LAZBOY Sawyer Side Table User manual

Page 1 of 6
Sawyer Side Table
Owner’s Manual
La-Z-Boy® is a registered trademark of La-Z-Boy Incorporated and is used under license to
BJI,Inc. © 2019 La-Z-Boy Incorporated.
If you have any problems with this product, DO NOT RETURN IT TO THE STORE.
CALL OUR CUSTOMER SERVICE HOTLINE AT
877-592-7514
Monday – Friday, 8AM-5PM (EST)

Page 2 of 6
Care and Maintenance
Be careful to never allow water to build up in frames as this will cause corrosion and freeze damage in cold
climates. Wash all frames with a solution of mild soap and water. Rinse with clean water and dry with a soft
absorbent cloth towel. Frames can be treated with a liquid wax for maximum protection against UV rays and/or
salty damp air. If your set includes cushions, slings, and/or an umbrella they may be cleaned by hand with a
solution of soap and water with a clean water rinse. (Never machine wash cushions, slings or umbrella covers
as this will result in shrinkage or damage).
After cleaning cushions tip on end and allow to drip dry. (Never use a commercial or home dryer to tumble dry
fabric goods).
Do not use bleach or solvents to clean any product! This will void the warranty.
Lack of original receipt will void warranty!
CAUTION: Read all the instructions before assembly.Failure to do so may result in faulty assembly and
potential injury!
Assemble product on a soft, non-abrasive surface such as a carpet or cardboard to avoid damaging the item.
Seek assistance to assemble bulky or heavy items.After final alignment, make sure all bolts and nuts are
securely tightened with screw head covers pressed in place.
Note:Do not allow children to play with plastic wraps or small parts to prevent potential choking hazard.
For warranty and other helpful information, please visit www.lazboyoutdoor.com or call 1-877-592-7514,
Monday-Friday, 8AM-5PM (EST)or email us at [email protected].

Page 3 of 6
PARTS LIST
PART#
DESCRIPTION
PICTURE
Q’TY
A
Table Rim
1
B
Table Leg
4
C
Leg Stretcher
1
D
Glass Top
1
E
Hex Head Bolt M6x15 mm
12
F
Washer M6
12
G
Plastic Cap M6
12
H
Hex Wrench
1

Page 4 of 6
Assembly Steps:
Step 1. Carefully place the table rim (A) upside down on a non-abrasive surface. Then assemble
the table legs (B) to the table rim (A) with bolts (E) and washers (F) by using hex wrench (H).
See Figure 1.
Part# A x 1 Part# B x 4 Part# E x 8 Part# F x 8 Part# G x 8
Figure 1
Note:DO NOT tighten the bolts completely at this stage.
Step 2. Assemble the leg stretcher (C) to the table legs (B) with bolts (E) and washers (F) by
using hex wrench (H). See Figure 2.
Part# C x 1 Part# E x 4 Part# F x 4 Part# G x 4
Figure 2
Note: Tighten completely until all the bolts are in place.Then cover the bolts with plastic
caps (G) .

Page 5 of 6
Step 3. Turn your table right side down,then place the glass top (D) on the table rim (A).
See Figure 3
Part# D x 1
Figure 3
Now your table is ready for your enjoyment!

Page 6 of 6
Warning:
a..Do not crawl, stand, or sit on glass table tops.
b..Do not set or lay heavy items on glass table tops.
c..Avoid extreme hot & cold items being placed on glass table tops.
d..This glass table top is produced with tempered glass which is designed to
safely shatter in small pieces when impacted or stressed beyond strength
limitations.