SDC 1511S Instruction Manual

1511S Operational Description (NFPA-101)
The 1511S operation complies with the following building and fire codes: NFPA 101; NFPA 1-UFC; UBC; IBC; IFC; SBC;
California Building Code. Listings: UL Listed: Special Locking Arrangements and Auxiliary Locks; California State Fire
Marshal (CSFM) Listed.
The door is normally closed & secured and/or latched. The model 1511S Exit Check secures the door in the locked
condition, and the display shows the preset delay time.
Activation of the 1511S Exit Check is made by releasing the door latch and applying up to 15 lbs. of pressure to the door,
giving a pre-activation warning tone. (A 1 or 2 second nuisance delay will prevent false activation of the alarm).
When the nuisance delay time has been exceeded, the Exit Check begins the irreversible door release cycle. At this
time the display continues to count down, the verbal warning continues and an alarm output is provided to alert
personnel of an unauthorized exit.
The integral digital countdown display and voice commands inform the person intending to exit of the seconds remaining
to unlock. The Exit Check will release the door after the 15 or 30 second delay cycle has expired, allowing free egress. A
steady warning tone with the voice command “Exit Now” will sound until the Exit Check is reset by authorized personnel.
1511S Operational Description (BOCA/Chicago)
The 1511S operation complies with BOCA National Building Code and the Chicago Building Code: UL Listed, Special
Locking Arrangements and Auxiliary Locks.
The releasing operation of the 1511S is the same as described above, with the exception that the door relocks
automatically 30 seconds after closure (reset switch not required). Each time the door is open before 30 seconds has
elapsed the relock timer resets and relocks the door in 30 seconds.
SECURITY DOOR CONTROLS
3580 Willow Lane, Westlake Village, CA 91361-4921 • [phone] • Fax: [phone]
www.sdcsecurity.com • E-mail: [e-mail]
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 1
INSTALLATION INSTRUCTIONS
EXIT CHECK
®
DELAYED EGRESS EMLOCK
®
1511S / 1511T
PUSH UNTIL ALARM
SOUNDS. DOOR CAN BE
OPENED IN 15 SECONDS.
Application
When unauthorized egress is initiated, the Exit Check
®
delays egress through the door for 15 or 30 seconds.
Meanwhile, the person exiting must wait while personnel or security respond. An integral digital countdown display and
voice commands inform the person intending to exit of the seconds remaining to unlock. The door unlocks after 15 or
30 seconds have elapsed, permitting egress. A signal from the fire/life safety system will release the lock for uninhibited
egress in an emergency.
Exit Check
®
applications include:
Restricting the egress of patients for their own safety.
Restricting the egress of commercial center patrons for security application needs.
Controlling pedestrian traffic in transportation facilities, including airport jetways and tarmacs
California Building
Code Compliant
KEEP PUSHING. THIS DOOR
WILL OPEN IN 15 SECONDS.
ALARM WILL SOUND.

Included in Package
1511S EMLOCK
HOUSING ASSY. &
MOUNTING PLATE
1511S TRIGGER &
ARMATURE BASE
1511S-11
1511S ARMATURE
1511S-12T
ARMATURE
SCREW PACK
1580S-101-C
EMLOCK
SCREW PACK
C-1500
TEMPLATE
TEMP-1511
728
Single station two
function key switch
control for alarm
reset and access or
sustained bypass.
928 Digital Keypad
Two relay outputs:
Relay 1 -Reset;
Relay 2 – Choice of
momentary or
sustained bypass.
101-4AM
Provides visual &
audible annunciation
with audible mute for
one, two, three or
four openings.
728-L
Single station two
function key switch
control for alarm reset
and access with a tri-
colored LED showing
door condition.
702-6R
Single station one
function key switch
control for alarm
reset.
101-1A
The single station
annunciator is
equipped with a tri-
colored LED and
audible alarm.
101-1AK
Visual & audible
annunciation and a
two function key
switch for alarm
reset and access or
sustained bypass.
101-PAM
Visual & audible
annunciation, timed
access, sustained
bypass and audible
mute.
SDC Annunciator Consoles
provide remote annunciation
of multiple openings. Stations
are specified in sets of four.
Control switches are capable
of both sustained bypass and
timed unlocking.
TCC Desk Top :
Stations 4, 8, & 12
Suggested Optional Equipment
Digital Entry
Power Supply
Station Controls, Annunciator Panels, and Consoles
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 2
600 Series Power Supply
Field Selectable 12 or 24VDC modular
Power Supplies with Fire/Life Safety
Emergency Release. Tri-colored LED,
separate PTC protected outputs, battery
charger, and Class 2 Outputs.
602RF 1 Amp
631RF 1.5 Amp
632RF 2 Amp
634RF 4 Amp
636RF 6 Amp
PSB560
Request-to-exit pressure
sense non-latching bar
that will activate the Exit
Check® when slight
pressure is applied to
the bar. For doors
without latching.
Remote Speaker
101-SP
Indoor Surface Mount;
85dB@3ft.;
Compact Design (4 in. sq.);
Plug-in connector included
for easy installation

Door and Frame Reference Dimensions
Door and Frame Preparation Instructions
HINGE SIDE OF FRAME
(OPPOSITE FROM LOCK)
PAPER TEMPLATE
STEP 1. Locate the paper template and fold
along the dotted line. Place the folded edge of
the template against the door stop and door at
the header while against the vertical stop,
opposite the hinge side of the door. Tape in
place at this position.
STEP 2. As indicated on the paper template,
punch the designated hole locations on the
frame and armature mounting holes on the door.
(NOTE: PRIOR TO DRILLING, INSPECT TO SEE IF
ANY OF THE HOLES CANNOT BE DRILLED DUE
TO THE FRAME OR DOOR CONFIGURATION. A
FILLER PLATE OR ANGLE BRACKET MAY BE
REQUIRED. SEE PAGE 4.)
STEP 3. Drill and tap the two 1511S mounting
holes as indicated on the paper template.
(NOTE: READ NOTE ON TEMPLATE WITH
REGARD TO SELECTING THE PROPER HOLE
SIZE FOR ARMATURE MOUNTING BOLT.)
2-1/2"
2-5/8"
11"
2-3/4”
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 3
NOTES:
-#10 self drill/tap screws provided for up to 1/8" thick metal applications
-For applications with heavier gauge material, drill (#21) and tap for #10-32 machine screws.
IMPORTANT! – IT IS HIGHLY RECOMMENDED THAT YOU FIRST INSTALL THE MOUNTING PLATE AT TWO SLOT LOCATIONS ONLY.
THIS WILL ALLOW YOU TO MAKE PROPER ADJUSTMENTS OF THE LOCK’S POSITION PRIOR TO MARKING, DRILLING AND TAPPING
THE FOUR PERMANENT MOUNTING PLATE HOLES.
PLACE AGAINST DOOR
PLACE AGAINST
DOOR JAMB
FOR R.H. DOOR
PLACE AGAINST
DOOR JAMB
FOR L.H. DOOR
DRILL 1/4” DIAMETER HOLE x 9/16" DEEP
CENTER PUNCH ON
MARK & REFER TO
INSTRUCTION SHEET
FOR HOLE SIZE.
PLACE AGAINST HEADER
1/2” DIA. HOLE Mark location four places.
FOLD ON DOTTED LINE
05/04
TEMP-1511
2"
13/16"
9/16"
1-1/16"
1-1/4”
4-5/8”
2-1/2”2-1/2”
1-1/8”
1-3/16” 1-1/2”
SLOT LOCATIONS
1-11/16” 4"

STEP 1. Mount armature to door. (See figures
2A, 2B & 2C.)
STEP 2. Install the mounting plate (filler plate
and/or angle bracket if needed – see figures 1A,
1B & 1C) to header with only the two screws at
the slotted hole locations at this time. Snug the
screws down lightly (do not torque) so the
mounting plate & lock can be repositioned later.
STEP 3. Temporarily install the lock to the
mounting plate with the 1/4-20 socket head
screws encased in the lock.
STEP 4. With the lock mounted, close the door
so the armature holder just comes into contact
with the face of the lock. If the door is not
completely closed when the lock & armature
touch, open the door and reposition the lock
away from the door as described in step 2.
(THIS IS TO PREVENT THE DOOR FROM USING
THE LOCK AS THE DOOR STOP.)
STEP 5. Remove the lock from the mounting
plate, mark & punch all remaining screw and
wiring holes. Drill & tap holes as indicated on the
paper template and install all screws.
STEP 6. Reinstall the lock to the mounting
plate. At this point, if there is no need to remove
the lock for painting or any other reason, install
the anti-tamper plugs over the socket head
mounting screws, using a soft hammer to avoid
damage to the lock case.
ARMATURE MOUNTING INSTRUCTIONS
Figure 2B – HOLLOW METAL DOOR
From sexnut side of door, drill exactly 1/2" hole through one metal thickness
only. From armature side of door, drill 5/8" hole to insert reinforcement tube.
Press in sexnut & reinforcement tube all the way and mount armature to door
using hardware provided per Figure 2B.
Figure 2A – SOLID DOOR
Drill exactly 3/8" diameter through the door. From sexnut side of
door, drill ½” diameter hole 1-3/8" deep. Mount armature to door with
hardware provided per Figure 2A.
Figure 2C – REINFORCED ALUMINUM OR
HOLLOW METAL DOOR
Use letter “F” drill and tap for 5/16-18 machine screw. Mount
armature to door with hardware provided per Figure 2C.
ARMATURE HOLDER
ARMATURE
5/16 – 18 ARMATURE
MOUNTING SCREW
DOOR
REINFORCEMENT
BY OTHERS
LETTER “F”
DRILL & TAP 5/16-18
REGULAR, FILLER PLATE & ANGLE BRACKET DETAILS
Figure 1A
REGULAR
Figure 1B
WITH FILLER PLATE
FILLER PLATE
Figure 1C
WITH ANGLE BRACKET
ANGLE BRACKET
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 4
ARMATURE HOLDER
5/16 – 18 ARMATURE
MOUNTING SCREW
ARMATURE
1/2”
SEX NUT
DOOR
1–3/8"
5/8" DRILL
5/16 – 18 ARMATURE
MOUNTING SCREW
ARMATURE HOLDER
ARMATURE
1/2" DRILL
REINFORCEMENT TUBE
1 – ¾” HOLLOW
METAL DOOR

P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 5
Typical System Wiring –
Single Door (Model 1511S)
600 Series
Power Supply
+
-
+
-
928
Digital Keypad
+
-
C
NO
(OPTIONAL)
728U or 728UL3
Key Switch
Reset Station
(OPTIONAL)
RED
GRN
BLK
WHT
BLK
BLU
BLK
3 or 5
conductors
8 or 10
conductors
Power
Supply
To Fire Panel
AC Mains
2 conductors
PUSH UN TIL ALARM
SOUNDS . DOOR CAN BE
OPENED IN 15 SECOND S.
Key Switch or
Access Control
(Optional)
L3
OPTION
REMOVE J6 ONLY IF A FIRE PANEL
OR SMOKE DETECTION SYSTEM IS
CONNECTED TO [FP] INPUT (Pg. 7)
To Smoke
Detection System
2 conductors
C NC
- + - + NC NONO C C NC NO CNO C NO C NO C NO C NC NO C NC
[ BAS ]
[ DPS ]
[RESET][RM TRIG] [REX]
[RED RLY][GRN RLY]
[ LOCK ]
[ FP ]
[ PWR ]
}
NOT
USED
J1
101-SP
Remote
Speaker
(OPTIONAL)
CONNECT PLUG TO
J1
J6
J7

P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 6
3 or 5
conductors
8 or 10
conductors
Power
Supply
To Fire Panel
AC Mains
2 conductors
4 conductors (1511T only)
PUSH UNTIL ALARM
SOUNDS. DOOR CAN BE
OPENED IN 15 SECONDS.
PUSH UNTIL ALARM
SOUNDS. DOOR CAN BE
OPENED IN 15 SECONDS.
+
-
600 Series
Power Supply
728U or 728UL3
Key Switch
Reset Station
(OPTIONAL)
RED
GRN
BLK
WHT
BLU
BLK
BLK
L3
OPTION
928
Digital Keypad
(OPTIONAL)
+
-
C
NO
Key Switch or
Access Control
(Optional)
Typical System Wiring –
Pair of Doors (Model 1511T)
REMOVE J6 ONLY IF A FIRE PANEL
OR SMOKE DETECTION SYSTEM IS
CONNECTED TO [FP] INPUT (Pg. 7)
SLAVE
To Smoke
Detection System
2 conductors
TB2 TB1
[ LOCK ]
IN [ PWR ]
TB5
TB6 TB4 TB3
[ DPS ]
[ BAS ]
TB7
NO C NC NO C NC NO C NC NO C
+ - + -
Z4
D1
Z1
D2
R7
RLY1
J1
R9
C4
BAS
DPS
C1
J4
TB8
[ ATS ]
[TRIG
OUT ]
C NC
- + - + NC NONO C C NC NO CNO C NO C NO C NO C NC NO C NC
[ BAS ][ DPS ]
[RESET][RM TRIG] [REX]
[RED RLY][GRN RLY]
[ LOCK ]
[ FP ]
[ PWR ]
}
NOT
USED
J1
MASTER
J6
J7

Wiring Details & Functions (ALL OPTIONS SHOWN)
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 7
REQUEST TO EXIT
KEY SWITCH OR
ACCESS
CONTROL
SYSTEM
(OPTIONAL) REMOTE RESET
SWITCH
(OPTIONAL)
REMOTE
STATUS PANEL
(OPTIONAL)
FIRE
ALARM
INPUT
(OPTIONAL)
POWER
SUPPLY
12VDC
OR 24VDC
Dry,
N/C
BLK
RMB X L3
RED
EXTERNAL
TRIGGER
SWITCH
OR
SDC REX PUSH BAR
(OPTIONAL)
TERMINAL BOARD CONNECTIONS
POWER IN -
POWER IN +
COM
N/C
AUX LOCK -
AUX LOCK +
N/O
COM
N/C
N/O
COM
N/C
N/O
COM
N/O
COM
N/O
COM
DOOR POSITION
SWITCH
(DPS)
BOND ALERT (BAS)
[PWR]
[FP]
[LOCK]
[GRN
RLY]
[RED
RLY]
[RM
TRIG]
[RESET]
[REX]
[DPS]
[BAS]
12 VDC OR 24 VDC
TO CLOSED FIRE/SMOKE
DETECTOR CONTACT
SLAVE/TANDEM LOCK
POWER TERMINALS
LOCK SECURE
OUTPUT
ALARM OUTPUT
EXTERNAL TRIGGER
SWITCH INPUT
EXTERNAL RESET
SWITCH INPUT
REQUEST TO EXIT
INPUT
N/O
COM
N/C
[ATS] ANTI-TAMPER SWITCH
(ATS)
MONITORING OPTIONS
N/O
COM
N/C
N/O
COM
N/C
GRN
SMOKE DETECTION
SYSTEM INPUT
(OPTIONAL)
Dry,
N/C
C NC- + - + NCNONO C C NC NO C
NO C NO CNO C NO C NC NO C NC
[ BAS ][ DPS ]
[RESET]TRIG] [REX]
[RED RLY][GRN RLY][LOCK]
[FP]
[PWR]
[RM
JUMPER
J6
(SEE PG 8)
FEATURE DIP SWITCH
(SEE PG. 8 FOR SETTINGS)
JUMPER J7
(SEE PG 8)
}
NOT
USED
NO C NC
[ ATS ]
J1
CONNECT PLUG TO
J1
REMOTE
SPEAKER
(OPTIONAL)
J6
J7

DIP SWITCH SETTINGS
REQUEST TO EXIT PERIOD – The Request to Exit (REX) time is selectable for 1, 15, 20, or 30 seconds. The REX time is the
period of time the lock will remain “bypassed”, after a remote normally open contact switch is momentarily activated. When activated
with an access control system, the REX time cycle begins immediately after the access control open time expires. The ExitCheck™
will automatically relock if the door is opened, and then closed during the REX time cycle.
TRIGGER TYPE – The trigger type is selectable for “REMOTE” or “INTERNAL”. Selecting INTERNAL mode uses the internal trigger
sensor to activate the Exit Delay cycle. Selecting REMOTE mode disables the internal trigger. Activation of the Exit Delay cycle is
triggered by an external exit device equipped with a normally open contact switch.
POWER-UP OPTION * – The power-up option, indicating the state of the ExitCheck
TM
upon restoration of system power, is selectable
to “UNLOCKED” or “LOCKED”. In the LOCKED mode, the ExitCheck
TM
will attempt to reset to secure mode. In the UNLOCKED
mode, the ExitCheck
TM
will remain unlocked and the digital display will indicate two horizontal bars “--“. Turning the reset switch
momentarily to the reset position will relock and rearm the door. This feature enables the ExitCheck
TM
to comply with code
requirements in jurisdictions that require manual reset/relock upon loss and restoration of system power.
ALARM TYPE – The alarm type is selectable to “TONE ONLY” or “VOICE”. When secure, the ExitCheck
TM
digital display will
indicate a 15 second delay time. Upon activation of the irreversible Exit Delay cycle, the digital display begins counting down to zero.
In VOICE mode, the countdown will be accompanied by a warning beeping tone and verbal exit instructions. When the digital display
indicates zero, the ExitCheck
TM
releases. The speaker output changes to a continuous warning tone and the verbal instruction
announces “Exit Now”. In TONE ONLY mode, the countdown will be accompanied by a warning beeping tone only, which changes to
a continuous tone once the Exit Delay cycle expires.
MESSAGE TYPE – The message type is selectable to “MSG1” or “MSG2”.
MSG1: (Female Voice) “Exit in 12 seconds, facility staff has been notified...Exit in 5 seconds...exit now...”
MSG2: (Male Voice) “Exit in 12 seconds, security has been alerted...Exit in 5 seconds...exit now…”
Both messages repeat “Exit now” until the lock is reset.
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 8
WARNING!
CONTACT AUTHORITY HAVING JURISDICTION FOR APPROVAL
PRIOR TO SELECTING DELAY TIME OR PWR-UP SETTINGS
*
OFF
MESSAGE TYPE
VOICE / TONE
PWR-UP OPTION *
REQUEST TO EXIT
RELOCK DELAY
(SEC)
NUISANCE
DELAY *
20 1530
1
LOCKED UNLOCKED
VOICE TONE
ONLY
MSG #2MSG #1
21 76 543 8
ON
TRIGGER TYPEREMOTE INTERNAL
ON
NUISANCE DELAY * – The Nuisance delay time feature, intended to avoid accidental triggering, is selectable for 1 or 2 seconds.
Releasing the door latch and pushing on the door will activate the internal trigger sensor. Activating the trigger beyond the nuisance
delay time will start the irreversible Exit Delay cycle time. The Nuisance Delay time period is included in the lock release cycle and it
will not increase or decrease the “total time to unlock” once the ExitCheck
TM
is activated. Releasing the door before the end of the
Nuisance delay time will turn off the warning alarm and reset the ExitCheck
TM
to secure mode.
RELEASE TIME * – The Release time is selectable for 15 or 30
seconds. The Nuisance Delay time period is included in the
door release cycle and it will not increase or decrease the “total
time to unlock” once the ExitCheck
TM
is activated.
1 SEC. 2 SEC.
RELEASE
TIME *
15 SEC. 30 SEC.
JUMPER SETTINGS
JUMPER J6 (Fire Alarm Input) – Factory Installed. Remove
J6 only if a dry, normally closed contact from a fire alarm OR
smoke detector system is connected to the Fire Panel [FP]
terminals.
JUMPER J7 (Door Prop) – When removed, the ExitCheck™
will allow the user to prop the door open indefinitely after a
valid REX input, without causing an alarm. The lock will
automatically relock once the door is closed.
With J7 installed, the ExitCheck™ will go into its alarm mode if
the door remains open after to the REX time expires.
J7
C NC- + - + NCNO
NO C C NC NO CNO C NO C NO C NO C NC NO C NC
[ BAS ][ DPS ]
[RESET]
TRIG] [REX]
[RED RLY][GRN RLY][LOCK]
[FP]
[PWR]
[RM
NO C NC
[ ATS ]
J1
J6
J7
J6

STEP 1. After the lock has been mounted to the door and frame per the provided template, feed the wiring
through the access hole and out to the controller board. Re-install the lock front cover onto the lock. Ensure that
the trigger sensor is aligned with the hole in the cover. The sensor is preset at the factory to slightly project through
the cover. WARNING: DO NOT ATTEMPT TO ADJUST THE TRIGGER SENSOR LENGTH. AS THIS WILL RESULT IN
DAMAGE TO THE SENSOR AND VOID THE WARRANTY.
STEP 2. Make all wiring connections to the lock. Observe the polarity of the input power terminals. The lock
senses the power supply voltage and automatically configures itself for 12vdc or 24vdc operation. Correct power
supply voltage must be used for proper lock operation. WARNING: INPUT TERMINALS FOR RESET, REX AND
REMOTE TRIGGER MUST ONLY BE CONNECTED TO A NORMALLY OPEN MOMENTARY DRY CONTACT SWITCH (I.E.
928 DIGITAL KEYPAD OR 728 KEY SWITCH). CONNECTION TO A VOLTAGE OR A “WET” OUTPUT MAY DAMAGE THE
LOCK AND VOID THE WARRANTY.
STEP 3. Slowly swing the door closed and visually observe the position of the armature trigger as it approaches
the trigger sensor on the lock. If the provided mounting template was used during the lock and armature installation,
the trigger & sensor should align with one another both horizontally and vertically. The LED on the back of the
trigger sensor will light when the armature trigger is detected. IMPORTANT: CORRECT OPERATION OF THIS LOCK
DEPENDS ON THE TRIGGER SENSOR BEING ABLE TO DETECT THE ARMATURE TRIGGER WHEN THE DOOR IS
CLOSED. A PROXIMITY ADJUSTMENT CAN BE MADE TO THE TRIGGER FOR FINE TUNING. THIS IS EXPLAINED IN
STEP 4.
STEP 4. After alignment has been verified, close the door and apply power to the lock. The digital display will
show a two bars “- -“ indicating that the lock is in the Manual Power Up mode. Push on the door to verify that the
door is unlocked. Reset the lock at this time by turning the built in key switch clockwise or by triggering the remote
reset input. The lock should now secure the door and the LED display will show the delay time . You may change
the mode to Auto Power Up by setting the #6 dipswitch to the ON position. Now when you first apply power, the
door will be secure and the LED display will display the delay time without having to reset the lock.
STEP 5. Activation of the 1511S can be made by door movement or an external trigger. When using the door
movement method, activation is achieved through the way the armature hardware is designed. When someone
unlatches the door and applies up to 15 lbs. pressure, the lock will hold onto the armature while simultaneously
letting the door & trigger armature move away from the lock & trigger sensor. Sensitivity in the detection of the
trigger movement can be adjusted for optimum sensitivity & performance. This adjustment can be made by using
the 5mm hex wrench provided with the lock. The center of the trigger or “target” is spring loaded and can be
screwed in and out of the armature thus either decreasing or increasing the space between itself and the sensor.
The “spring” feature of the target is to prevent damage from direct contact with the trigger sensor. Depending on the
accuracy of the alignment, the trigger does not have to physically touch the sensor to operate correctly.
TRIGGER SENSOR
TRIGGER
HORIZONTAL
ALIGNMENT
VERTICAL
ALIGNMENT
C
C
1511S LOCK BODY
1511S ARMATURE
1581S ARMATURE
Lock Adjustment and Operation
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 9

Standard Features
1650 lbs. Holding Force
15 or 30 Second Exit Delay when activated.
1 or 2 Second Nuisance Delay
75dB Alarm Tone with Digital Display & Selectable Voice
Instruction
Choice of Activation Trigger:
-Door Movement
-Exit Device w/ REX Switch
-Touch Sense Bar w/REX Switch
Vandal resistant Proximity Sensor Trigger
Auto Sensing 12/24VDC input power
Connection for Tandem Option (Pairs of Doors)
Optional Features
DPS Door Position Switch
BAS Bond Alert Sensor
ATS Anti Tamper Switch
EEnergy Saver Option (1200 lb. Holding Force)
Selectable Automatic & Manual Power-Up
Feature
Auto Power-Up – Occurs when power is restored and/or
the fire panel is restored.
Manual Power-Up – This is a UBC & California Building
Code Compliant Feature – Only after power restoration
and fire panel reset may the lock be reset manually at the
opening. Lock can be reset with the built-in reset key
switch or, a key switch or keypad adjacent to the door.
Inputs & Outputs
REX Input
Fire Alarm/Smoke Detection System Release
Remote Reset Input
Remote Trigger Input
Tandem/Slave Lock Input
DPS – Door Position Status (Optional)
BAS – Magnetic Bond Status (Optional)
ATS – Anti-Tamper (Optional)
Alarm Output
Lock Status Relay Output
-Door Secure
-Door Unlocked
Specifications
Interior Applications Only
Input Voltage Requirements:
Dual Voltage (Auto Sensing) –
12/24 VDC (+/- 10%)
Power Consumption:
Standard Model (1650 lbs.) -
1511S – 830/450 mA@ 12/24 VDC
1511T – 1500/850 mA @ 12/24 VDC
Energy Saver (1200 lbs., “E” Option) –
1511S – 400/275 mA@ 12/24 VDC
1511T – 650/400 mA @ 12/24 VDC
Size: 11"L x 2-3/4"H x 2-5/8"D
Lock Status Relay Rating: 1 Amp @ 30V resistive
Alarm Output Rating: 1 Amp @ 30V resistive
DPS Rating: 250 mA @ 30V resistive
BAS Rating: 250 mA @ 30V resistive
ATS Rating: 1 Amp @ 30V resistive
Building & Fire Life Safety Code Compliant
1511SND
IBC International Building Code
IFC International Fire Code
NFPA 101 Life Safety Code
NFPA 1, UFC, Uniform Fire Code
UBC Uniform Building Code
CBC California Building Code
SBC Standard Building Code
1511SBD
BOCA National Building Code compliant
1511SCD
Chicago Building Code compliant
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 10
GWXT Auxiliary Locks
FWAX Special Locking Arrangements
California State
Fire Marshal Listed
CSFM #3774-0324:103
LISTED
CANADA
LISTED
USA

Sense Bar Trigger Non-Latching
PSB560, MSB550
Power
PT-2
PT-3
Wall Mount Reset Station (Optional)
728
928
728L
702RU
101-1AK
Power
Latch Monitoring Strike Trigger
For Mortise Exit Devices
MS-16
Latch Trigger
Power
Remote Annuciators
and Control Panels
(Optional)
TCC / RCC
101-1A
101-4AM
101-PAM
Power
A pair of doors requires the 1511T
Power
Pushing either door triggers
the delayed release of both doors.
Latching Exit Device with
Built-in Switch Kit Trigger
Power
PT-2
PT-3
PTH-4
Hinge
Switch
Kit
PUSH UNTIL ALARM
SOUN DS. DO OR C AN BE
OPENED IN 15 SECONDS.
PUSH UNTIL ALARM
SOUN DS. DO OR C AN BE
OPENED IN 1 5 SECO NDS.
PUSH UNTIL ALARM
SOUNDS. DOOR CAN BE
OPENE D IN 1 5 SEC ONDS .
PUSH U NTI L A LARM
SOUNDS. DOOR CAN BE
OPENED IN 15 SECONDS.
PUSH UNTIL ALARM
SOUN DS. DO OR CA N B E
OPENE D IN 1 5 SECO NDS .
PUSH UN TI L AL ARM SOUN D S.
DOOR CAN BE OPENED IN 15
SECO NDS .
PUSH UNTIL ALARM
SOUNDS. DOOR CAN BE
OPENE D I N 1 5 SEC ONDS .
Systems Applications Reference
P:\INSTALLATION INST\Delayed Egress\INST-1511ST\INST-1511ST.vsd Rev E 09-08 Page 11
Activation by a remote trigger for doors with or without latching hardware:
Activation by applying pressure to doors with latching hardware: