Dell SE2717H Installation instructions

SE2717H_ SE2717HR_ SE2717HX 1
1
1. Disassembly Procedures:
Step Figure Remark
S1.The FRONT
VIEW
Turn off power,
Unplug external cables
from product
S2.Remove the
STAND-BASE
ASS’Y
To remove the stand:
1. Press and hold the
stand release button.
2. Lift the stand up and
away from the monitor.
Note:
To prevent scratches on
the LCD screen while
removing the stand,
ensure that the monitor is
placed on a soft, clean
surface.

SE2717H_ SE2717HR_ SE2717HX 2
S3.Remove the
REAR COVER
Use a Philips-head
screwdriver to remove 2
screws for unlocking
mechanisms.
(No.1~2 screw
size=P3x6;
Torque=4±1kgf.cm)
Use Penknife to
separate the bezel and
rear cove follow the
arrows in sequence, then
you can take out rear
cover.
S4.Disconnect the
FFC cable
Disconnect the FFC
cable
S5.Remove the
HEX screws
Use a hex screwdriver to
remove 2 screws for
unlocking mainboard.
(No.1~2 is Hex-screw,
Torque= 4.5±0.5kgf.cm)
12
12

SE2717H_ SE2717HR_ SE2717HX 3
3
S6.Remove the
cables
Remove the cables
S7.Remove the
FFC cable
Remove the FFC cable
S8.Remove the
Mylar
Remove the mylar.

SE2717H_ SE2717HR_ SE2717HX 4
S9.Remove the
Main &Power
Board
Remove the FFC cable
Use a Philips-head
screwdriver to remove 6
screws for unlocking
main board and power
board
(No.1~5 screw
size=D3x6;
Torque=6±1kgf.cm
No.6 screw size=M4x6;
Torque= 6±1kgf.cm)
S10.Remove the
Key Board
Use a Philips-head
screwdriver to remove
3screws for unlocking
Key board.
(No.1~3 screw
size= M2x2.5
Torque=0.9±0.4kgf.cm)
S11.The Panel
The Panel
1 2
3
4
5
6
1 2 3

SE2717H_ SE2717HR_ SE2717HX 5
5
S12.Remove the
screw
Use a Philips-head
screwdriver to remove
1screws for unlocking
main frame
(No.1 screw size= Q3x6
Torque=4±1kgf.cm)
S13.The Main
Frame
The Main Frame
S14.The Bezel
The Bezel
1

SE2717H_ SE2717HR_ SE2717HX 6
S15.Remove
capacitors
Remove electrolyte
capacitors (red mark)
from printed circuit
boards
Take out bulk cap. pin
solder with soldering iron
and absorber
Lift the bulk cap. up and
away from the PCB

SE2717H_ SE2717HR_ SE2717HX 7
7
2. Product material information
The following substances, preparations, or components should be disposed of or recovered
separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components No used
Batteries No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and liquids No used
Plastic containing BFR No used
Component and waste contain asbestos No used
CRT No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps No used
LCD display > 100 cm2 Product has an LCD greater than 100 cm2
External electric cable Product has external cables
Component contain refractory ceramic
fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors
(height > 25mm, diameter > 25mm)
3. Tools Required
Listthetypeandsizeofthetoolsthatwouldtypicallycanbeusedtodisassembletheproducttoapoint
wherecomponentsandmaterialsrequiringselectivetreatmentcanberemoved.
ToolDescription:
‐PhillipheadScrewdriver
‐HexScrewdriver
‐Penknife
‐Solderingironandabsorber