Danfoss VLT AutomationDrive FC 360 User manual

The instructions provide information about the replacement of
the VLT
®
AutomationDrive FC 360 front cover.
Only Danfoss-authorised, qualified personnel is allowed to
repair this equipment. The personnel must be familiar with the
instructions and safety measures described in the
VLT
®
AutomationDrive FC 360 Service Manual.
1.1.1 Items Supplied
Items supplied depend on ordered code number and
enclosure type of the frequency converter.
Code number Items supplied
132B0296 Front cover, enclosure type J6
132B0314 Front cover, enclosure type J7
1.1.2 Tools Required
•
Screwdrivers:
-Flat-edged
-T10
-T20
-T25
-T30
•
N8 socket wrench
•
N10 socket wrench
•
N5 Allen key
1.1.3 Safety Instructions
WARNING
DISCHARGE TIME
The frequency converter contains DC-link capacitors, which
can remain charged even when the frequency converter is
not powered. Failure to wait the specified time after power
has been removed before performing service or repair work,
could result in death or serious injury.
1. Stop the motor.
2. Disconnect AC mains, permanent magnet type
motors, and remote DC-link power supplies,
including battery back-ups, UPS, and DC-link
connections to other frequency converters.
3. Wait for the capacitors to discharge fully, before
performing any service or repair work. The duration
of waiting time is specified in Table 1.1.
Voltage [V]
Minimum waiting time (minutes)
415
380-480 0.37-7.5 kW 11-75 kW
High voltage may be present even when the warning LEDs are off!
Table 1.1 Discharge Time
1.1.4 Installation
1. Remove the LCP (Local Control Panel) with a flat-
edged screwdriver (accessed from the top).
2. Push down the lock lever with a flat-edged
screwdriver and lift the plastic cover. Remove the
plastic cover beneath the LCP.
Installation Instructions
Front Cover
VLT®AutomationDrive FC 360
Danfoss A/S © Rev. 2014-01-17 All rights reserved. MI06R102

Illustration 1.1 Remove Plastic Cover
3. Remove 4 screws (T20, M4x8) that fasten the front
cover to the base plate.
Illustration 1.2 Location of Screws on Top Plate, Example
(Enclosure Type J6)
Illustration 1.3 Location of Screws on Bottom Plate, Example
(Enclosure Type J6)
4. Remove the 2 (for enclosure type J7) or 3 (for
enclosure type J6) screws on the I/O decoupling
plate.
Illustration 1.4 Screws on the I/O Decoupling Plate for Enclosure
Type J6
Installation Instructions Front Cover
VLT
®
AutomationDrive FC 360
2 Danfoss A/S © Rev. 2014-01-17 All rights reserved. MI06R102

Illustration 1.5 Screws on the I/O Decoupling Plate for Enclosure
Type J7
5. Remove the front cover, and install a new front cover
in reverse order.
Installation Instructions Front Cover
VLT
®
AutomationDrive FC 360
MI06R102 Danfoss A/S © Rev. 2014-01-17 All rights reserved. 3

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on
order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss
and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
www.danfoss.com/drives
*MI06R102*
MI06R102132R0218 Rev. 2014-01-17