Deep Sea Electronics Plc 8620 Setup guide

TYPICAL
WIRING DIAGRAM
A larger diagram is available in the operators manual.
Deep Sea Electronics Plc.
Tel:[phone]
Fax: [phone]
LO CALL (from UK BT landlines) :
Telephone [phone]
Email: [email protected]
Web:
www.deepseaplc.
com
Deep Sea Electronics inc.
Phone: [phone]-
8706
Fax: [phone]-
8708
TOLL FREE (USA only) : Tel: [phone]
Email: [e-mail]
Web: www.deepseausa.com
DIMENSIONS AND MOUNTING
For flat surface mounting in a Type 1 enclosure to meet UL requirements
DIMENSIONS
240.0mm x 181.1mm x 41.7mm (9.4” x 7.1” x 1.6”)
PANEL CUTOUT
:
220mm x 160mm (8.7” x 6.3”)
ACCESSING THE FRONT PANEL CONFIGURATION EDITOR.
•
Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset
•Press the Stop/Reset and Info
buttons simultaneously.
•
If a module security PIN has been set, the PIN number request is then
shown :
•Press the button the first digit will flash
to
•Press (up) or (down to
adjust
•Press (right)
when the first digit is c
show ‘#’ for security.
• Repeat this process for the other digits o
f the PIN number. You can press
back to adjust one of the previous digits.
• When
is pressed after editing the final
not correct, you must re-enter the PIN.
•
If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :
EDI
TING A PARAMETER
•Enter the editor as described above.
•Press the or
to cycle to the section you wish to view/change.
to cycle to the parameter
within the section you have chosen.
•To edit the parameter, press
to enter edit mode. The parameter begins to flash to indicate that
you are editing the value.
•Press the up or down buttons to
change the parameter to the required value.
•Press to save the value
. The parameter
•
To exit the editor at any time, press and hold the
DEE P SE A EL E CT R ONI CS
862
0 INSTALLATION INSTRUCT IONS
Deep Sea Electronics inc.
8706
8708
TOLL FREE (USA only) : Tel: [phone]
Email: [e-mail]
Web: www.deepseausa.com
NOTE: When the editor is visible, it is automatically exited after 5
NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5
NOTE: When the editor is visible, it is automatically exited after 5
ensure security.
ensure security.ensure security.
ensure security.
NOTE:
NOTE: NOTE:
NOTE:
The PIN number is automatically reset hen the editor is exited (manually or
The PIN number is automatically reset hen the editor is exited (manually or The PIN number is automatically reset hen the editor is exited (manually or
The PIN number is automatically reset hen the editor is exited (manually or
automatically) to ensure security.
automatically) to ensure security.automatically) to ensure security.
automatically) to ensure security.
NOTE:
NOTE: NOTE:
NOTE:
More comprehensive module configuration is possible using the
More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the
More comprehensive module configuration is possible using the
configurati
configuraticonfigurati
configuration soft are
on soft areon soft are
on soft are.
. .
.
Please contact us for further details
Please contact us for further detailsPlease contact us for further details
Please contact us for further details
NOTE: The contents of the tables overleaf may differ depending on the actual module
NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module
NOTE: The contents of the tables overleaf may differ depending on the actual module
configuration.
configuration. configuration.
configuration.
220mm x 160mm (8.7” x 6.3”)
ACCESSING THE FRONT PANEL CONFIGURATION EDITOR.
Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset
button.
buttons simultaneously.
If a module security PIN has been set, the PIN number request is then
to
enable the pin to be entered.
adjust
it to the correct value)
s correctly entered. The digit you have just entered will now
f the PIN number. You can press
(left) if you need to move
al PIN digit, the PIN is checked for validity. If the number is
If the PIN has been successfully entered (or the module PIN has not been
to cycle to the section you wish to view/change.
Then press or
within the section you have chosen.
to enter edit mode. The parameter begins to flash to indicate that
change the parameter to the required value.
. The parameter
ceases flashing to indicate that it has been saved.
To exit the editor at any time, press and hold the
or
button
.
DEE P SE A EL E CT R ONI CS
0 INST ALLATION INSTRU CTIONS
053-129
ISSUE 1
NOTE: When the editor is visible, it is automatically exited after 5
NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5
NOTE: When the editor is visible, it is automatically exited after 5
minutes of inactivity to
minutes of inactivity to minutes of inactivity to
minutes of inactivity to
The PIN number is automatically reset hen the editor is exited (manually or
The PIN number is automatically reset hen the editor is exited (manually or The PIN number is automatically reset hen the editor is exited (manually or
The PIN number is automatically reset hen the editor is exited (manually or
More comprehensive module configuration is possible using the
More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the
More comprehensive module configuration is possible using the
86
8686
86xx series PC
xx series PC xx series PC
xx series PC
Please contact us for further details
Please contact us for further detailsPlease contact us for further details
Please contact us for further details
NOTE: The contents of the tables overleaf may differ depending on the actual module
NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module
NOTE: The contents of the tables overleaf may differ depending on the actual module

ADJUSTABLE PARAMETERS
Front Panel Configuration Editor
Section Parameter as shown on display Values
Display
Contrast 53%
Language English, others.
Current Date and Time
hh:mm
Timers
LCD Page Timer 5m
Scroll Delay
2
s
Engine Pre Heat Timer 0s
Engine Crank Duration 10s
Engine Crank Rest Time 10s
Engine Safety On Delay 10s
Engine Smoke Limiting 0s
Engine Smoke Limiting Off 0s
Engine arm Up Time 0s
Engine Cool Down Time 1m
Engine Speed Overshoot Delay 0s
Engine Failed To Stop 30s
Battery Under Voltage arning Delay 1m
Battery Over Voltage arning Delay 1m
Return Delay 30s
Generator Transient Delay 0s
Mains Transient Delay 2s
Mains transfer time 0.7s
Mains
Mains Under Voltage Alarm 184V
Mains Over Voltage Alarm 277V
Mains Under Frequency Alarm 45Hz
Mains over Frequency Alarm 55Hz
Mains Transient Delay 2s
CT Primary
600A
CT Secondary
5A
Mains K Rating
345k
Mains KVar Rating
258k
Generator
Under Voltage Shutdown 184v
Under Voltage Pre-Alarm 196v
Nominal Voltage 230v
Over Voltage Pre-Alarm 265v
Over Voltage Shutdown 277v
Under Frequency Shutdown 40Hz
Under Frequency Pre-Alarm 42Hz
Nominal frequency 50Hz
Over Frequency Pre-Alarm 54Hz
Over Frequency Shutdown 57Hz
Full Load Rating 500A
k Overload Trip 100%
Delayed Over current Active
Delayed Over Current 100%
AC System 3 Phase 4 ire
CT Primary 600A Power Cycle After Exit
CT Secondary 5A Power Cycle After Exit
Short Circuit Trip 200%
Earth CT Primary 500A
Earth Fault Trip Active
Earth Fault Trip 10%
Transient Delay 0s
Gen Reverse Power Delay 2s
Full k rating 345k
Full kVAr rating 258kVAr
Load Ramp Rate 3%
Gen Reverse Power 35k
Insufficient Capacity Delay 1s
Insufficient Capacity action None
Reactive Load CTL mode VAr fixed export
Load Parallel Power 50%
Load Power Factor 1.00pf 0 KVAr 0%
Engine
Oil Pressure Low shutdown 1.03bar
Oil Pressure Low Pre-Alarm 1.24bar
Coolant Temp High Pre-Alarm 90ºC
Coolant Temp High Electrical Trip 92ºC ( hen Enabled)
Coolant Temp High Shutdown 95ºC
Start Delay Off load 5s
Start Delay on load 5s
Start Delay Telemetry 5s
Pre Heat Timer 0s
Crank Duration 10s
Crank rest Time 10s
Safety On Delay 10s
Smoke Limiting 0s
Smoke limiting off 0s
arm Up Time 0s
Cool Down Time 1m
Speed Overshoot Delay 0s
Speed Overshoot 0%
Fail To Stop Delay 30s
Battery Under Volts arning Active
Battery Under Volts arning Delay 1m
Continued Overleaf
Front Panel
Configuration Editor (continued)
Section Parameter as shown on display Values
Engine (Continued)
Battery Under Volts arning 10v
Battery Over Volts arning Active
Battery Over Volts arning Delay 1m
Battery Over Volts arning 30v
Charge Alternator Failure arning Active
Charge Alternator Failure arning 6.0v
Charge Alternator arning Delay
5s
Charge Alternator Failure Shutdown
Ina
ctive
Charge Alternator Failure Shutdown 4.0v (When Enabled)
Charge Alternator Shutdown Delay 5s (When Enabled)
Droop % Active, Inactive. Electronic engines only when
droop is enabled.
Scheduler
Scheduler Active, Inactive
Schedule On Load Active , Inactive (Only Available When
Scheduler Is Active)
Schedule Period Weekly, Monthly (Only AvailableWhen
Scheduler Is Active)
Schedule Time & Date Selection (1-16)
Press to begin editing then or
when selecting the different
parameters in the scheduler.
ACCESSING THE ‘RUNNING’ CONFIGURATION EDITOR
•The ‘running’ editor can be entered while the engine is running. All protections remain active if the
engine is running while the running editor is entered.
•Press and hold the button to enter the running editor.
ADJUSTABLE PARAMETERS (Running editor)
•Enter the editor as described above.
•Press the up or down buttons to cycle to the section you wish to view/change.
•To Edit the parameter press the button to enter edit mode. The parameter begins to flash to
indicate that you are editing the value.
•Press the up or down buttons to change the parameter to the required value.
•Press the button to save the value. The parameter ceases flashing to indicate that it has been
saved.
•To exit the editor at any time , press and hold the button.
Running Editor
Section Parameter as shown on display Factory Settings
DISPLAY
Contrast
53%
Language English
Load Power factor
0
-
100%
(0)
Load parallel power 0-100%
(50)
)
Commissioning screens
Inactive
,
Active
Override starting alarms Inactive, Active
Voltage adjust (manual mode only engine running breaker open) 0-100 % (0)
Frequency adjust (manual mode only engine running breaker open) 0-100 % (0)
Auxiliary Mains Fail Out of sync reset Inactive Active
Mains decoupling test mode (Stop mode only) Inactive Active