73690900/VI.HU.M2.02
2 | © Danfoss | DHS-SRMT/SI | 2018.11
oss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
vided that such alterations can be made without subsequential changes being necessary eady agreed.
All trademarks in this material are property of the respec
tive companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
NovoCon® S - High Accuracy Actuator
Part Name
部件名称
Hazardous Substances Table/有害物质含量表
Pb/铅Hg/汞Cd/镉Cr(VI)/
六价铬
PBB/
多溴联苯
PBDE/
多溴二苯醚
Union nut /
连接螺母 X O O O O O
O: Indicates that this hazardous substance contained in all of the homogeneous material for this part is below the limit requirement in GB/T 26572;
O: 表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572规定的限量要求以下。
X: Indicates that this hazardous substance contained in at least one of the homogeneous material for this part is above the limit requirementw in GB/T 26572;
X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。
NovoCon® S
Application mode:
MSV:9 / 32810
Digital control (default),
Analog
control, CO6 mode, Inverted
CO6 mode, CO6 without alarms,
Inverted CO6 without alarms
Select Valve Type
MSV:3 / 32802
(default AB-QM DN 15)
Design Flow Rate
AV:30 / 32796 Heating
AV:31 / 32798 Cooling
Select application
MSV:10 / 33811
Heating (default)
Cooling
❽
E100 VXX
281624
0030471
E100 VXX
281624
0030471
MADE IN SLOVENIA
NovoCon
S
003Z8504
Actuator for AB-QM DN10-32
Control signal: BACnet MS/TP, Modbus RTU, 0-10V, 0-20mA
®
6430 Nordborg, Denmark
Power: 24VAC/DC, 50/60 HZ
Force: 90N. Stroke: 7 mm. Speed: 3-24s/mm
Consumption: 3.3VA running. Standby 0.9W
IP54/40, -10T55
III
01
E100 VXX
281624
0030471
MADE IN SLOVENIA
NovoCon S
003Z8504
Actuator for AB-QM DN10-32
Control signal: BACnet MS/TP, Modbus RTU, 0-10V, 0-20mA
®
6430 Nordborg, Denmark
Power: 24VAC/DC, 50/60 HZ
Force: 90N. Stroke: 7 mm. Speed: 3-24s/mm
Consumption: 3.3VA running. Standby 0.9W
IP54/40, -10T55
III
01
01
Serial number and QR code can be removed from the
NovoCon® S label and added to installation drawing.
Device Object
Instance Number
❾ ❿
⓫
Presettings
DIP Switch
DIP Switches 1 to 7 are used to assign the MAC address manually. Default MAC address assignment
method is Auto MAC addressing for BACnet MS/TP and DIP Switches for Modbus RTU.
For termination of last unit on the field bus, turn DIP Switch 8 ON.
Dip switch 9 is not used.
Dip switch 10 is used to select between BACnet MS/TP (OFF=Default) and Modbus RTU (ON).
When the protocol is changed on DIP Switch 10, a power cycle is required.
12345678910
ON
OFF
To avoidinjuryanddamagetopersons anddevices, it is absolutely
necessary these instructions are carefully read and observed prior
to assembly and commissioning.
Necessary assembly, start-up, and maintenance work must be
performed only by qualified, trained and authorised personnel.
Switch off the power line before wiring the actuator.
Connect via safety isolating transformer.
Galvanic separations shall be provided for segments crossing buildings.
This product should be dismantled and its components sorted if
possible, in various groups before recycling or disposal.
Always follow the local disposal regulations.
Disposal instruction
Safety Note
Safety Note
⓬
If the NovoCon® S network is supplied with two or more AC power
boosters, caution must be observed when disconnecting one of the
transformers from the high voltage power line. As the NovoCons are
connectedinadaisychain,theremaybehighvoltageontheprimary
side of the disconnected power supply. Disconnect always both the primary
and secondary side of the transformer.
Safety Note
