DELTA DORE DELTA 8000 TA BUS User manual

Installation instructions
EN Zone thermostat for Underoor heating
DELTA 8000 TA BUS

EN
32
• Power supply by the bus, 24V
• Bus Input/output 2 wires
• Class III insulation
• Surface-mounted or on ush-mounting box
• Dimensions: 81 x 88 x 21 mm
• Degree of protection: IP 30
• Operating temperature: 0 to +40°C
• Storage temperature: -10 to +70°C
• Installation in an environment with normal
pollution levels
TECHNICAL CHARACTERISTICS CONTENTS
1/ Location/Mounting 4
2/ Association of the thermostat
with the technical unit. 7
3/ Conguring the room
thermostat 9
4/ Initialisation 14
4.1 Deleting all the association bus
with the technical unit 14
4.2 Deleting the association of the
thermostat with the technical unit 16
4.3 Initialising the room thermostat
settings 17

EN
54
~1,50 m
Mini 20 cm
1
4
2
3
Since the temperature measurement sensor is
inside the unit, you must install the thermostat
ush-mounting box:
- on an accessible wall at a height of 1.50 m
- away from heat sources (replaces, sunlight)
and draughts (windows, doors)
IMPORTANT: Do not install the thermostat on
a wall in contact with the outdoors or with an
unheated room (e.g. garage, etc.)
The sleeve output in the ush-mounting box must
be blanked off (with mastic) in order to avoid
unwanted air movements that would cause the
sensor reading to be inaccurate.
❶ Separate the unit from its base by pushing the
pin using a screwdriver.
❷Connect the bus to the terminal on the base
❸ Mount the base to the ush-mounting box.
❹ Ret the thermostat back on its base.
1/ LOCATION/MOUNTING

EN
76
2/ ASSOCIATION OF THE THERMOSTAT
WITH THE TECHNICAL UNIT.
❶Press and hold the 1st and the 4th button
for 3 seconds. Release.
❷The screen displays CF20.
Press OK then press + and - to select the
output with which the room thermostat will be
associated.
Conrm with OK.
❸The screen displays CF21.
Select the transmitter and press OK.
❹The screen displays CF05.
Select the thermostat type and press OK.
Output
number
1 to 16 depending on
the system.
Transmitter
type
0Underoor heating
(by default)
1 Heater
2Ceiling or ductable
(2) Thermostat
type
0Zone thermostat
1 Master thermostat
(2) CF05: the Master thermostat enables the
centralised use of ON/OFF and HEAT/COOL (at
least one Master thermostat is required in an
installation without a programmer).
3 s
12

EN
98
3/ CONFIGURING THE ROOM
THERMOSTAT
❶From the OFF mode.
Press and hold the 2nd
button from the left for
5 seconds.
Release.
❷Tap the OK button.
Release.
❸The screen displays CF01.
• Press + or - to select the
menu.
• Press OK to enter the
setting mode, then + and - to
perform the setting.
Temperature
management
On/Off
management
HEAT/
COOL
mode
manage-
ment
Master
thermostat
On the
controlled
zone
On all zones On all
zones
Zone
thermostat
On the
controlled
zone
On the
controlled
zone
-
5 s

EN
1110
Correction of the measured
temperature +/- 5°C in 0.1°C increments (0°C by default)
Temperature displayed in normal mode 0 Setting display (default selection)
1Display of the measured temperature.
(1)
Ban on the Cool regulation on the
thermal zones of the Room Temperature
(if SW2 = ON)
0 No ban (default selection)
1 Ban
Display the status (ON) of the
associated output
0 No (default selection)
1Yes
(2) Thermostat type 0 Zone thermostat (default selection)
1 Master thermostat
(1) CF03 only appears in Heat/Cool production mode
(SW2=ON, refer to the technical unit manual) and
for underoor heating (CF21 =0) or for ceiling/
ductable (CF21 = 2).
(2) CF05: the Master thermostat enables the
centralised use of ON/OFF and HEAT/COOL (at
least one Master thermostat is required in an
installation without a programmer).
3/ CONFIGURING THE ROOM
THERMOSTAT

EN
1312
Activation of the window/door magnetic contact
function (the room thermostat switches to Frost
Protection mode if the window/door magnetic
contact is activated).
0Not activated
1Activated (default selection)
'Presence detection' function
(the thermostat lowers its setting in the
event that no presence is detected).
0Not activated
1Activated (default selection)
Standby mode
0Display off after a 10 seconds time-out
period
1Display illuminated continuously (default
selection)
Backlighting
0Deactivated
1When activated, it goes out after a 5-second
time-out period (default)
Output number 1 to 16 depending on the system. '--' is displayed if
none are allocated.
Transmitter type
0 Underoor heating (by default)
1 Heater
2Ceiling or ductable
Heating percentage limitation From 10 to 100% in increments of 10
(100%= No limitation, by default).
3/ CONFIGURING THE ROOM
THERMOSTAT

EN
1514
5 s 3 s
3 s
4/ INITIALISATION
4.1 DELETING ALL THE ASSOCIATION BUS
WITH THE TECHNICAL UNIT
❶From the OFF mode.
Press and hold the 2nd button from the left for
5 seconds. Release.
❷Press and hold the 2nd button from the left
again for 3 seconds. Release.
❸The screen displays Ln01. Press + to display
Ln05.
❹Press OK. The screen displays rSt.. Press and
hold OK for 3 seconds.
rSt ashes for 2 seconds.
Release.
❺Press MODE to exit.

EN
1716
4.2 DELETING THE ASSOCIATION OF THE
THERMOSTAT WITH THE TECHNICAL UNIT
Press OK to open the setting, then press + and - to
select «= --».
Conrm with OK.
4.3 INITIALISING THE ROOM THERMOSTAT
SETTINGS
This menu restores the system
to factory settings.
❶From the OFF mode.
Simultaneously press the 1st
and 3rd buttons from the left
(i) for 10 seconds. The screen
displays rSt1. Release.
❷Press and hold OK for
3 seconds until the rSt display
ashes. Release.
The system automatically
returns to OFF mode.
4/ INITIALISATION
10 s
3 s
10 s
3 s
10 s 3 s

www.deltadore.com
09/18