Assa Abloy ENTR User manual

ii ENTR™ User Manual
Table of Content
1. 5
1.1 Package Content 5
1.2 Tools Required 5
1.3 6
1.4 6
1.5 7
1.6 7
2. 9
2.1 9
2.2 9
2.3 ON/OFF Switch 10
2.3.1 Turning ENTR™ ON 10
2.3.2 Turning ENTR™ OFF 10
2.3.3 10
2.4 11
2.5 Default PIN Code 11
3. 12
3.1 Changing PIN Code 12
3.2 13
3.3 Pairing Remote Control 16
3.4 17
3.5 18
3.6 19
3.7 20
3.8 20

iii
ENTR™ User Manual
4. Touchpad Reader 21
4.1 Changing PIN Code 21
4.2 21
4.2.1 21
5. 22
5.1 22
5.2 Pairing Touchpad Reader 22
5.3 Touchpad Reader Master PIN Code 24
5.4 Menu Mode 24
5.5 Adding PIN Code 24
5.6 Open Door 25
5.7 Lock Door 25
5.8 Delete PIN Code 25
5.9 Delete all PIN Codes 25
5.10 Volume Control 26
5.11 Factory Reset 26
6. Fingerprint Reader 27
6.1 27
6.2 27
6.3 27
6.4 Pairing Fingerprint Reader 28
6.4.1 Add Master 29
6.4.2 Set Finger 29
6.4.3 Set PIN Code 29
6.5 Unlock Door 30

4ENTR™ User Manual iv
6.6 Lock Door 31
6.7 31
6.8 31
6.9 Add User 32
6.10 Delete User 33
6.11 Enable/Disable User 33
6.12 Delete all Users 34
6.13 Add Time Schedule 34
6.14 Edit Time Schedule 35
6.15 Volume Control 35
6.16 Double Security 36
6.17 Factory Reset 36
7. Smartphone App 37
7.1 37
7.2 Pairing Smartphone 38
8. 39
8.1 39
8.2 40
9. Sabbath Mode 41
10. ENTR™ Wire-free Charger 42
10.1 General 42
10.2 42
10.3 Door Unit Charging 42
11. 43
9.1 43
9.2 Cases 43
Limited Warranty 46

5
ENTR™ User Manual
1.1 Package Content
1.2 Tools Requirements
• 2mm Allen key
• 3mm Allen key
1.
Baseplate & knob1
Electrical unit2
Cylinder screw3
Panel screw4
charger5
Magnet6
Cylinder7
M5 screw8

6ENTR™ User Manual
• Press & hold the knob (1) and turn slightly (2) the cylinder cam is no longer
protruding from the side of the cylinder body (see
• Insert the cylinder (including baseplate & knob) from the interior side of the door.
• Once the cylinder is correctly aligned within the door, secure the cylinder in place
using the M5 screw.
• Do not over the screw or use power tools to do so.
Note: Do not hammer (or use any other excessive force) on the cylinder or knob when
them into the door.
• Turn the knob back to the zero Knob marks point upwards.
Note: The knob will jump out when returned to zero
Zero
Warning: Do not to operate the unit assembled on the door.

7
ENTR™ User Manual
• the magnet on the front panel of the door frame, as close as possible to
the lock.
• The top point of the magnet should be approximately 20mm below the M5 screw
(see
• Use the supplied double-sided to adhere magnet.
Note: The magnet area on door frame should be clean and free from dust, peeling
paint etc. If required use alcohol to clean. Wait completely dry prior to
• Insert the key into the external side of the cylinder and turn one full turn.
• Take the key out.
Note: Verify that the gear is not pressed in.
Gear not pressed in
Note: Follow the only if the cylinder was dismantled from the door unit.
Magnet
Door frame
Cylinder screw (M5)
20

8ENTR™ User Manual
• Assemble the cylinder into the door unit (baseplate & knob).
• Tighten the cylinder's screw.
• Connect the data cable plug.
• Assemble electrical unit as illustrated.
• Tighten the electrical unit's panel screw.
Note: Verify that the cylinder and the knob are
engaged. Press the knob and turn. If the knob can not
be pressed or turned, disassemble the cylinder, adjust
the cylinder's rectangle and reassemble.
• Verify that the rectangle driver (cylinder) aligned with the knob's rectangle bore.
If required, turn the rectangle driver (cylinder) it is in the same (see
below).
Knob back view
• Verify the knob is in zero Knob marks point upwards (see page 6).
screw
Driver
Data cable
1
2
Knob back view

9
ENTR™ User Manual
Error (Red)Door not closed (Red)
OK (Green)Manual mode (Green)Mute (Green)
Knob
Touchpad
ON/OFF switch
2.

10 ENTR™ User Manual
• Turning the ENTR™ lock ON or OFF.
2.3.1 Turning ENTR™ ON
Before turning ENTR™ ON,verify that the door is shut.
• Move the switch to the ON Make sure that
the knob is in the zero (see
• and numeric will blink all once.
• Hazard beep sound will be and error
will blink once.
• ENTR™ is now in mode.
Note:
• turning ENTR™ ON, avoid touching the front
panel beep sound ends.
• turning ENTR™ ON, the door will be shut but
not locked.
2.3.2 Turning ENTR™ OFF
• Move the switch to the OFF
red signal rapidly blinking and 2 long beeps will
be during every lock/unlock
that the is low and needs to be charged.
2.3 ON/OFF Switch
OFFON
ON
•
Zero