controller is the cornerstone of the regulation. The module has inputs and
outputs capable of handling small systems.
• The bottom part – and hence the terminals – are the same for all controller types.
• The top part contains the intelligence with software. This unit will vary according
to controller type. But it will always be supplied together with the bottom part.
• In addition to the software the top part is provided with connections for data
communication and address setting.
Examples

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 5
Direct connection
Setup and operation of an AK controller must be accomplished via
the “AK-Service Tool” software program.
The program is installed on a PC, and setup and operation of
the various functions are carried out via the controller’s menu
displays.
Displays
The menu displays are dynamic, so that different settings in one
menu will result in different setting possibilities in other menus.
A simple application with few connections will give a setup with
few settings.
A corresponding application with many connections will give a
setup with many settings.
From the overview display there is access to further displays for
the compressor regulation and the condenser regulation.
At the bottom of the display there is access to a number of general
functions, such as “time table”, “manual operation”, “log function”,
“alarms”, and “service” (configuration).
Network linking
The controller can be linked up into a network together with other
controllers in an ADAP-KOOL® refrigeration control system. After
the setup operation can be performed at a distance with, say, our
software program type AKM.
Users
The controller comes supplied with several languages, one of
which can be selected and employed by the user. If there are sev-
eral users, they may each have their choice of language. All users
must be assigned a user profile which either gives access to full
operation or gradually limits the operation to the lowest level that
only allows you“to see”.
Language selection is part of the service tool settings.
If the language selection is not available in the service tool for the
current regulator, English texts will be displayed.
External display
An external display can be fitted in order for P0 (Suction) and Pc
(Condensing) readings to be displayed.
A total of 4 displays can be fitted and with one setting it is pos-
sible to choose between the following readings: suction pressure,
suction pressure in temperature, Ss, Sd, condenser pressure, con-
denser pressure in temperature, gas cooler temperature, etc.
A graphical display with control buttons can also be fitted.

6 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
■Power
■Comm
■DO1 ■Status
■DO2 ■Service Tool
■DO3 ■LON
■DO4 ■I/O Extension
■DO5 ■Alarm
■DO6
■DO7 ■Display
■DO8 ■Service Pin
Slow flash = OK
Quick flash = answer from gateway
Constantly ON = error
Constantly OFF = error
Flash = active alarm/not cancelled
Constant ON = Active alarm/cancelled
Light-emitting diodes
A number of light-emitting diodes makes it possible to follow the
signals that are received and transmitted by the controller.
Log
From the log function you can define the measurements you wish
to be shown.
The collected values can be printed, or you may export them to a
file. You can open the file in Excel.
If you are in a service situation you can show measurements in a
trend function. The measurements are then made real-time and
displayed instantly.
Alarm
The display gives you an overview of all active alarms. If you wish
to confirm that you have seen the alarm you can cross it off in the
acknowledge field.
If you want to know more about a current alarm you can click on it
and obtain an information display on the screen.
A corresponding display exists for all earlier alarms. Here you can
upload information if you need further details about the alarm
history.

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 7
2. Design of a controller
This section describes how the controller is designed.
The controller in the system is based on a uniform connection
platform where any deviations from regulation to regulation is
determined by the used top part with a specific software and
by which input and output signals the relevant application will
require. If it is an application with few connections, the controller
module (top part with belonging bottom part) may be sufficient.
If it is an application with many connections it will be necessary to
use the controller module plus one or more extension modules.
This section will give you a survey of possible connections plus
assistance in selecting the modules required by your actual ap-
plication.

8 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
Extension module with ad-
ditional analog inputs
Extension module with addi-
tional relay outputs and additional
analog inputs.
The module with additional relay outputs is
also available in a version where the top part
is provided with change-over switches so
that the relays can be overridden.
Extension module with
2x analog output signals
Top part
Controller with analog inputs and
relay outputs.
External display for
suction pressure etc.
Bottom part
Module survey
• Controller module – capable of handling minor plant require-
ments.
• Extension modules. When the complexity becomes greater
and additional inputs or outputs are required, modules can be
attached to the controller. A plug on the side of the module will
transmit the supply voltage and data communication between
the modules.
• Top part
The upper part of the controller module contains the intelli-
gence. This is the unit where the regulation is defined and where
data communication is connected to other controllers in a big-
ger network.
• Connection types
There are various types of inputs and outputs. One type may, for
example, receive signals from sensors and switches, another may
receive a voltage signal, and a third type may be outputs with
relays etc. The individual types are shown in the table below.
• Optional connection
When a regulation is planned (set up) it will generate a need for
a number of connections distributed on the mentioned types.
This connection must then be made on either the controller
module or an extension module. The only thing to be observed
is that the types must not be mixed (an analog input signal must
for instance not be connected to a digital input).
• Programming of connections
The controller must know where you connect the individual
input and output signals. This takes place in a later configura-
tion where each individual connection is defined based on the
following principle:
- to which module
- at which point (”terminals”)
- what is connected (e.g. pressure transmitter/type/
pressure range).
If the row of modules needs to
be interrupted due to length or
external positioning, a communi-
cation module should be used.

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 9
Type Analog
inputs
On/Off outputs On/off supply voltage
(DI signal)
Analog
outputs
Stepper
output
Module with
switches
For sensors, pres-
sure transmitters
etc.
Relay
(SPDT)
Solid state Low voltage
(max. 80 V)
High voltage
(max. 260 V)
0-10 V d.c. For valves
with step
control
For override of
relay outputs
Controller 11 4 4 - - - -
Extension modules
AK-XM 101A 8
AK-XM 102A 8
AK-XM 102B 8
AK-XM 103A 4 4
AK-XM 204A 8
AK-XM 204B 8 x
AK-XM 205A 8 8
AK-XM 205B 8 8 x
AK-XM 208C 8 4
The following extension module can be placed on the PC board in the controller module.
There is only room for one module.
AK-OB 110 2
Type Function Application
Operation
AK-ST 500 Software for operation of AK controllers AK-operation
- Cable between PC and AK controller USB A-B (standard IT cable)
Accessories Power supply module 230 V / 115 V to 24 V d.c.
AK-PS 075 18 VA
Supply for controllerAK-PS 150 36 VA
AK-PS 250 60 VA
Accessories External display that can be connected to the controller module. For showing, say, the suction pressure
EKA 163B Display
EKA 164B Display with operation buttons
EKA 166 Display with operation buttons and LED for function cut in
MMIGRS2 Graphic display with operation
-Cable between display and controller Length = 2 m, 6 m
Cable between graphic display and controller Length = 1.5 m, 3 m
Accessories Communication modules for controllers where modules cannot be connected continuously
AK-CM 102 Communication module Data communication for external extension
modules
Type Function Application
AK-PC 772A
Controller for capacity control of a small CO2 plant with booster.
A maximum of 3 compressors for high pressure, 2 for low pressure,
4 fans and a maximum of 120 inputs/outputs
Transcritical CO2 Booster control. Parallel com-
pression /Heat recovery / CO 2 gas pressure
1. Controller
2. Extension modules and survey of inputs and outputs
3. AK operation and accessories
On the following pages there is data specific to each module.

10 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
Common data for modules
Supply voltage 24 V d.c./a.c. +/- 20%
Power consumption AK-__ (controller) 8 VA
AK-XM 101, 102, 107, AK-CM 102 2 VA
AK-XM 204, 205, 208 5 VA
Analog inputs Pt 1000 ohm /0°C Resolution: 0.1°C
Accuracy: +/- 0.5°C
+/- 0,5°C between -50°C and +50°C
+/- 1°C between -100°C and -50°C
+/- 1°C between +50°C and +130°C
Pressure transmitter type AKS 32R / AKS
2050
AKS 32 (1-5 V)
Resolution:1 mV
Accuracy +/- 10 mV
Max. connection of 5 pressure transmitters on one module
Other pressure transmitter:
Ratiometric signal
Min. and Max. pressure must be set
Voltage signal 0-10 V
Contact function (On/Off ) On at R < 20 ohm
Off at R > 2K ohm
(Gold -plated contacts not necessary)
On/off supply voltage inputs Low voltage
0 / 80 V a.c./d.c.
Off: U < 2 V
On: U > 10 V
High voltage
0 / 260 V a.c.
Off: U < 24 V
On: U > 80 V
Relay outputs
SPDT
AC-1 (ohmic) 4 A
AC-15 (inductive) 3 A
UMin. 24 V
Max. 230 V
Low and high voltage must not be connected to the same
output group
Solid state outputs Can be used for loads that are cut in and
out frequently, e.g. :
Fans and AKV valves
Max. 240 V a.c. , Min. 48 V a.c.
Max. 0,5 A,
Leak < 1 mA
Max. 1 AKV
Stepper outputs Used for valves with stepper input 20-500 step/s
Separate supply to stepper outputs : 24 a.c./d.c. / xx VA
Ambient temperature During transport -40 to 70°C
During operation -20 to 55°C ,
0 to 95% RH (non condensing)
No shock influences / vibrations
Enclosure Material PC / ABS
Density IP10 , VBG 4
Mounting For mounting on panel wall or DIN rail
Weight with screw terminals Modules in 100- / 200- / controller-series Ca. 200 g / 500 g / 600 g
Approvals EU low voltage directive and EMC require-
ments are complied with
LVD tested according to EN 60730
EMC tested
Immunity according to EN 61000-6-2
Emission according to EN 61000-6-3
UL 873, UL file number: E166834 for XM and CM-modules
UL file number: E31024 for PC-modules
The mentioned data applies to all modules.
If data is specific, this is mentioned together with the module in question.

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 11
Dimensions
The module dimension is 72 mm.
Modules in the 100-series consist of one
module
Modules in the 200-series consist of two
modules
Controllers consist of three modules
The length of an aggregate unit = n x 72 + 8

12 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
Controller
Function
There are several controllers in the series. The function is deter-
mined by the programmed software, but outwardly the control-
lers are identical – they all have the same connection possibilities:
11 analog inputs for sensors, pressure transmitters, voltage signals
and contact signals.
8 digital outputs, with 4 Solid state outputs and 4 relay outputs
Supply voltage
24 V a.c. or d.c. to be connected to the controller.
The 24 V must not be retransmitted and used by other control-
lers as it is not galvanically separated from inputs and outputs. In
other words, you must use a transformer for each controller. Class
II is required. The terminals must not be earthed.
The supply voltage to any extension modules is transmitted via
the plug on the right-hand side.
The size of the transformer is determined by the power require-
ment of the total number of modules.
The supply voltage to a pressure transmitter can be taken either
from the 5 V output or from the 12 V output depending on trans-
mitter type.
Data communication
If the controller is to be included in a system, communication
must take place via the LON connection.
The installation has to be made as mentioned in the separate
instructions for LON communication.
Address setting
When the controller is connected to a gateway type AKA 245,
the controller’s address must be set between 1 and 119. (If it is a
system manager AK-SM .., then 1-999).
Service PIN
When the controller is connected to the data communication
cable the gateway must have knowledge of the new controller.
This is obtained by pushing the key PIN. The LED“Status”will flash
when the gateway sends an acceptance message.
Operation
The configuration operation of the controller must take place
from the software program“Service Tool”. The program must be
installed on a PC, and the PC must be connected to the controller
via the USB-B plug on the front of the unit.
Light-emitting diodes
There are two rows with LED’s. They mean:
Left row:
• Voltage supply to the controller
• Communication active with the bottom PC board (red = error)
• Status of outputs DO1 to DO8
Right row:
• Software status (slow flash = OK)
• Communication with Service Tool
• Communication on LON
• Communication with AK-CM 102
• Alarm when LED flashes
- 1 LED that is not used
• Communication with display on RJ11 plug
• “Service Pin” switch has been activated
A small module (option board) can be placed on the bottom part
of the controller. The module is described later in the document.
■Power
■Comm
■DO1 ■Status
■DO2 ■Service Tool
■DO3 ■LON
■DO4 ■I/O Extension
■DO5 ■Alarm
■DO6
■DO7 ■Display
■DO8 ■Service Pin
PIN
Address Keep the safety
distance!
Low and high
voltage must not
be connected to
the same output
group
Slow flash = OK
Quick flash = answer from gateway
Constantly ON = error
Constantly OFF = error
Flash = active alarm/not cancelled
Constant ON = Active alarm/cancelled

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 13
Point
Signal Signal
type
S
Pt 1000 ohm/0°C
Ss
Sd
Shr
Sgc
Sc3
Saux_
Pt 1000
P
AKS 32R
AKS 32
P0
Pc
Pgc
Prec
Paux
AKS 32R /
AKS 2050/
MBS 8250
-1 - xx bar
AKS 32
-1 - zz bar
U
...
0 - 5 V
0 - 10 V
On/Off Ext.
Main
switch
Day/
Night
Door
Level
switch
Active at:
Closed
/
Open
DO
AKV
Comp
Fan
Alarm
Solenoid
valve
Active at:
On
/
Off
Option Board Please see the signal
on the page with the
module.
Signal Module Point Terminal Signal type /
Active at
1
1(AI 1) 1 - 2
2(AI 2) 3 - 4
3(AI 3) 5 - 6
4(AI 4) 7 - 8
5(AI 5) 9 - 10
6(AI 6) 11 - 12
7(AI 7) 13 - 14
8(AI 8) 19 - 20
9(AI 9) 21 - 22
10 (AI 10) 23 - 24
11 (AI 11) 25 - 26
12 (DO 1) 31 - 32
13 (DO 2) 33 - 34
14 (DO 3) 35 - 36
15 (DO 4) 37 - 38
16 (DO 5) 39 - 40- 41
17 (DO6) 42 - 43 - 44
18 (DO7) 45 - 46 - 47
19 (DO8) 48 - 49 - 50
24 -
25 -
Terminal 15: 12 V
Terminal 16: 5 V
Terminal 27: 12 V
Terminal 28: 5 V
Terminal
17, 18, 29, 30:
(Cable screen)
Solid state outputs
on 12 - 15
Relay or AKV coil
fx 230 V a.c.
Relay outputs on
16 - 19
Analog
inputs
on 1 - 11
Point 1 2 3 4 5 6 7 8 9 10 11
Type AI1 AI2 AI3 AI4 AI5 AI6 AI7 AI8 AI9 AI10 AI11
Point 12 13 14 15 16 17 18 19
Type DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8
24 and 25 used
only when "Op-
tion board fitted"
3: Brown
2: Blue
1: Black
3: Brown
2: Black
1: Red
AKV

14 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
Extension module AK-XM 101A
Function
The module contains 8 analog inputs for sensors, pressure trans-
mitters, voltage signals and contact signals.
Supply voltage
The supply voltage to the module comes from the previous mod-
ule in the row.
Supply voltage to a pressure transmitter can be taken from either
the 5 V output or the 12 V output depending on transmitter type.
Light-emitting diodes
Only the two top LED’s are used. They indicate the following:
• Voltage supply to the module
• Communication with the controller is active (red = error)

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 15
Signal Module Point Terminal Signal type /
Active at
1(AI 1) 1 - 2
2(AI 2) 3 - 4
3(AI 3) 5 - 6
4(AI 4) 7 - 8
5(AI 5) 17 - 18
6(AI 6) 19 - 20
7(AI 7) 21 - 22
8(AI 8) 23 - 24
Point
Signal Signal
type
S
Pt 1000 ohm/0°C
Ss
Sd
Shr
Sgc
Sc3
Saux_
Pt 1000
P
AKS 32R
AKS 32
P0
Pc
Pgc
Prec
Paux
AKS 32R /
AKS 2050/
MBS 8250
-1 - xx bar
AKS 32
-1 - zz bar
U
... 0 - 5 V
0 - 10 V
On/Off Ext.
Main
switch
Day/
Night
Door
Level
switch
Active at:
Closed
/
Open
Point 5 6 7 8
Type AI5 AI6 AI7 AI8
Point 1 2 3 4
Type AI1 AI2 AI3 AI4
Terminal 9: 12 V
Terminal 10: 5 V
Terminal 15: 5 V
Terminal 16: 12 V
Terminal
11, 12, 13, 14:
(Cable screen)
At the top the
signal input is
the left of the
two terminals.
At the bottom
the signal input
is the right of the
two terminals.
3: Brown
2: Blue
1: Black
3: Brown
2: Black
1: Red

16 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
AK-XM 102B
Max. 230 V
On/Off:
On: DI > 80 V a.c.
Off: DI < 24 V a.c.
AK-XM 102A
Max. 24 V
On/Off:
On: DI > 10 V a.c.
Off: DI < 2 V a.c.
Extension module AK-XM 102A / AK-XM 102B
Function
The module contains 8 inputs for on/off voltage signals.
Signal
AK-XM 102A is for low voltage signals.
AK-XM 102B is for high voltage signals.
Supply voltage
The supply voltage to the module comes from the previous
module in the row.
Light-emitting diodes
They indicate:
• Voltage supply to the module
• Communication with the controller is active (red = error)
• Status of the individual inputs 1 to 8 (when lit = voltage)

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 17
Signal Module Point Terminal Active at
1(DI 1) 1 - 2
2(DI 2) 3 - 4
3(DI 3) 5 - 6
4(DI 4) 7 - 8
5(DI 5) 9 - 10
6(DI 6) 11 - 12
7(DI 7) 13 - 14
8(DI 8) 15 - 16
Point
Signal Active at
DI Ext.
Main
switch
Day/
Night
Comp.
safety 1
Comp.
safety 2
Level
switch
Closed
(voltage on)
/
Open
(voltage off)
Point 5 6 7 8
Type DI5 DI6 DI7 DI8
Point 1 2 3 4
Type DI1 DI2 DI3 DI4
AK-XM 102A: Max. 24 V
AK-XM 102B: Max. 230 V
(The module can not register a pulse signal from e.g. a
reset function.)

18 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
Extension module AK-XM 103A
Function
The module contains :
4 analog inputs for sensors, pressure transmitters, voltage signals
and contact signals.
4 analog voltage outputs of 0 - 10 V
Supply voltage
The supply voltage to the module comes from the previous
module in the row.
Supply voltage to a pressure transmitter can be taken from either
the 5 V output or the 12 V output depending on transmitter type.
Galvanic isolation
The inputs are galvanically separated from the outlets.
The outlets AO1 and AO2 are galvanically separated from AO3 and
AO4.
Light-emitting diodes
Only the two top LED’s are used. They indicate the following:
• Voltage supply to the module
• Communication with the controller is active (red = error)
Max. load
I < 2.5 mA
R > 4 kΩ

AK-PC 772A Capacity controller RS8HF102 © Danfoss 2017-07 19
Signal Module Point Terminal Signal type /Active at
1(AI 1) 1 - 2
2(AI 2) 3 - 4
3(AI 3) 5 - 6
4(AI 4) 7 - 8
5(AO 1) 17 - 18
6(AO 2) 19 - 20
7(AO 3) 21 - 22
8(AO 4) 23 - 24
Point
Signal Signal
type
S
Pt 1000 ohm/0°C
Ss
Sd
Shr
Sgc
Sc3
Saux_
Pt 1000
P
AKS 32R
AKS 32
P0
Pc
Pgc
Prec
Paux
AKS 32R /
AKS 2050 /
MBS 8250
-1 - xx bar
AKS 32
-1 - zz bar
U
... 0 - 5 V
0 - 10 V
On/Off Ext.
Main
switch
Day/
Night
Door
Level
switch
Active at:
Closed
/
Open
AO
0-10 V
Terminal 9: 12 V
Terminal 10: 5 V
Terminal
11, 12:
(Cable screen)
Galvanic isolation:
AI 1-4 ≠ AO 1-2 ≠ AO 3-4
Point 5 6 7 8
Type AO1 AO2 AO3 AO4
Point 1 2 3 4
Type AI1 AI2 AI3 AI4
3: Brown
2: Blue
1: Black
3: Brown
2: Black
1: Red
At the top the
signal input is
the left of the
two terminals.
At the bottom
the signal input
is the right of the
two terminals.

20 Capacity controller RS8HF102 © Danfoss 2017-07 AK-PC 772A
Extension module AK-XM 204A / AK-XM 204B
AK-XM 204A AK-XM 204B
Max. 230 V
AC-1: max. 4 A (ohmic)
AC-15: max. 3 A (Inductive)
Function
The module contains 8 relay outputs.
Supply voltage
The supply voltage to the module comes from the previous mod-
ule in the row.
AK-XM 204B only
Override of relay
Eight change-over switches at the front make it possible to over-
ride the relay’s function.
Either to position OFF or ON.
In position Auto the controller carries out the control.
Light-emitting diodes
There are two rows with LED’s. They mean:
Left row:
• Voltage supply to the controller
• Communication active with the bottom PC board (red = error)
• Status of outputs DO1 to DO8
Right row: (AK-XM 204B only):
• Override of relays
ON = override
OFF = no override
Fuses
Behind the upper part there is a fuse for each output.
Keep the safety distance!
Low and high voltage
must not be connected to
the same output group
AK-XM 204B
Override of relay