Delta Children 23012 User manual

Customer Service: 1-(800)-377-3777
www.DeltaChildren.com
DCPIM06072017
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
INSTRUCTION MANUAL
ADULT ASSEMBLY REQUIRED
THIS PRODUCT CONTAINS SMALL PARTS
STYLES AND COLORS MAY VARY
23012
MULTI-USE
PERFECT FIT
HIGH CHAIR

Customer Service Tel. [phone] www.DeltaChildren.com
2
Child Tray
Seat
Seat Pad
4 Bent Top Leg Seat Tube
4 Center High Chair Extension
Tube
4 Bottom Infant / Toddler Straight
Extension Tube
4 Feet
16"
6 1/4"
Push Button
Lock
Red Part # 50267
Grey Part # 50275
Part # 50277
Part # 50273
Part # 50270
Part # 50272
Part # 50271

4 Feet
Customer Service Tel. [phone] www.DeltaChildren.com
3
FLOOR SEAT ASSEMBLY
WARNING: When not buckled in seat, children can escape and fall suddenly.
WARNING: Always use with the restraint belt.
WARNING: Only use the seat on floor or level ground surface.
WARNING: Never use on raised surfaces such as tables, counters, chairs, beds, or near stairs. Even a
belted baby can cause the seat to slide or move off raised surfaces.
WARNING: Always stay with and watch your baby during use.
WARNING: Never use the floor seat in or near water to avoid drowning.
WARNING: Until child is able to get in and out of the booster seat without help (about 2 1/2 years old), the
child should be secured in the booster seat at all times by the restraining system. The tray is not designed
to hold the child in the chair.
1. Place floor seat on a level floor only never on a
raised surface (Fig. 1).
2. Place child into floor seat and securely fasten
into seat with harness. To tighten harness
position the crotch belt between your child’s
legs. Fasten both waist belts to the buckle on
each side of the crotch belt. Make sure you
hear a “click” on both sides. Check to be sure
the restraint system is securely attached by
pulling it away from your child. The restraint
system should remain attached (Fig 2).
Fig. 1
Fig. 2
Fully Locked
Safety Harness
NOTE: SEAT COVER IS REVERSIBLE
Crotch Belt
Waist BeltWaist Belt

Customer Service Tel. [phone] www.DeltaChildren.com
4
3. To properly install the child safety harness, take
the strap lock and insert strap and entire strap
buckle into the slot on back of chair (Fig 3).
4. Flip seat over and make sure the strap buckle
lays flat and pulls against the back of the chair.
Repeat steps for each (3) strap lock. Make sure
all (3) strap locks and laying flat against chair
bottom. See figure 4 and 4a for reference. For
removal of child harness pull on end strap of
strap lock and glide entire strap lock through
the slots on chair. Repeat (3X) for complete
removal of harness.
Fig. 3
Fig. 4a
Fig. 4
CHILD SAFETY HARNESS
Slot on back
chair

WARNING: When not buckled in seat, children can escape and fall suddenly.
WARNING: Always use with the restraint belt.
WARNING: Only use the seat on floor or level ground surface.
WARNING: Never use on raised surfaces such as tables, counters, chairs, beds, or near stairs. Even a
belted baby can cause the seat to slide or move off raised surfaces.
WARNING: Always stay with and watch your baby during use.
WARNING: Never use the floor seat in or near water to avoid drowning.
Customer Service Tel. [phone] www.DeltaChildren.com
5
INFANT CHAIR ASSEMBLY
Flip floor seat over to see bottom. (Fig 5).
To make sure they are securely locked in
place, pull upward on the bent top leg seat
tube.
"Click"
Fig. 5
1. 2. 3.
Fig. 6
Bent Top Leg Seat Tube
Fully Locked
Position
Push Button
Lock Open
1.
2. Find the bent top leg seat tube, press in the
push button locking tab before sliding the
bent top leg seat tube into seat housing posts.
Once the bent top leg seat tube is fully seated
into the seat housing post, release the push
button locking tab so the locking tab is securely
fastened into the corresponding seat housing
post through hole. The bent top leg seat tube
should also have the seat tube post locked into
the slot on the seat housing post on the back
side of the seat posts. (Fig. 6)
NOTE: SEAT COVER IS REVERSIBLE

Customer Service Tel. [phone] www.DeltaChildren.com
6
INFANT CHAIR ASSEMBLY
"Click"
"Click"
Fig. 7
Fig. 8
Fig. 8a
Fig. 9
Fig. 9d
Fig. 9c
Fig. 9b
Fig. 9a
Straight
Extension
Tube
Fully Locked
Position
3.
4.
5.
Located all (4) feet. Slide each foot onto the
bottom of each infant / toddler straight extension
tube (Fig. 7)
Find all (4) bottom infant / toddler straight
extension tubes with feet attached and push
into all (4) bent top leg seat tubes (Fig 8). Make
sure the push buttons, located at the top of
every tube, are securely locked “clicked” in
place (Fig 8a). To make sure they are securely
locked in place pull upward on extension tube.
Flip over infant chair and place on level
surface. All (4) feet should be flat against
the floor (Fig 9c). Line up left and right child
tray grooves with left and right child seat tray
posts (Fig 9a). Once tray and tray posts are
lined up, rotate tray downward to lock tray
over seat tray locking tabs (Fig 9b). Child tray
is securely locked in place when seat tray
locking tabs "click" into place and are through
tray opening. Pull upward on tray to make
sure in a fully locked position.
• NOTE: Child must be put into seat and
harness must be securely locked in place
around child (Fig 9d). Please refer to Fig 4-5
on page 5 for proper use of harness before
use.
Fully Locked
Safety Harness

Customer Service Tel. [phone] www.DeltaChildren.com
7
CARE AND MAINTENANCE
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF HIGH CHAIR. KEEP
INSTRUCTIONS FOR FUTURE USE. INCORRECT ASSEMBLY MAY MAKE THE HIGH
CHAIR UNSAFE. FAILURE TO FOLLOW THESE WARNINGS AND INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.
WARNING! The child should be secured in the high chair at all times by the restraining system,
either in the reclining or upright position. The tray is not designed to hold the child in the chair. It
is recommended that the high chair be used in the upright position only by children capable of
sitting upright unassisted.
WARNING! Prevent serious injury or death from falls or sliding out.
Always secure child in the restraint.
NEVER leave child unattended.
DO NOT use the high chair until the child can sit up unaided.
DO NOT use the high chair unless all components are correctly fitted and adjusted.
WARNING! Make sure that any harness is correctly fitted.
Only use in a flat stable surface.
Ensure your high chair is fully erected before placing your child inside.
Ensure children are clear of all moving parts before making any adjustments.
NEVER move the high chair with your child inside.
NEVER adjust the seat height with child in high chair.
DO NOT allow your child to climb unassisted into, play with or hang onto your high chair. This is
not a toy.
IMPORTANT! Before assembly or each use of this high chair, inspect this high chair for
damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts
are missing or broken. Never substitute parts. Contact Delta Children’s Products Customer
Service Department at 1.800.377.3777 for replacement parts and instructions if needed.

HIGH CHAIR ASSEMBLY
Find the bent top leg seat tube and push all (4)
tubes into all (4) tube slots (Fig 11). Make sure
the push buttons, located at the top of every tube,
are securely locked “clicked” into place. The push
buttons should be seen through the seat support
posts (Fig 11a). To make sure they are securely
locked in place pull upward on bent top leg seat
tube.
Fig. 10
Fig. 11
Fig. 11a
Bent Top Leg
Seat Tube
"Click"
1. 2. 3.
Fully Locked
Position
Push Button
Lock Open
Customer Service Tel. [phone] www.DeltaChildren.com
8
1.
2.
Flip floor seat over to see bottom. (Fig 10).
NOTE: SEAT COVER IS REVERSIBLE

Customer Service Tel. [phone] www.DeltaChildren.com
9
Find all (4) center high chair extension tubes
and push into all (4) bent top leg seat tubes
(Fig 12). Make sure the push buttons, located
at the top of every tube, are securely locked
“clicked” in place (Fig 12a). To make sure they
are securely locked in place pull upward on
extension tube.
Located all (4) feet. Slide each foot onto the
bottom of each infant / toddler straight extension
tube and place off to side (Fig. 13)
Take all (4) bottom infant / toddler straight
extension tubes with feet attached and push into
all (4) center high chair extension tubes (Fig 14).
Make sure the push buttons, located at the top
of every tube, are securely locked “clicked” into
place (Fig 14a). To make sure they are securely
locked in place pull upward on extension tube.
"Click"
Fig. 12
Fig. 12a
Fig. 13
Fig. 14
Fig. 14a
Center High Chair
Extension Tube
Straight
Extension
Tube
Center High Chair
Extension Tube
"Click"
Fully Locked
Position
HIGH CHAIR ASSEMBLY
3.
4.
5.

Customer Service Tel. [phone] www.DeltaChildren.com
10
Flip over high chair and place on level
surface. All (4) feet should be flat against the
floor (Fig 15c). Line up left and right child
tray grooves with left and right child seat tray
posts (Fig 15a). Once tray and tray posts are
lined up, rotate tray downward to lock tray
over seat tray locking tabs (Fig 15b). Child
tray is securely locked in place when seat tray
locking tabs "click" into place and are through
tray opening. Pull upward on tray to make
sure in a fully locked position.
"Click"
Fig. 15
Fig. 15a
Fig. 15b
Fig. 15c
Fig. 15d
HIGH CHAIR ASSEMBLY
6.
• NOTE: Child must be put into seat and
harness must be securely locked in place
around child (Fig 15d). Please refer to Fig 4-5
on page 5 for proper assembly of harness
before use.
Fully Locked
Safety Harness