Danfoss AME 110 NL User manual

1
VD.KH.C6.02 © Danfoss 01/2014
SMT/SI
Actuators for modulating control
AME 110 NL, AME 120 NL
Data sheet
Description The actuators are used together with
automatically balanced combination valve type
AB-QM for DN 10-32.
The actuator can be used with fan coil units,
induction units, small reheaters, recoolers and
zone applications in which hot/cold water is the
controlled medium.
Main data:
• Gapdetectionatstemupposition
• Modulatingcontrol
• Forceswitch-oatstemdownposition
prevents overload of actuator and valve
• Notoolsrequiredformounting
• Maintenance-freelifetime
• Low-noiseoperation
• Self-positioningprocess
• Halogenfreecables
Ordering Type Supply voltage Speed Cable length Code No,
(V) (s/mm) (m) SinglePack IndustryPack
AME110NL
24 AC
24
1,5 082H8057 082H8067
5,0 082H8081 082H8077
10 082H8098 082H8087
AME120NL 12
1,5 082H8059 /
5,0 /082H8079
10 /082H8089
Note:
Actuators with 5 m and 10 m cable length are produced on request. Please note this increases lead time.
Spare parts
Type Length Code No.
(m)
Cable (24 V) 5082H8052
10 082H8054

2VD.KH.C6.02 © Danfoss 01/2014 SMT/SI
Data sheet Actuators for modulating control AME 110 NL, AME 120 NL
Technical data
Type AME 110 NL AME 120 NL
Powersupply V 24 AC; +20 to −15% *
Powerconsumption running VA 2
standby W0,5
Frequency Hz 50/60
Control input Y V0-10(2-10)Ri=110kΩ
mA 0-20(4-20)Ri=500Ω
Closing force N130
Stroke mm 5
Speed s/mm 24 12
Relative humidity max. 80 %
Max. medium temperature
°C
120
Ambient temperature 0 … 55
Storageandtransporttemperature –40 … 70
Protectionclass III safety extra-low voltage
Gradeofenclosure IP42
Weight kg 0,3
-markinginaccordancewith
standards
LowVoltageDirective2006/95/EC:EN60730-1,EN60730-2-14
EMCDirective2004/108/EEC:EN61000-6-2,EN61000-6-3
* 24V AC; +10% to −15% if produced before w18y2013
Installation Mechanical
The actuator should be mounted with the valve
stem in either horizontal position or pointing
upwards.
The actuator is fixed to the valve body by means
ofamountingring,whichrequiresnotoolsfor
mounting. The ring should be tightened by hand.
Electrical
Important: It is strongly recommended that the
mechanical installation is completed before the
electrical installation.
Auto sleep mode
1. IfactuatorAME110NLischargedby24V
supply voltage and if it is not installed on
AB-QM valve, it will stop in lower position and
switchoallLEDindicatorsafter5minutes
2. It is mandatory to drive the spindle of the
actuator to upper position before it will be
installed on AB-QM valve (please refer to
manual override drawings)!
3. Autosleepmodeswitchesbacktolearning
modebypressingRESETbuttonorbycycling
power supply
Each actuator is supplied with the connecting
cable for the controller.

3
VD.KH.C6.02 © Danfoss 01/2014
SMT/SI
position
indicator
Data sheet Actuators for modulating control AME 110 NL, AME 120 NL
1. Checkthevalveneck.Theactuatorshouldbe
in stem up position (factory setting).
Ensure that the actuator is mounted securely
on the valve body
2. Wire the actuator according to the
wiring diagram
3. The direction of the stem movement can be
observed on the position indicator
Installation procedure
Wiring
Commissioning The factory setting of the spindle is the fully
stem up position because of easier mechanical
connection of the actuator on the valve.
Disposal The actuator must be dismantled and the
elements sorted into various material groups
before disposal.

4
VD.KH.C6.02 © Danfoss 01/2014
SMT/SI
Reset

Data sheet Actuators for modulating control AME 110 NL, AME 120 NL
DIP Switch Setting
(for service purposes only)
TheactuatorhasafunctionselectionDIPswitch
under the removable cover.
Theswitchprovidesthefollowingfunctions:
• SW1:
U/I - Input signal type selector
 IfsettoOFFposition,voltageinputis
selected. If set to ON position, current input is
selected.
• SW2:
0/2 - Input signal range selector
 IfsettoOFFposition,theinputsignalisin
the range from 2-10 V (voltage input) or from
4-20 mA (current input). If set to ON position,
the input signal is in the range from 0-10
V (voltage input) or from 0-20 mA (current
input).
• SW3:
D/I - Direct or inverse acting selector
 IfsettoOFFposition,theactuatorisdirect
acting (stem contracts as voltage increases). If
the actuator is set to ON position, the actuator
is inverse acting (stem extracts as voltage
increases).
• SW4:
---/Seq - Normal or sequential mode
selector
 IfsettoOFFposition,theactuatorisworking
in the range 0(2)-10 V or 0(4)-20 mA. If set
toONposition,theactuatorisworkingin
sequentialrange;0(2)-5(6)Vor
(0(4-0(12) mA) or (5(6)-10 V) or
(10(12)-20 mA).
• SW5:
0-5/5-10 V - Input signal range in
sequential mode
 IfsettoOFFposition,theactuatorisworking
inthesequentialrange0(2) - 5(6) V or
0(4) - 10(12) mA. If set to ON position, the
actuatorisworkinginthesequentialrange;
5(6)-10 V or 10(12)-20 mA.
• SW6:
LIN/LOG - Linear or equal percentage flow
through valve selector
If set to ON position, the flow through the
valveisequalpercentage-wiseequalsthe
controlsignal.IfsettoOFFposition,thevalve
position is linear acc. to the control signal.
• SW7:
---/ASTK - Anti-blocking function
 Exercisesthevalvetoavoidblockingin
periodswhentheheating/coolingiso.
 IfsettoONposition(ASTK),thevalvemotion
is switched on. The actuator opens and closes
the valve every 7 days.
 IfsettoOFFposition(---),thefunctionis
disabled.
• SW8:
Reset switch and reset button on PCB
Changing this switch position will cause the
actuatortogothroughaselfstrokingcycle.
Note: Reset switch and reset button on
PCBhave the same function. The reset
switchmustbeinOFFpositiontomake reset
button function active ( press it for 2 sec. ).
Remark:
Factory setting: All switches (except switch 2 which is in ON position) are in OFF positions.

I 0-10 INV SEQ 5-10 LOG ASTX RESET
ON
OFF
U
2-10
DIR
---
0-5
LIN
---
RESET

5
VD.KH.C6.02 © Danfoss 01/2014
SMT/SI
⑤
①
②
③④
Data sheet Actuators for modulating control AME 110 NL, AME 120 NL
• Removecover①
• Pressandholdthebutton②(on the
bottom side of the actuator) during manual
override ③
• Replacecover④
• Installactuatoronvalve⑤
Remark:
A‘click’soundafterenergisingtheactuator
indicates that the gear wheel has jumped into
normal position.
If manual override has been used, the Y
signal will not be correct until the actuator
has reached its end position. If this is not
acceptable, reset the actuator.
Manual override
(for service purposes only)
Caution:
Do not manually operate the
drive if power is connected!
Do not dismount the actuator
from the valve when it is in a
stem down position!
If dismounted in a stem down
position,thereisahighrisk
thattheactuatorgetsstuck.
Dimensions (mm)

6VD.KH.C6.02 © Danfoss 01/2014 SMT/SI
Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

7
VD.KH.C6.02 © Danfoss 01/2014
SMT/SI
Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

8VD.KH.C6.02 Produced by Danfoss A/S © 01/2014
Data sheet Actuators for modulating control AME 110 NL, AME 120 NL