Degelman CASE IH MX 215 User manual

MANUAL
143253
Tractors
CASE IH MX 215- 305
®

272 Industrial Drive, Box 830
Regina, Sask. Canada S4P 3B1
306 543-4447 543-2140 fx
[email protected]
www.degelman.com
Blade, pivot frame 1
Cylinders & Hydraulics 3
Main Frame, Brackets, Mounting 5
Safety, Operation, Maintenance 9
Attachments 11
Warranty 12
SAFETY
143253
Tractors
The safety instructions that follow
pertain only to this specific
equipment. You should be aware
of agricultural & industrial safety
especially related to heavy
equipment. If you are not familiar
with safety procedures then you
should get training.
Improper use will result in maiming
or death.
CASE IH MX 215 - 305
®

p1
143253
®
CASE IH MX 215-305
Blade Components
24
12
25
10
23
22
11
15
14
14
13
13
2
26
26
1
7
4
5
15
96
8
17
16
18
19
20
3

p2
143253
Pivot Frame
21 781220 Pivot frame 1
22 781336 Angle cyl pin 4
23 118011 Bolt 1/2 x 1 1/2 4
24 118504 Lock washer 1/2 4
25 118587 Flat washer 1/2 4
26 117145 Wear bushing 1 1/2 6
1 781302 14ft 59 Dlock 1
781301 12ft 1
781300 10ft 1
2 781328 Bell 1
3 781326 Tilt ring 2
4 118051 Bolt 3/4 x 3 Gr. 8 6
5 117414 Locknut 3/4, Gr.C unitorq. 6
6 781370 Relief valve bracket 1
7 781340 Pivot pin, blade-pivot 1
8 118795 Bolt 5/8 x 2 1/4 2
9 118447 Locknut 5/8, Gr.C unitorq. 2
10 806014 Depth shoe 2
11 115402 Pin 4 1/8 2
12 118901 Lynch pin 2
13 116207 7ft Cutting edge 2
116206 6ft 2
116210 10ft 1
14 118204 Plow bolt 5/8 x 2 1/4 a/r
15 118447 Locknut 5/8, Gr.C unitorq. a/r
16 141524 Relief valve 1
17 118105 Bolt 5/16 x 2 1/2 2
18 118538 Flat washer 5/16 2
19 118530 Lock washer 5/16 2
20 118427 Nut 5/16 2
Qty
21 24
25
22
26
23

143253
®
CASE IH MX 215-305
Cylinders
p3
Tilt Cylinders
1 122552 Barrrel 1
2 122563 Piston 1
3 122558 Lock ring 1
4 122556 Open Cap 1
5 122560 Rod & Clevis 1
6 118441 Lock nut 7/8 UNF unitorq. 1
7 122670 Pin 1-1/2 x 2-3/4 2
8 118796 Shoulder Bolt 1/2 gr8 UNC 2
9 118924 Flat washer .59 ID x .9 OD 2
10 122523 Seal kit 1
122550, 3 x 8 x 1-1/2 Tilt cylinder Qty per cyl
Lift Cylinders
1 122652 Barrrel 1
2 122663 Piston 1
3 122658 Lock ring 1
4 122656 Open Cap 1
5 122660 Rod & Clevis 1
6 118441 Lock nut 7/8 UNF unitorq. 1
7 122670 Pin 1-1/2 x 2-3/4 2
8 118796 Shoulder Bolt 1/2 gr8 UNC 2
9 118924 Flat washer .59 ID x .9 OD 2
10 122522 Seal kit 1
122650, 3-1/2 x 8 x 1-1/2 Lift cylinder
781380 Lift Hydraulic Kit
Qty per cyl
781400 Tilt Hydraulic Kit
Angle Cylinders
Qty per cyl
1 122602 Barrrel 1
2 122210 Piston 1
3 122558 Lock ring 1
4 122209 Open Cap 1
5 122206 Rod & Ball Joint 1
6 118441 Lock nut 7/8 UNF unitorq. 1
7 122212 Seal kit 1
122200, 3 x 20 x 2 Angle cylinder
781390 Angle Hydraulic Kit
Angle Cylinders (alternate)
Qty per cyl
1 122602 Barrrel 1
2 122563 Piston 1
3 122558 Lock ring 1
4 122556 Open Cap 1
5 122606 Rod & Ball Joint 1
6 118441 Lock nut 7/8 UNF unitorq. 1
7 122523 Seal kit 1
122600, 3 x 20 x 1-1/2 Angle cylinder
781390 Angle Hydraulic Kit
1
2345
6
7
8
9
7
89
10
10
1
234
5
6
7
8
9
7
89
1
1
2
2
3
3
4
4
5
5
6
6
7
7

143253
Hydraulics
p4
Qty
126578 Hose 3/8 x 9 2
126605 Hose 3/8 x 18 2
126579 Hose 3/8 x 204 2
126548 Hose 3/8 x 50 4
126553 Hose 3/8 x 216 4
126585 Hose 3/8 x 25 2
126538 Hose 3/8 x 66 6
Hose lengths ( ) in inches
1 141504 EL 3/4 m JIC x ORB 16
2 141501 TEE 3/4 m JIC 2
3 141515 Nipple 3/4 m JIC x ORB 2
4 141527 TEE 3/4 m JIC x JIC x ORB 4
5 141517 Connector 3/4 JIC m 6
6 141581 Quick coupler 6
QtyHydraulic Fittings
Use different coloured tape to
mark sets of hydraulic hoses.
Use one or two tapes to
indicate lifting or retracting
hoses.
133091 Coloured hose markers, 1 pack
1
456
23
TiltTilt
(25)(25)
(216)
(216)
(204) (204)
(216) (216)
(216)
continued
(216)
continued
Relief
Angle
Angle
(50) (50)
(50)
(50)
(9)
(18)
(9)
(18)
Lift Lift
Hose take-up
(204)
continued
(204)
continued
(66)(66)
TILT CYLINDERS
LIFT CYLINDERS
ANGLE CYLINDERS
11
4
4
4
4
11
11 3
3
11
2
2
11
5
5
5 5
5
5
1
66
6
6
6
6
1
1 1
1
1

18
18 19
p5
143253
®
CASE IH MX 215-305
1 - Main Frame
2 - Front Hanger
3
4
5
5
6 - Front Bracket
78
9
10
11
12
13 8
8
14 - Side Bracket
7
16 - Rear Frame
17
15
17
20
22 23
21
Tractor's weight stack;
remove when dozing
Cut threaded rod
to length
Tractor's weight stack;
remove when dozing
Cut
threaded rod
to length
9
10
12
13 11
Negative Boosting
Post Bushing

Hook hose take up
to tractor frame
Tractor's hyd
ports at rear
p6
143253
Brackets & Components
1 780360 Main frame 1
2 780465 Front hanger 1
3 118048 Bolt 3/4 x 2 1/2 16
4 118422 Lock nut 3/4 16
5 118775 Flat washer 3/4 32
6 780470 Front bracket 1
7 118198 Bolt M20 x 70 10
8 118551 Lock washer M20 10
9 780666 Spacer pipe 1
10 780667 Threaded rod 1
11 118407 Nut 5/8 2
12 118508 Lock washer 5/8 2
13 118514 Flat washer 5/8 2
14 780671 RH side bracket 1
780672 LH 1
15 118753 Bolt M20 x 140 1
7 Bolt M20 x 70 13 23
8 Lock washer M20 14 24
16 780210 Rear frame 1
17 118743 Bolt 3/4 x 2 1/4 20
18 118509 Lock washer 3/4 20
19 118410 Nut 3/4 20
20 780356 Pivot pin, main-pivot 1
21 118645 Bolt 5/8 x 1 1/4 1
22 118508 Lock washer 5/8 1
23 118514 Flat washer 5/8 1
24 780270 Hose take up 1
25 780274 Spring 1
Qty
Qty for that
application & grand
total for this
assembly 25
24
Main frame: 5th, 7th, 9th, 11th, 13th
Rear frame
1st 2nd 3rd 4th 5th
Front bolt bar
Front bracket
& hanger
Mid Mount
Side Bracket
Main & rear frame
bolt hole alignment

p7
143253
®
CASE IH MX 215-305
1 780145 Dlock linkage 2
2 118030 Bolt 5/8 x 3 2
3 780788 DL bushing 2
4 118448 Lock nut 5/8 2
5 780789 UHMW plastic block 2
6 243500 Lock pin 2
DL linkage includes..
7 780143 Wedge 1
8 143116 Compression spring 1
9 118913 Roll pin 1
10 780146 DL linkage plate/bush 1
11 780150 DL handle 1
6 Lock pin 1 3
12 780273 Hose clamp 4 part 3
includes...
13 118144 Bolt 5/16 x 1 1/2 1
14 780279 Top plate 1
15 780278 Clamp two halves 1
16 780277 Bottom plate weld on 1
Qty
Qty for that
application & grand
total for this assembly
7
9
8
10
1
2
3
4
12
13
14
15
16
11 5
6
6
5

Take clip
pin off
Make sure Dlock
is closed properly
To disengage:
1- RAISE THE BLADE
2- Open the Dlock
3- Extend lift cylinder to lower rear frame
4- Lower main frame to graund
5- Back out to clear front hanger
6- Unhook hydraulics
WARNING
It is vital to raise the blade before opening Dlock.
If you don't the rear frame will fall.
Dlock closing
Use the
handle to
close the
latch
Note the second
position for the final
movement of closing
Secure with
clip pin
Put
handle
away
143253
Mounting
Line tractor up over the rear/main frames. Make sure Dlock is open, clip pin is
put back on and handle is stored.
Drive forward so that the front bracket pin is just behind the front hanger's hook. It should be
lined up so you can drive into the front hanger when it is raised up. Hook up the hydraulics.
Raise the front hanger by extending the lift cylinders so the pin and hook are level.
Now close the lift cylinders. This will raise up the rear frame. Take off clip, close
the Dlock, attach clip then store the handle.
Drive forward until the pin is in the front hanger.
There should
be a 3/8" gap

all hardware
TORQUE
Why is SAFETY important to YOU?
3 BIG Reasons:
• Accidents Can Disable and Kill
• Accidents Are Costly
• Accidents Can Be Avoided
p9
143253
®
CASE IH MX 215-305
YOU ARE RESPONSIBLE
. . . for your own safety and that of others. If you are
not familiar with basic agriculture & industrial safety,
you must get training. Owners of equipment must by
law give operating instructions to other operators
such as family members or a hired hand.
Making any design changes to equipment could
cause a hazard and damage your machine.
Wear proper safety equipment.
Have handy:
• First aid kit
• Fire extinguisher
Before working on machine:
• Turn tractor off
• Set controls in neutral
• Remove ignition key
Keep all parts clean. Replace worn or damaged parts.
Don’t try any makeshift repairs. Before operating
check that everything is tight and not broken.
Wear gloves and eye protection when searching
for leaks. Use a piece of wood or cardboard but
not your hand. High pressure oil will penetrate
your skin. If that happens you risk serious injury.
Lower blade to the ground when not in use. Keep clear of
blade when tractor is running. Keep hands & feet away from
under blade. Turn engine off when hooking up hydraulics
and engaging DLOCK during mounting or dismounting.
Lift blade up then hold with safety chain.
Make sure SMV sign & reflectors are clean.
Use your hazard lights.
HYDRAULIC
BLADE
TRANSPORTING
Operation & Maintenance
• Lube all points
• Torque all hardware to correct setting
• Check hardware torque & hydraulics after
the first 2 hrs & again after 10 hrs.
Before using for the first time
Check:
• If all points lubricated
• All components attached securely
• Condition of cutting edge
• Depth shoe wear
• Tractor’s Hydraulic oil reservoir
• Condition of hoses, lines & fittings
Before using each time Cycle the cylinders several times to warm up system.
Cold weather
Check torque on all hardware
periodically. Check after first 2,
10, 40, then every 200 hours.
IMPORTANT
Bleed hydraulics of air. Cycle the hydraulics
several times and hold the cylinders at full
extent for several seconds.
Bleeding hyd
If needed, balance out your tractor by
ballasting the rear end. You may need to
raise the tire pressure in the front wheels.
Consult your tractor's manual.
Rear end weights & Tire inflation
Here are some the things you can do
with your hyd system in float position;
• Skim the top of pavement
• Run on the skid shoes
• Back drag
Floatation mode

Torque Settings
Lube both sides
Tilt cyl
Front brkt
Bell, 4 places
Lift cyl
Tilt cyl
Angle cyl Angle cyl
Lift cyl
Tilt ring
Pivot pin, pivot/main frm
Dlock
Pivot pin, blade/pivot
Front brkt
Lube with:
Grease
Spray lubricant
Lube all points and mechanisms
after every 8 hr of use.
p10
143253
1/4 9 12
5/16 18 25
3/8 30 45
7/16 50 70
1/2 75 110
9/16 10 155
5/8 155 215
3/4 270 385
7/8 435 620
1 660 930
Imperial Gr. 5
(ft lb)
Gr. 8
3/4 75
7/8 90
(ft lb)
Hyd. Fittings
3 0.4 1.3
4 2.2 3.3
5 4 7
6 7 11
8 18 26
10 37 52
12 66 92
15 66 228
20 321 450
24 553 774
Metric 8.8
(ft lb)
- SAE
10.9
Operation & Maintenance
Depth shoes
Soft uneven ground
• Depth shoe low
• Blade high
Hard even ground
• Depth shoe high
• Blade low
?
NOTE: All hardware is Hex head, Plated,
Gr.5 UNC (imperial) or P10.9 2.5 (metric)
and all Hoses are 3/8, ends c/w 3/4 JIC
female swivel, unless stated otherwise.
NOTE: Some of the components in
this image may differ from your
current model. However, the areas
of lubrication remain the same.

p11
143253
®
CASE IH MX 215-305
11
Attachments
1 118043 Bolt 3/4 x 2 a/r
2 118516 Flat washer 3/4 a/r
3 118509 Lock washer 3/4 a/r
4 118410 Nut 3/4 a/r
5 118539 Flat washer 3/4 a/r
5
1
34
123
1
3
4
4
134
1
3
4
Silage extension
781570 14ft
781560 12ft
781550 10ft
1ft Extension
781586 -
Two
req'd
Side plate
781540
- Two Req'd
Top extension
781602 14ft
781601 12ft
781600 10ft
Replacement Decals/Reflectors
Attachment Hardware
142386 Warning decal, Falling Blade 2
142008 Degelman logo 25 3/4 lg 2
142280 Red reflector 6 3/8 2
142279 Amber reflector 3 1/4 lg 1
142780 5900 blade decal 1
5
5

Printed in Canada
Write down the following information about your dozer blade to better help you obtain assistance or service if you ever need it.
You will need to know your model number and serial number. You can find this information on the model and serial number
plate located on your dozer blade.
Degelman Industries Ltd. ("Degelman") warrants to the original purchaser of any new Degelman equipment, purchased from
an authorized Degelman dealer, that the equipment will be free from defects in material and workmanship for a period of two
(2) years from the date of delivery, for non-commercial use (including farm, institutional, government, and municipality) and (1)
year from the date of delivery for commercial use. The obligation of Degelman to the purchaser under this warranty is limited
to the repair or replacement of defective parts in the first year and to the provision, but not the installation of replacement parts
in the second year. Degelman reserves the right to inspect any equipment or parts which are claimed to have been defective in
material or workmanship.
This warranty limits its replacement or repair coverage to what is consistent with the warranty of Degelman's suppliers of
purchased components.
Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days
from the date of delivery of such part or the expiration of the applicable new equipment warranty period, which ever occurs
later. Warranted parts shall be provided at no cost to the user at an authorized Degelman dealer during regular working
hours. Warranted replacement parts will either be replaced or rebuilt at Degelman's discretion.
Disclaimer of implied warranties & consequential damages
This warranty shall not be interpreted to render Degelman Industries Ltd. liable for injury, death, property damage or damages
of any kind, whether direct, consequential, or contingent to property. Without limiting the generality of the foregoing,
Degelman shall not be liable for damages resulting from any cause beyond its reasonable control, including, without limitation,
loss of crops, any expense or loss of labour, supplies, rental machinery or loss of use.
No other warranty of any kind whatsoever, express or implied is made with respect to this sale; and all implied warranties of
merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby
disclaimed and excluded from this sale. This exclusion shall not apply in any jurisdiction where it is not permitted by law.
This limited warranty shall not apply:
1. If, in the sole opinion of Degelman, the unit has been subjected to misapplication, abuse, misuse, negligence accident or
incorrect installation.
2. To any goods that have sustained damage or deterioration attributable to a lack of routine maintenance (eg. Re-torque of
mounting hardware.)
3. If parts not made or supplied by Degelman have been used in the connection with the unit, if, in the sole judgement of
Degelman such use affects its performance, safety, stability or reliability.
4. If the unit has been altered or repaired outside of an authorized Degelman dealership in a manner which, in the sole
judgement of Degelman, affects its performance, safety, stability or reliability.
5. To expendable or wear items such as cutting edges, skid shoes, and any other items that in the company's sole judgement is
a wear item.
No employee or representative of Degelman Industries Ltd. is authorized to change this limited warranty in any way or grant
any other warranty unless such change is made in writing and signed by the Degelman Service Manager.
This limited warranty is subject to any future availability of supply, which may directly affect Degelman's ability to obtain
materials or manufacture replacement parts.
Degelman reserves the right to make improvements in design or changes in specifications at any time, without incurring
obligations to owners of equipment previously delivered.
This limited warranty is subject to compliance by the customer to the enclosed Retail Customer's Responsibility Under Degelman
Warranty.
Dealer Name
Address
Phone Number
Model Number
Serial Number
Purchase Date
p12
143253
0207
WARRANTY
2 Year
Limited Warranty