Delf Architectural Deadbolt User manual

ŸFold the supplied template and
position template on door edge.
ŸMark centre of 54mm hole on both
sides of door.
ŸMark horizontal centre-line of
25mm hole using template, then
mark centre of door thickness.
ŸDrill 54mm hole through door face,
from both sides to avoid
splintering.
ŸDrill 25mm hole into the edge of
the door, central to the door
thickness. Ensure the hole is drilled
squarely.
54mm
Step 1. Door Preparation
DOOR TEMPLATE
60mm BACKSET
Fold on dotted line &
position on door edge
Mark 25mm hole at
centre of door edge.
DB01DOC02- V2 JAN2018
I NSTALLATION INSTRUCTIONS
Deadbolt with Square Furniture
Step 3. Single Cylinder Only
This step only applies to single cylinder product. Skip to
STEP 4 if installing double cylinder product.
For single cylinder product, the
turn-button shaft must be on the
interior side of the door. If required,
re-orientate cylinder as below:
ŸRemove the hex screw at the
rear of the lockbody with allen
key provided.
ŸFlip the cylinder so the shaft is
on the interior side of the door
and slide cylinder back into
lockbody.
ŸRe-install the hex screw into the
lockbody and tighten.
DOOR
THICKNESS
32 - 39mm
39 - 48mm
Step 6. Screw Selection
ŸMeasure door thickness and select correct
mounting screws as per table below:
M4 x 40mm LONG
M4 x 50mm LONG
MOUNTING SCREW
Step 5. Lock-Bolt Installation
ŸRotate key towards edge of
door.
ŸOrientate lock-bolt as shown
and insert into bolt-housing.
ŸPush lock-bolt in until a click
is heard and the lock-bolt
wont go in any further.
ŸRotate key away from door
edge, if lock-bolt does not
retract then repeat above.
ŸPosition faceplate and pilot
drill holes for faceplate
screws, then install two
faceplate screws (#6 x 19mm).
UP
Turn-Button
Shaft
Single
Cylinder
Hex
Screw
Faceplate
screw
Lock-Bolt
Faceplate
ŸRemove both bolt-housing
screws from lockbody.
ŸRemove bolt housing and
lock-bolt from lockbody.
ŸPosition bolt-housing and
faceplate centrally within
25mm hole in door edge
and mark around the
rectangular portion of
faceplate.
ŸChisel marked rectangle to
a depth of 3.5mm or until
bolt-housing with faceplate
is flush with door edge.
ŸRemove bolt-housing and
faceplate from door before
moving to next step.
Step 2. Chisel Faceplate Recess
Lockbody
Bolt-
Housing
Lock-Bolt
Bolt-housing
Screw
Faceplate
Bolt-
Housing
Step 4. Lockbody Installation
ŸInstall lockbody into
door, with orientation as
shown.
ŸInstall bolt-housing into
25mm hole in door and
locate in lockbody.
ŸInstall 2 x bolt-housing
screws, one from each
side.
Bolt-housing
Screw
Lockbody
SUITS 32mm TO 48mm THICK DOORS

54mm DOOR TEMPLATE
60mm BACKSET
Fold on dotted line &
position on door edge
Mark 25mm hole at
centre of door edge.
DELF ARCHITECTURAL
T 1300 362 625 F 1300 362 643
E [e-mail]
W www.delfarchitectural.com.au
Step 7. Escutcheon Installation
INTERIOR
SIDE
OF DOOR
Step 8. Interior Escutcheon Installation
ŸPosition interior escutcheon over mounting
plate.
ŸWhile holding interior escutcheon squarely
on door face, tighten hex screw on underside
of escutcheon to secure onto door.
This step only applies to single cylinder product.
Skip to STEP 10 if installing double cylinder
product.
For single cylinder product:
ŸInstall turn-button onto shaft on interior side of
door. Orientate hex hole with flat on shaft.
ŸTighten hex screw with allen key provided.
Step 9. Single Cylinder only Step 10. Strike Plate Installation
Strike Plate
Screw
Strike Plate
Door Jamb
ŸExtend the lock-bolt.
ŸGently close the door until the lock-bolt rests on the door
jamb.
ŸMark centre of lock-bolt on door jamb, this mark can be used
to position strike plate.
ŸMark and drill 25mm hole inside the jamb to a depth of 25mm
on marked bolt centre position.
ŸPosition the strike plate and mark around. Chisel recess until
strike plate sits flush with door jamb face.
ŸFasten strike plate to door jamb with two strike plate screws
(#8 x 25mm)
Shaft
Turn-Button
Flat on Shaft
INSERT SCREWS
THROUGH HOLES
WITH ARROWS
Exterior
Escutcheon
Mounting
Plate
Mounting
Screws
Mounting
Plate
Hex
Screw
Interior
Escutcheon
ŸPosition exterior escutcheon on exterior side of door.
ŸPosition mounting plate on interior side of door.
ŸHold exterior escutcheon squarely on door then insert
correct mounting screws selected in STEP 6 through the
holes with arrows in mount plate and tighten.
ŸEnsure screws are not overtightened.
ŸCheck lock function, if lock-bolt is not retracting and
extending then repeat from STEP 5.