DELTA DORE PACK TYBOX 5000 User manual

Installation instructions
EN
Pack TYBOX 5000

2 3
EN
ContentComposition
mesurée
18.4°C
SALON
CHAUFFAGE
19.0°C
or
Your PACK comprises:
- 1 TYBOX 5000 connected room unit
- 1 TYDOM Home and its connector
1/ Location.................................................................................................................. 4
2/ Connection............................................................................................................ 5
2.1 Circulator control ................................................................................................... 5
2.2 Control of the thermostat input of the boiler
or heat pump (HP) no-reversible .............................................................................. 5
3/ Mounting ............................................................................................................... 7
4/ Installation............................................................................................................ 8
4.1 TYDOM Home ........................................................................................................ 8
4.2 Associate the TYDOM applicaon
with the Connected TYBOX 5000 connecté......................................................... 9
5/ Conguration ....................................................................................................... 11
6/ Troubleshooting .................................................................................................. 13
6.1 Signals and possible faults
on the wireless room thermostat TYBOX 5000 ................................................... 13
6.2 Signals and possible faults on the TYDOM Home ......................................... 14
7/ Technical characteristics.................................................................................. 16

4 5
EN
1/ Location 2/ Connection
Since the temperature measurement sensor is inside the box, you must install the
thermostat ush-mounting box:
- on an accessible wall at a height of 1.50 m
- away from heat sources (replaces, sunlight) and draughts (windows, doors)
IMPORTANT: Do not install the thermostat on a wall in contact with the outdoors
or with an unheated room (e.g. garage, etc.) The sleeve output in the ush-
mounting box must be blanked off (with mastic) in order to avoid unwanted air
movements that could bias the sensor reading.
2A max. / 230V~
TYBOX 5000
2A max. / 230V~
NL
2A max. / 230V~
Circulator
The diagrams provided are simplied for greater clarity. Protections and other
accessories required by standards are not illustrated. - Standard NF C15-100
and good practice must be complied with. Connected or nearby units must not
generate excessive interference (directive 89/336/EEC).
2.1 Circulator control
2A max. / 230V~
TYBOX 5000
2A max. / 230V~
NL
2A max. / 230V~
HP
Thermostat
input
2A max. / 230V~
TYBOX 5000
2A max. / 230V~
NL
2A max. / 230V~
Boiler
Thermostat
input
2.2 Control of the thermostat input of the boiler
or heat pump (HP) no-reversible
~1,50 m
Mini 20 cm
1
3
2

6 7
EN
2/ Connection
❶ Remove the terminal, on the back of the device, using a screwdriver.
❷ Connect the terminal to the control wire (circulator, boiler or heat pump
thermostat input).
❸ Fit the terminal back into its position.
3/ Mounting
❶ Remove the thermostat cover by pushing the pin using a screwdriver.
❷ Attach the base by using suitable xings for mounting. Fit the cover back onto
the thermostat.
❸ Insert the batteries, with the right polarity
1 2
3
2 x 1,5V - AAA LR03
Click
Click
2
3
1
4

8 9
EN
4/ Installation
4.2 Associate the TYDOM application
with the Connected TYBOX 5000 connecté
Go to the «Settings» page of your installation, select «Add a device», then
follow the instructions.
4.1 TYDOM Home
4.1.1 Box contents
A. Tydom Home
B. Ethernet cable
C. Mains supply
D. Important Product Information
4.1.2 Description
E. System status display LED
F. Ethernet port
G. Mains power socket
H. Conguration/Information button
4.1.3 Installation
❶Connect your Tydom Home by STRICTLY following this order:
① connect the Ethernet cable (B).
② then, connect the mains power (C)
❷Download the Tydom app.
- Log in to either the Google Play or App Store,
depending on your device.
- Search for and download the free Tydom app.
❸Activate the Wi-Fi connection on your
smartphone or tablet, and connect to the same
local network as your Tydom Home.
❹Congure the Tydom app.
- Note the last 6 characters of your Tydom Home’s
MAC address.
- Log in to the app and follow the instructions.
MAC: 001A25xxxxxx
MAC : 001A25FFFF123456
MAC : 001A25 xxxxxx
A B C D
F
E
G H
B
C
30 cm
min.
Box ADSL

10 11
EN
5/ Conguration
This menu is used to determine all the settings adapted to your installation.
❶To enter conguration mode, press the MODE button for 10 seconds until the
screen displays CF01.
❷Press +or - to set.
❸Briey press MODE to go to the next menu.
Press MODE or wait 5 seconds to exit.
CF01 - Correcting the temperature measured
Setting from -5°C to +5°C
Example: If the temperature displayed by the unit is 15°C and the actual
temperature (thermometer) is 16°C, set +1°C.
CF02 - Settings lock
0No locking (default setting)
1Total locking
2Partial locking. Modication of the temperature setting at +/-2°C
The screen will display ‘____’ if it is locked
To unlock (selection 1 and 2), simultaneously press + or - the buttons for 10
seconds.
CF04 - Frost protection mode temperature setting
Setting of 5°C to 15°C. Default value: 10°C.
CF05 - Type of temperature displayed in AUTO mode
0Temperature setting display (default selection)
1Display of the measured room temperature.
1: Pressing the + or - button once displays and sets the temperature setting (in ON
mode).
CF06 - Regulation time base
15 15 minutes (default settings)
30 30 minutes
45 45 minutes
60 60 minutes
On/Off On/Off
CF07 - Modication of the on/off regulation hysteresis
Only displayed if menu CF06 = on/off
Setting of 0.2°C to 2°C. Default value: 0.4°C
CF08 - Anti-seize function
The Anti-seize function activates the circulator 1 minute per day to prevent any
seizing up during a non-heating period.
0 Anti-seize disabled
1Anti-seize enabled (default settings)

12 13
EN
6.1 Signals and possible faults
on the wireless room thermostat TYBOX 5000
• When you press a button, the screen displays: ____
Access to the settings is locked.
To unlock, press and hold the + and - buttons for 10 seconds.
IMPORTANT:
if you want to lock the device again, refer to the conguration menu (CF02).
• The screen displays the low battery symbol . Replace the batteries.
The batteries are spent.
5/ Conguration
CF09 - Reversal of relay direction
The relay contact is normally open. It closes during a heating request. You can
reverse the direction of operation.
0Normally open (default selection)
1Normally closed
CF10 - Return to initial settings
This menu resets all the CF01 to CF09 settings to their default value.
By default CF10 = 0.
To reset, press + to display 1 and conrm by pressing MODE.
Association with a door/window magnetic contact (DO / MDO / DOI TYXAL+)
If a door/window magnetic contact (e.g. window) is associated with the TYBOX
5000, the heating switches to Frost Protection mode when an open window is
detected.
❶ Press the +and MODE buttons simultaneously until the screen shows
for example rF00.
❷ On the door/window magnetic contact, press the button.
❸ Check that the screen evolved and shows rF01 on TYBOX 5000.
mode
6/ Troubleshooting
2 x 1,5V - AAA LR03
mode
mode
> 3s
1 2 3
mode / +mode / +

14 15
EN
6/ Troubleshooting
6.2 Signals and possible faults on the TYDOM Home
LED System status
Flashing white System accessible locally and remotely, user connected
Steady white System accessible locally and remotely
Flashing orange System accessible locally, user connected
Steady Orange System accessible locally
Steady Red No IP address allocated
Advanced functions
Below are the functions accessible depending on how long the button on the back of
your Tydom Home is pressed..
A Secure connection and viewing connection status
Briey press the buon. LED displays for 10 seconds.
Flashing yellow Stac IP mode
Flashing blue DHCP mode
Flashing blue (3x)
DHCP in progress Check the DHCP acvaon on the router
Flashing red No network connecon Check the Ethernet link
B Change from static IP to DHCP
Press the buon for 3 seconds unl the pink LED ashes
slowly. Release.
3’’ >
15’’
>
30’’
>
BA C
Static IP -> DHCP
Advanced functions
RESET
C Reset to factory settings
Press the buon for 30 seconds unl the LED stops ashing. Release.
System status - DHCP mode
- Clear product associations

16 17
EN
The connection quality of the product may be affected by different modications of the IP architecture on which it
operates. These modications can be, but are not limited to, a change of hardware, a software update or conguration,
work conducted on your operator’s equipment or any other multimedia equipment such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the United States and in other countries, and is used under licence.
AndroidTM and Google Play are Google LLC registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment, the characteristics given in the text and the illustrations in this
document are not binding unless conrmed.
7/ Technical characteristics
Wireless room thermostat TYBOX 5000
• Contact output 2A (230V)
• Ball test: 125 ° C
• Rated surge voltage: 4000V
• Powered by 2 lithium batteries 1.5V, LR03/AAA (supplied)
• Class III insulation
• Radio frequency 868.7 MHz to 869.2 MHz
• Maximum wireless power: <10 mW
• Wireless remote control device
• Wireless range: 100 to 300 metres outside, variable depending on the associated
equipment (the range can vary depending on the installation conditions and the
electromagnetic environment)
• Dimensions: 80 x 84 x 21 mm
• Degree of protection: IP 20
• Wall mounting
• Installation in an environment with normal pollution levels
• Storage temperature: -10 to +70°C
• Operating temperature: 0 to +55°C
Smart home hub TYDOM Home
• Power supply via AC adapter Ktec: KSAS0050500100VED
or SPC: ZZU1001-10050-2E
AC values: 100-240V~ 50/60 Hz, 0,18A - DC: 5V 1A
Only these adapters should be used with the Tydom Home.
• Maximum consumpti on (without USB connection): 0.9 W
• Radio frequency 868.7 MHz to 869.2 MHz
• Maximum wireless power < 10 mW
• Category 2 receiver
• Wireless range: up to 300 metres outside, variable depending on the associated
equipment (the range can vary depending on the installation conditions and the
electromagnetic environment)
• Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
• Class III insulation
• Dimensions: 100 x 100 x 30 mm
• Degree of protection: IP 30
• Operating temperature: -10 to +40°C
• Storage temperature: -20 to +70°C
• Installation in an environment with normal pollution levels

www.deltadore.com