Decorotika Esla User manual

assembly gude
Esla Nghtstand
1

e-mal : sales@decorotka.com
The US Phone : [phone] Workng Hours: Mon- Fr (09 am - 05 pm)
EUROPE Phone : [phone] Workng Hours: Mon- Fr (07 am - 05 pm)
ntroducton
Valued Customer,
We desgn and carefully manufacture our
products for our customers, We wsh that our
customers to have fun whle they are dong
ther new furnture
The product you just purchased was subjected
to all sorts of tests and controls before sendng
out to you.
Hope you enjoy your new furnture!!!
Before startng, please check all
components and accessores
accordng to the provded lst. If
you purchased more than one
product, to prevent confuson, be
sure that you completed the first
product, then start the next one.
Please make sure that you select
correct numbered part and use
specfic connector to assemble.
We do not recommend any
modficaton or rotaton n assembly.
Please follow the manual carefully.
Furnture parts are gong to several
manufacturng procedures. Durng ths
process, parts can have lttle dust or
marks. Please clean the parts wth
dump cloth before assembly to get
the best result. Usual cleanng would
be suffice.
Although all products are carefully
manufactured and packed, sometmes we
experence damage durng transportaton. In
such cases, please check the damaged part,
note the part number wrtten on the part and
do not hestate to contact us
Do not use your furnture for out of
purposes. If you would lke to use t
out of purpose or would lke to do
some modficaton or rotaton, please
contact us for more detals.
Please do not expose your furnture
wth excessve heat, cold and
humdty because product can be
affected negatvely.
2

or
o
before you start
Do not nstall the product on rough surfaces.
Get requred nstallaton tools prepared.
Get help from someone else!
3

*Please notce that there s an small arrow on
A02 (mnfix head).Ths arrow should show the
drecton of upper hole.
*After attachng two peces please turn the A02
(mnfix head) clockwse drecton wth the help
of a screwdrver.
gettng famlar wth the man components
MINIFIX
HEAD
MINIFIX
SCREW
DOWEL
*Please do not over screw the mnfix head snce t
may be broken f too much power s mposed.Just
make sure that t s screwed to the drecton “+” do not
go any further.
*Minifix is the main connecon component used in
Decoroka products.Before starng, please check
the below figures
4

naled shelf pn
5
01
02
03
Parça
3
03
03
Parça
04
03
Parça
05
03
Parça
06
ACCESSORY LIST
GENERAL VIEW
minifix head
A02
18 mm sticker
A06
c 1
A03
3.5x18 mm screw
BYZ
4x50 mm screw
A20
A04
A18
A18
C01
C04
A10A10
c 1
D01
A02A04A40
A18
XX4X
2X
2X
X4XXX
D01
Z39
X
4
4 4
424 12
A12
R2
4X
minifix screw
nail
furniture feet full overlay bracelet
14 mm sticker pivot

1step a
*Please attach the pece #1 onto the peces #4 and #5 as shown below
*Now screw the A17(4x50 mm screw) wth the help of a screwdrver clockwse drecton
step b
*Please nsert A03 (mnfix screw) nto the holes on the pece #3 as shown below
*Please nsert A02 (mnfix head) nto the holes on the peces #4 and #5 as shown below
*Make sure that all the arrows on A02 (mnfix head) are n correct drecton
*Please attach the pece #3 onto the peces #4 and #5 as shown below
*Now screw the A02 (mnfix head) clockwse drecton wth the help of screwdrver.
6
X
4x50
A17
4
2
03
Parça
04
03
Parça
05
01
03
Parça
3
03
X
A03
4
A02
x
4
03
Parça
04
03
Parça
05
01

03
Parça
05
03
Parça
04
3
step c
*Furnture feet consst of two parts; nner part and cover.
*Please take the nner parts of feet then put them on the mark holes
*Screw all A18 (3.5x18 mm screw) wth screwdrver clockwse
drecton
*Now place all covers on the nner parts
step d
*Please nal down R2(naled shelf pn )wth the help of an hammer on the peces #4 and #5
*Then please put the pece #2 onto the R2(naled shelf pn) as shown below
7
X
A18
3,5x18
16
01
A12
R2
4X
02
4

step e
*Please put C01 (bracelet) nto the bg holes on pece #6 the way they wll fit the pre-drlled holes
*Now take A18 (3.5x18 mm screw) and put them on pre-drlled holes
then turn them all wth screwdrver
*Please put all the C04 (pvot ) the way that they wll fit the pre-drlled holes on the pece #5
*Now take A18 (3.5x18 screw) and put them on pre-drlled holes then turn them all wth screwdrver
8
5
C01
d1
X
2
2
C04
X
03
Parça
06
03
Parça
05
X
A18
3,5x18
8

step f
*Please connect C04(pvot) and C01 (bracelet) as shown n figure
*Turn the screw A
*You can make some adjustment wth screw B for better openng and closng of door
6
1
2
A=
B = to arrange the door
to connect the hinge to the door arrows to show the directions for arrangement of doors.
03
Parça
06
03
Parça
05
9

D01
A02A04A40
nail
X
12
A06
step h
*For the best appearance of your furnture please place all A06(18 mm stcker)
onto the A02 (mnfix head)
*For the best appearance of your furnture please place all A10(14 mm stcker)
onto the A20(4x50 mm screw)
8
7step g
*Please take the panel and nal down wth the help of a hammer
*For the best result use all nals gven n the hardware pack
10

final look
Enjoy your Decorotka product!
contact@decorotka.com www.decorotka.us
www.decorotka.com
11