Dell PowerEdge M620 User manual

Dell PowerEdge M1000e, M915, M910,
M710HD, M710, M620, M610x, and M610
Getting Started Guide
Regulatory Model: BMX01, HHB Series, and FHB Series
Regulatory Type: FHB001 and HHB001

Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your
computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if
instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal injury, or
death.
Information in this publication is subject to change without notice.
©2011 Dell Inc. All rights reserved. Printed in the U.S.A.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is
strictly forbidden.
Trademarks used in this text: Dell™, the Dell logo, Dell Precision™, OptiPlex™, Latitude™, PowerEdge™,
PowerVault™, PowerConnect™, OpenManage™, EqualLogic™, Compellent™, KACE™, FlexAddress™and
Vostro™are trademarks of Dell Inc. Intel®, Pentium®, Xeon®, Core®and Celeron®are registered
trademarks of Intel Corporation in the U.S. and other countries. AMD®is a registered trademark and
AMD Opteron™, AMD Phenom™and AMD Sempron™are trademarks of Advanced Micro Devices, Inc.
Microsoft®, Windows®, Windows Server®, Internet Explorer®, MS-DOS®and Windows Vista®are either
trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
Red Hat®and Red Hat®Enterprise Linux®are registered trademarks of Red Hat, Inc. in the United States
and/or other countries. Novell®and SUSE®are registered trademarks of Novell Inc. in the United States and
other countries. Oracle®is a registered trademark of Oracle Corporation and/or its affiliates. Citrix®, Xen®,
XenServer®and XenMotion®are either registered trademarks or trademarks of Citrix Systems, Inc. in the
United States and/or other countries. VMware®, Virtual SMP®, vMotion®, vCenter®and vSphere®are
registered trademarks or trademarks of VMware, Inc. in the United States or other countries. IBM®is a
registered trademark of International Business Machines Corporation.
Other trademarks and trade names may be used in this publication to refer to either the entities claiming the
marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade
names other than its own.
2012 — 03
Rev. A01

Installation And Configuration
WARNING: Before performing the following procedure, review the safety
instructions that came with the system.
Unpacking The System
Unpack your system and identify each item.
Assemble the rails and install the system in the rack following the safety instructions and
the rack installation instructions provided with your system.
Installing The Rails And Enclosure
Figure 1. Installing The Enclosure In The Rack
Assemble the rails and install the enclosure in the rack, following the safety instructions
and the rack installation instructions provided with the enclosure.
3

Installing The Blades
Figure 2. Installing a Blade
Beginning at the top, slide the blades into the enclosure from left to right. When the
blade is securely installed, the handle returns to the closed position.
Connecting The CMC And iKVM Modules
Figure 3. Connecting The Modules
Connect the serial cable and network cable(s) from the management system to the CMC
module. If a second, optional CMC module is installed, connect it as well.
Connect the keyboard, mouse, and monitor to the optional iKVM module.
4

Connecting The System To Power
Figure 4. Connecting Power To The System
Connect the system’s power cables to the system power supplies.
CAUTION: To prevent the power cables from being disconnected accidentally, use
the plastic clip on each power supply to secure the power cable to the power
supply, and use the strap to secure the cable to the strain-relief bar.
Plug the other end of the power cables into a power distribution unit (PDU).
CAUTION: Do not plug the power cables directly into a power outlet; you must use a
PDU. For optimal system functionality, a minimum of three power supplies are
required.
5

Turning On The Enclosure
Figure 5. Enclosure Power Button
Press the power button on the enclosure. The power indicator should light.
NOTE: Once you have connected the system to the power supplies, there may be a
minimal delay before you can turn on your system.
Turning On The Blades
Figure 6. Turning on A Blade
6

Press the power button on each blade, or power on the blades using the systems
management software.
Complete The Operating System Setup
If you purchased a preinstalled operating system, see the documentation associated
with the operating system. To install an operating system for the first time, see the
installation and configuration documentation for your operating system. Be sure the
operating system is installed before installing hardware or software not purchased with
the system.
NOTE: See dell.com/ossupport for the latest information on supported operating
systems.
Dell Software License Agreement
Before using your system, read the Dell Software License Agreement that came with
your system. You must consider any media of Dell-installed software as BACKUP copies
of the software installed on your system’s hard drive. If you do not accept the terms of
the agreement, call the customer assistance telephone number. For customers in the
United States, call 800-WWW-DELL (800-999-3355). For customers outside the United
States, visit support.dell.com and select your country or region from the top of the page.
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with your
system. Warranty information may be included within this document or as a
separate document.
• The Owner’s Manual provides information about system features and describes
how to troubleshoot the system and install or replace system components. This
document is available online at support.dell.com/manuals.
• The rack documentation included with your rack solution describes how to
install your system into a rack, if required.
• Any media that ships with your system that provides documentation and tools for
configuring and managing your system, including those pertaining to the
operating system, system management software, system updates, and system
components that you purchased with your system.
NOTE: Always check for updates on support.dell.com/manuals and read the
updates first because they often supersede information in other documents.
7

Obtaining Technical Assistance
If you do not understand a procedure in this guide or if the system does not perform as
expected, see your Owner’s Manual . Dell offers comprehensive hardware training and
certification. See dell.com/training for more information. This service may not be offered
in all locations.
NOM Information
The following information is provided on the device described in this document in
compliance with the requirements of the official Mexican standards (NOM):
Importer: Dell Inc. de México, S.A. de C.V.
Paseo de la Reforma 2620 -11º Piso
Col. Lomas Altas
11950 México, D.F.
Model number: BMX01
Supply voltage: 100 V CA to 240 V CA
Frequency: 50 Hz/60 Hz
Current consumption: 16 (x6) A
Model number: FHB
Supply voltage: 12 V DC
Current consumption: 75 A
Model number: HHB
Supply voltage: 12 V DC
Current consumption: 37 A
Technical Specifications
NOTE: For additional specifications, see your system Owner's Manual .
8

Power — Blades
Coin-cell battery 3 V CR2032 Lithium coin cell
Power — Enclosure
AC/DC power supply (per power supply
module)
Wattage 2360 W and 2700 W
Connector IEC C20
Heat dissipation 1205 BTU/hr (maximum)
Maximum inrush current Under typical line conditions and over
the entire system ambient operating
range, the inrush current may reach 55 A
per power supply for 10 ms or less.
System Voltage Requirements
NOTE: This system is also designed to be
connected to IT power systems with a
phase to phase voltage not exceeding
230 V.
43 A, 200 V AC to 240 V AC, 50 Hz/60 Hz
(2360 W power supply)
16 A, 100 V AC to 240 V AC, 50 Hz/60 Hz
(2700 W power supply)
NOTE: Heat dissipation is calculated by
using the power supply wattage rating.
Physical — Blades
PowerEdge M915
Height 38.5 cm (15.2 inch)
Width 5 cm (2 inch)
Depth 48.6 cm (19.2 inch)
Weight (maximum) 12.7 kg (28 lb)
PowerEdge M910
Height 38.5 cm (15.2 inch)
Width 5 cm (2 inch)
Depth 48.6 cm (19.2 inch)
Weight (maximum) 13.1 kg (29 lb)
PowerEdge M710 and M610x
9

Physical — Blades
Height 38.5 cm (15.2 inch)
Width 5 cm (2 inch)
Depth 48.6 cm (19.2 inch)
Weight (maximum) 11.1 kg (24.5 lb)
PowerEdge M710HD and M620
Height 18.9 cm (7.4 inch)
Width 5 cm (2 inch)
Depth 48.6 cm (19.2 inch)
Weight (maximum) 7.4 kg (16.3 lb)
PowerEdge M610
Height 18.9 cm (7.4 inch)
Width 5 cm (2 inch)
Depth 48.6 cm (19.2 inch)
Weight (maximum) 5.2 kg to 6.4 kg (11.5 lb to 14.0 lb)
Physical — Enclosure
Height 44.0 cm (17.3 inch)
Width 44.7 cm (17.6 inch)
Depth 75.5 cm (29.7 inch)
Weight (maximum) 178.3 kg (392.2 lb)
Weight (empty) 44.6 kg (98.1 lb)
Environmental
NOTE: For additional information about environmental measurements for specific
system configurations, see dell.com/environmental_datasheets.
Temperature
Operating Continuous operation: 10 °C to 35 °C at
10% to 80% relative humidity (RH), with 26
°C max dew point. De-rate maximum
allowable dry bulb temperature at 1
°C/300 m above 900 m (1 °F per 550 ft).
10

Environmental
NOTE: For information on supported
expanded operating temperature
range and configurations, see
support.dell.com/manuals.
Storage -40 °C to 65 °C (-40 °F to 149 °F) with a
maximum temperature gradation of 20 °C
per hour
Relative humidity
Operating 20% to 80% (noncondensing) at a
maximum wet bulb temperature of 29 °C
(84.2 °F)
Storage 5% to 95% (noncondensing) at a
maximum wet bulb temperature of 38 °C
(100.4 °F)
Maximum vibration
Operating 0.26 Grms at 10 Hz to 350 Hz for 15 min
Storage 1.54 Grms at 10 Hz to 250 Hz for 15 min
Maximum shock
Operating One shock pulse in the positive z axis
(one pulse on each side of the system) of
41 G for up to 2 ms
Storage Six consecutively executed shock pulses
in the positive and negative x, y, and z
axes (one pulse on each side of the
system) of 71 G for up to 2 ms
Altitude
Operating –15.2 m to 3048 m (–50 ft to 10,000 ft)
NOTE: For altitudes above 2950 ft, the
maximum operating temperature is
derated 1 ºF/550 ft.
Storage –15.2 m to 10,668 m (–50 ft to 35,000 ft)
Airborne Contaminant Level
Class G1 as defined by ISA-S71.04-1985
11