DELTA DORE CALYBOX 110 User manual

http://pro.deltadore.com
DELTA DORE TALCO - Bonnemain - 35270 COMBOURG
E-mail : [e-mail]
*2701550_Rev.1*
CALYBOX
User guide
CALYBOX
Energy manager
CALYBOX 120 - 2 zones
CALYBOX 110 - 1 zone
6050388
6050389
Device complying with the requirements of the directives:
CEE 89/336 (Electromagnetic compatibility) and CEE 73/23
modified CEE 93/68 (Low voltage safety)
Because of changes in standards and equipment, the characteristics
given in the text and the illustrations of this document are not binding
unless confirmed by our services.

The required temperature is set on the thermostat of
each heat emitter (convectors, panel heaters, under-
floor heating or radiant ceiling heating, towel warmer
radiators, storage heaters, etc.).
Pilot Wire
order
(mode)
Setting on the heat emitter Room
temperature
Comfort Comfort setting (thermostat knob)
example : 19°C
Economy
Economy setting (thermostat knob)
example : 16°C
or Comfort –X°C
(depending on heat emitter model)
Absence Frost protection set to 7°C or 8°C
(depending on model)
Shutdown Heating shutdown
19°C
16°C
7°C or 8°C
No heating
- 3 -- 2 -
Presentation
This unit optimizes the energy management of your
home:
• Comfort or Economy mode programming of the hea-
ting for 1 zone (CALYBOX 110) or 2 zones (CALYBOX
120),
• reduction in the subscription costs by preventing the
circuit-breakers from tripping when the electricity
consumption is too great (load shedding),
• indication of the electricity consumption of the system.
To control the heat emitters, the programmer uses the
Pilot Wire.
Independent from the power supply of the heat emitter,
the Pilot Wire is used to send the Comfort ,
Economy, Frost Protection or Shutdown
orders requested by the programmer.
IMPORTANT:The heat emitter must be in automatic
mode (PROG, AUTO, , etc. depending on model).
Pilot wire
Pilot Wire orders
Heat emitters
Programmer

Contents
• Carefully read these instructions prior to use.
• Do not attempt to repair the unit yourself; after-
sales service is available.
Warnings
Options
TYWATT 500 (ref. : 6110014)
Depending on your installation, the TYWATT 500, toge-
ther with the CALYBOX, allows you to know the electri-
city consumption (in euros) of the heating, the water
heater (DHW) and other electrical appliances (lights,
household appliances, etc).
TYPHONE 500 (ref. : 6201029)
Combined with the CALYBOX, the TYPHONE 500 is
used to control the heating system and the water hea-
ter (DHW) remotely by telephone.
MINOR 500 (ref.: 6151041)
Regulates an underfloor heating or radiant ceiling hea-
ting system. In combination with the CALYBOX, this
unit is used to control the set points and determine the
room temperature measured by each probe.
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Automatic mode . . . . . . . . . . . . . . . . . . . . . . . .7
Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Continuous mode . . . . . . . . . . . . . . . . . . . . . .10
Absence mode . . . . . . . . . . . . . . . . . . . . . . . .11
Shutdown mode . . . . . . . . . . . . . . . . . . . . . . .12
Information button . . . . . . . . . . . . . . . . . . . . .13
Time setting . . . . . . . . . . . . . . . . . . . . . . . . . .15
Programming . . . . . . . . . . . . . . . . . . . . . . . . . .16
1. Create your program . . . . . . . . . . . . . . . . . . . . .16
2. Copy the program . . . . . . . . . . . . . . . . . . . . . . . .16
3. Confirm the program . . . . . . . . . . . . . . . . . . . . .16
MINOR 500 option . . . . . . . . . . . . . . . . . . . . . .19
Tempo tariff . . . . . . . . . . . . . . . . . . . . . . . . . .20
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .21
- 5 -- 4 -

- 7 -
Turn the knob to AUTO.
CALYBOX 110 follows the programming.
CALYBOX 120 follows the programming in both zones.
Automatic mode
Override
Information button
Display in automatic mode
Time
Current mode
Room
temperature
Current day
Override for zone 1
Override for zone 2
Information button
Time
Current day
Room
temperature
Current mode in zones
1 and 2
Display in automatic mode
- 6 -
Description
Modification
buttons
Selector
knob position
Selector
knob
Shutdown mode
Absence mode
Timer mode
Automatic mode
Continuous mode
Time setting
Programming
These instructions apply to both CALYBOX 110 and
CALYBOX 120.

- 9 -
Timer mode
Choice of the zone on the CALY B OX 120
(the other zone follows the AUTO mode))
Choice of mode:
Economy or Comfort
Confirm
Return to AUTO mode at
the end of the countdown
Confirm
To cancel the current timer mode,
turn the knob..
This mode is used to select a mode for a given time and
for one zone only.
Tu r n the knob to .
Adjustment of the duration from 15 minutes
to 72 hours (in increments of 15 minutes)
Confirmation and
start of the countdown
Override
- 8 -
In automatic mode, override is used to go from
Comfort to Economy mode (or conversely) until the
next program change.
Press the override button
of zone 1.
00:0000:00 17:0015:30 23:00
6:00 8:00
Current override
on zone 1.
At 17:00, the program will
return to its usual program.
To cancel the current override,
press the button once more.
Example: it is 15:30 and you would like to switch
to Comfort mode before the set time (17:00).
Current day programming on zone 1

Room
temperature
Current modes in
zones 1 and 2
Modification of the
mode in zone 1
Modification of the
mode in zone 2
Room
temperature
Current mode
Modification
of the mode
This mode allows you to choose a continuous mode for
each of the zone.
Turn the knob to , then press the modification but-
ton of the relevant zone to select the Comfort or
Economy mode.
CALYBOX 110
CALYBOX 120
To exit this mode, turn the knob.
Adjustment of the number of days
(1 to 365)
Return to AUTO mode at
the end of the countdown
To cancel the current absence
mode, turn the knob.
This mode lets you place your home under Frost Protection
if you need to leave for several days
Confirm and start the calendar
countdown.
Tu r n the knob to .
Example: for a departure on 1 March
and a return on 10 March, program 9
days of absence.
Automatic operation will resume
on 10 March at midnight.
- 11 -
Absence mode
NOTE:The water heater (DHW) is shutdown during
the absence mode.If you want the water heater to be
in automatic mode, refer to the “installation guide” or
contact your installer or our customer service depart-
ment.
- 10 -
Continuous mode

During the AUTO, or modes, press the i button
repeatedly to find out:
• total consumption of your installation,
to reset, press and hold the init. button for 5 seconds.
• if you have the TYWATT 500 option,
the electrical consumption in euros of the heating, the
water heater (DHW) and other electrical appliances
(lights, household appliances, etc).
Information button
Reset
Consumption
Press successively
Mise à zéro
Mise à zéro
- 12 -
This mode allows you to shut down your heating sys-
tem (in this case, the water heater stays in automatic
mode).
Turn the knob to .
Shutdown mode
Room
temperature
- 13 -

Turn the knob to .
The days flash.
Press + or - to change the day, then press OK to
confirm and continue on to the next setting.
Repeat the operations to set the hours and minutes.
To leave the “setting the time” mode, turn the knob.
Minutes
Hours
Days
(1 : Monday… 7 : Sunday)
Time setting
- 15 -
NOTE: If the unit is configured for a daily program, the
days setting is not offered.
- 14 -
• the program of the current day per zone,
• if you have the MINOR 500 option,
the temperature measured by each of the probes
declared during the installation.
Indication of a probe or
probes on the installation
probe no.
temperature
measured
by the probe
Comfort periods
Information button

Press until you reach 6:00
Press until you reach 8:00
Press until you reach 17:00
Press until you reach 23:00
Press until you reach 00:00
Copy and confirm
or confirm
00:00
Example: Comfort from 6:00 to 8:00 and from 17:00 to 23:00
00:00
23:00
17:00
8:00
6:00
Programming
Turn the knob to PROG.
The default program is a Comfort period from 6:00 to
23:00.
1. Create your program
Programming starts on day 1 at midnight.
Press the or buttons to create different Economy
or Comfort periods
2. Confirm and copy the program
Press and hold the OK button for 3 seconds to confirm
the program you created and copy it to the next day.
3. Confirm the program
Press the OK button to confirm and continue on to the
next day to program it separately.
Day
1st time slot
Comfort period
adjustment
Economy period
adjustment
Available on the
CALYBOX 120
- 16 - - 17 -

MINOR 500 option: set point settings
Setting (5 to 30°C) of the Comfort set
point (19°C by default) for the probe 1 of
zone 1.
Setting (5 to 30°C) of the Economy set
point (16°C by default) for the probe 1 of
zone 1.
Confirm and go to the next setting.
Confirm and go to the set point settings
for the next probe.
Repeat the operations for each probe.
When the last probe is set, you can set the Frost
Protection set point for all the zones.
To exit the mode, turn the knob to another mode.
This mode is used to modify the Comfort and Economy set
points of each probe. Tu r n the knob to .
Setting (5 to 15°C) of the Frost Protection
set point (8°C by default) for all the zones.
Confirm the modification
- 19 -- 18 -
Programming
Check your program
Press the button repeatedly to check the accuracy
of the Comfort and Economy periods you created.
Programming zone 2 (on the CALYBOX 120)
The programming for zone 2 is available after pressing
(OK) of the day 7 of the zone 1
Exiting the programming mode
Turn the knob to another mode
Program
profile Verification of the
different or
periods
Time slot
consulted
COMMENTS:Depending on the configuration made
during installation, programming can be weekly or
daily.Likewise, this programming may be done in
increments of one hour, 30 minutes, or 15 minutes. To
change these settings, refer to the “installation guide”,
or contact our customer service department or your
installer.

Nothing is displayed on the room unit screen.
There is no power supply.
Check your circuit breaker.
The i symbol flashes.
A fault has been detected in the system.
Press the button to consult the fault or faults.
The unit displays: dEF and a number.
There is a fault on the unit or the installation.
Contact your installer or our customer service department.
The unit displays ---- instead of the temperature measu-
red by each MINOR 500 probe.
There is a communication problem with the probes.
Contact your installer or our customer service department.
The unit is in time setting mode.
There was a mains disruption that lasted more than 2 hours.
Set the time.All other settings have remained unchanged.
Troubleshooting
- 21 -
The purpose of this section is to help you quickly solve
the most common problems that you may encounter
with your product during use.
If you're unsure, or if the problem persists or isn't in
this list, contact our customer service department.
- 20 -
If you are on the tempo tariff, you can program specific
modes for peak or off-peak days according to the confi-
guration made during installation.
To know or change these settings, refer to the “installa-
tion guide”, or contact our customer service depart-
ment or your installer.
The symbol flashes during a tariff reduction.
The symbol flashes if you are in Médio (1°C) or
Modérato (-2°C) comfort mode
Tempo tariff
Ta r iff reduction
in progress

The symbol and flash.
You are in tariff reduction mode.
Refer to the Tempo tariff section.
When setting the time,there is no option to set the day.
You are in daily programming.
To switch to weekly programming, refer to the installation
guide or contact your installer or our customer service depart-
ment.
The consumption displayed by the unit does not cor-
respond to the consumption shown on the bill sent by
the electricity supplier.
The consumption value that you can read on the unit is a
non-contractual indication and cannot be substituted for the
consumption value mentioned on your electricity supplier’s
bill.
Refer to the installation guide to check the price per kWh or
contact your installer or our customer service department.
The heating elements are in Frost Protection mode
You are in programming mode, the absence mode or time
setting mode.
Turn the knob to select another mode.
Pb ---- is displayed on the screen.
Problem with the connection of a heating element.
Contact your installer or our customer service department.
Troubleshooting
- 22 - - 23 -
The unit displays HEAT
Your underfloor heating or radiant ceiling heating system is in
“gradual heating” mode.
If you want to know the number of days remaining, press the i
button.
The temperature displayed does not match the tempera-
ture measured in the room (thermometer).
It is possible to correct this.
Refer to the installation guide or contact your installer or our
customer service department.