Decon wheel E-Drive, Etac Prio User manual

10/6/2020
Assembly instructions for E-Drive, Etac Prio
MED3167
1. Remove wheels on both sides.
2. Check the correct placement for the stop pin according to the arrows above.
20”, 22”, 24” and 26”

10/6/2020
3. Mount the bracket as shown in the pictures above. Pictures shows the mounting on the
right-hand side. Start by removing the original Hub Sleeve and plastic insert.
Use the supplied mounting tool (12) to bring down the spacer (10) to the desired hole in
the wheelchair. Mount the Cover (11). Check in the Etac user manual how to position
the Hub Sleeve to get the desired seating height.
Parts for assembly on one side.
Item No. Part Number Qty Description
1 MED2000 1 Bracket
2 XSM16M 1 Nut M16X1 Low
3 XSM8ML 1 Nut Self-Locking M8
4 XSM8X45 1 Screw Round M8 x 45
5 HW069 1 Hub Sleeve M16x1/12,7
6 100 400 007 1 Spacer
7 100 400 017 1 Spacer
8 XSM16BR3 1 Washer 17x24x1
9 100 400 085 1 Spacer
10 100 400 087 1 Spacer
11 MED1636 1 Cover
12 MED1637 1*pair Mounting set Mounting Tool
4. Assemble the back placed battery bag.
NOTE! With E-Drive assembled to the wheelchair it is not possible to equip the wheelchair with Etac:s
cane holder 27327
12 11
8
2
3 6
9
4
5
1
7
10
If the Hub Sleeve is
mounted in these holes the
angel of the backrest is
limited to 15 degrees.
10
Tightening torque
20Nm
Tightening torque
30Nm. Use threadlock
Loctite 243 when
mounting.

10/6/2020
Assembly of Joystick with the Swing Away bracket
MED1484
Item No. Part Number Qty Description
1 MED1432R 1 Bracket right side
2 XOC-48160-C0 1 Upper holder assembly 2
3 XSM6ML 2 Nut Self-Locking M6
4 XSM6BR 2 Washer M6
5 XSM6X16 2 Screw Round M6 x 16
6 MC6SM5x16 2 Screw M5x16
NOTE!For mounting on the left side, use MED1432L instead of MED1432R.
6

10/6/2020
Assembly of Joystick with the Parallel bracket
MED1485
Item No. Part Number Qty Description
1 XSM6X16 2 Screw Round M6 x 16
2 MED1432R 1 Bracket right side
3 XSM6BR 2 Washer M6
4 XSM6ML 2 Nut Self-Locking M6
5 X0F-48160-D00 1 Parallel Bracket
6 MCSM5x16 2 Screw M5x16
NOTE!For mounting on the left side, use MED1432L instead of MED1432R.
6

10/6/2020
Assistant control Assembly
Assemble the assistant control on the right side
Item No. Part Number Qty Description
1 MED1200 1 Assistant controller
2 91312-06050 1 Screw Socket M6 x 50
3 92902-06200 2 Washer Plain M6
4 XA2-2612E-00 1 Clamp
5 XOD-2612K-00 1 Clamp2
1
3
4
5
3
2

10/6/2020
Om inget annat specifiseras, använd följande åtdragningsmoment.
Unless otherwise specified, use the following tightening torque.
Metriska grovgängor, stål.
Metric coarse threads, steel.
Gänga / Thread
Åtdragningsmoment / Tightening torque
M3
1,2 Nm
M4
3 Nm
M5
6 Nm
M6
10 Nm
M8
25 Nm
M10
50 Nm
M12
85 Nm
Navhylsor.
Hubsleever.
Gänga / Thread
Åtdragningsmoment / Tightening torque
M16x1
30 Nm
M18x1
40 Nm