Delta Electronics 1x9 Bi-Directional Transceiver Module... User manual

OPBD-155E1J1R
DELTA ELECTRONICS, INC.
1 Revision: S2
03/09/2007
www.deltaww.com
1x9 Bi-Directional Transceiver Module for Fast
Ethernet, ATM, SONET OC-3/SDH STM-1
FEATURES
 RoHS compliant
 Industry Standard 1 x 9 Footprint
 Single Mode Fiber, Bi-Directional
Transmission with 1310nm Transmitter and
1550nm Receiver
 Link Distance up to 15km
 Single +5V power supply and PECL logic
interface
 Wave Solderable and Aqueous Washable
 Bellcore GR-468 compliant
 Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Description
DELTA’s 1x9 Bi-Directional transceiver is
designed for point-to-point Bi-Directional Optical
Network transmission. The module consists
1310nm FP laser, InGaAs PIN, Preamplifier and
WDM filter in a high-integrated optical
sub-assembly, and it receives up to 155Mbps of
continuous data at 1550nm, and transmits
155Mbps of continuous data at 1310nm.
The module is contained in a 1x9 industry
standard package with a SC receptacle connector,
and support PECL electrical signal Interface and
receiver signal detect output.
Application
 TTC TS-1000
 ITU-T G.985
 IEEE 802.3ah 100BASE-BX/ Fast Ethernet
 SONET OC-3/SDH STM-1/ ATM Network
 FTTx Broadband Access System
Performance
 OPBD-E1J1R data link up to 15km in 9/125um
single mode fiber.

OPBD-155E1J1R
DELTA ELECTRONICS, INC.
2 Revision: S2
03/09/2007
www.deltaww.com
0.85
1.20
0.80
1.00
0.50
0.20
0.00
-0.20
Amplitude
0.350.150.00
Time
0.65
Mean level of logical "0"
1.00
Mean level of logical "1"
Opt
i
ca
l P
u
l
se
M
as
k
w
i
t
h B
esse
l Fil
te
r
Spec
ifi
ed
in IT
U
-T
G.957
1. Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC
Operating Ambient Temperature Ta -10 80 ºC
Storage Ambient Humidity HA5 95 %
Power Supply Voltage VCC -0.5 6 V
Signal Input Voltage -0.3 Vcc+0.3 V
Optical Input Power (Peak) 0 dBm
Lead Soldering Temperature TSOLD 260 ºC
Lead Soldering Time tSOLD 10 sec
2. Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Note
Ambient Operating Temperature TA0 70 ºC
Without air flow
Ambient Humidity HA5 85 %
Non-condensing
Power Supply Voltage VCC 4.75 5 5.25 V
Power Supply Current ICC 250 mA
Power Supply Noise Rejection 100 mVp-p 100Hz to 1MHz
Data Rate 10 155.52 Mbps
Transmission Distance 15 km
3. Optical Specification of Transmitter
Parameter Symbol Min. Typ. Max. Unit Note
Average Launched Power PO-14 -11 -8 dBm Note (1)
Launched power (Peak.) -5 dBm
Extinction Ratio ER 8.5 dB
Center Wavelength λC1260 1310 1360 nm FP Laser
Spectrum Width (RMS) σ6
nm
Optical Rise/Fall Time tr/tf1.3 ns Note (2)
Total Jitter tJ1 ns Note (3)
Optical Return Loss Tolerance ORLT 14 dB
Relative Intensity Noise RIN -116 dB/Hz
Output Eye Mask Compliant with Bellcore TR-NWT-000253
and ITU recommendation G.957 Note (4)
Note (1). Launched power (avg.) is power coupled into a single mode fiber.
Note (2). These are unfiltered 20-80% values.
Note (3). Measure at 223-1 NRZ PRBS pattern
Note (4). Eye Mask definition

OPBD-155E1J1R
DELTA ELECTRONICS, INC.
3 Revision: S2
03/09/2007
www.deltaww.com
4. Optical Specification of Receiver
Parameter Symbol Min. Typ. Max. Unit Note
Input Optical Wavelength λIN 1480 1600 nm PIN-PD
Receiver Sensitivity PIN -30 dBm Note (1)
Input Saturation Power (Overload) PSAT -3 dBm
Signal Detect -Assert Power PA- -30 dBm
Signal Detect -Deassert Power PD-44 dBm Note (2)
Signal Detect Hysteresis PA-PD0.5 2.5 6 dB
Optical Receiver Reflectance -14 dB Note (3)
Output Data Rise/Fall time tr/tf1.5 ns Note (4)
S/X Endurance 10 dB Note (5)
Optical Isolation 25 dB Note (6)
Note (1). Measured with 1520nm, ER=10dB; BER =<10-10@PRBS=223-1 NRZ
Note (2). When SD deasserted, the data output is Low-level (fixed)
Note (3). When the terminal is viewed from the optical path, the reflection toward the optical path of the
optical signal with a central wavelength of 1480nm to 1580nm transmitted to terminal.
Note (4). These are 20%~80% values
Note (5). X=10 MHz, Rectangular BER =10-10
Note (6). Receiver isolation between 1260nm ~1360nm
5. Electrical Interface Characteristics
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Total Supply Current ICC A mA Note (1)
Differential line input Impedance RIN 80 100 120 Ohm
Differential Data Input Swing VDT 300 1600 mVp-p
Data Input Voltage- High VIH-VCC -1.165 -0.880 V
Data Input Voltage- Low VIL-VCC -1.810 -1.475 V PECL
Receiver
Total Supply Current ICC B mA Note (1)
Differential Data Output Swing VDR 400 2000 mVp-p
Data Output Voltage-High VOH-VCC -1.085 -0.880 V
Data Output Voltage-Low VOL-VCC -1.830 -1.555 V
Signal Detect Output Voltage-High VOH-VCC -1.085 -0.880 V
Signal Detect Output Voltage-Low VOL-VCC -1.830 -1.555 V
PECL
Note (1). A (TX)+ B (RX) = 250mA
(A: Not include termination circuit; B: using a resister of 270Ωbetween Data-output and ground)

OPBD-155E1J1R
DELTA ELECTRONICS, INC.
4 Revision: S2
03/09/2007
www.deltaww.com
6. Pin Description
Tx/Rx Pin No. I/O Pin Name Description
1 VeeR Receiver Ground
2 O RD(n) Inverted Receiver Data Output
3 O RD(p) Non-Inverted Receiver Data Output
4 O SD
Normal Optical Input indicated by logic “High”, and No Optical
Input indicated by logic “Low”.
Rx
5 VccR +5V Receiver Power Supply
6 VccT +5V Transmitter Power Supply
7 I
TD(p) Non-Inverted Transmitter Data Input
8 I
TD(n) Inverted Transmitter Data Input
Tx
9 VeeT Transmitter Ground
MS Mounting studs/ connect this pin to Chassis ground
Bottom View
MS
MS
1
2
3
4
5
6
7
8
9

OPBD-155E1J1R
DELTA ELECTRONICS, INC.
5 Revision: S2
03/09/2007
www.deltaww.com
7. Recommended Interface Circuit (AC Coupling)
C1/2/3 =4.7uF
C4/5/6/7 = 100 nF
L1/2 =1uH
R1/2 =68Ω(If C4/5=0, then R1/2 =82 Ω, it is for DC-coupled.)
R3/4 =180Ω(If C4/5=0, then R3/4 =130 Ω, it is for DC-coupled.)
R7/8 =270
Ω
WR5/6/9/10/11/12 Depend on SerDes chip used
R13 =510Ω
Value of R5/6/9/10/11/12 may vary as long as proper 50 Ωtermination or differential 100 Ωis
provided. For good EMI performance, the power supply filter is required. Use shorter tracks from the
inductor L1/2 to the module VccTx/VccRx .
Laser
Driver
LIMITING
Amp lif i er
Serializer/
Deserializer
ECL/PECL
DRIVER
Receiver
PLL etc.
VCC
TX+
TX-
RD-
RD+
VCC SerDes
3.3V
TXGND
TxD
TxD
VCCRx
VCC SerDes
3.3V
Pre-
Amp
SD
RxD
RxD
RxGND
VCCTx
Delta Transceiver
C2
C1 L2
L1
Signal detect
S D to upper leve l
R13
R12
R9
R10
R11
R6
R5
R3
R4 R2
R1
R7 R8
C3
C6
C7
C4
C5
1
2
3
4
5
6
7
8
9
5V
5V
Laser
Driver
LIMITING
Amp lif i er
Serializer/
Deserializer
ECL/PECL
DRIVER
Receiver
PLL etc.
VCC
TX+
TX-
RD-
RD+
VCC SerDes
3.3V
TXGND
TxD
TxD
VCCRx
VCC SerDes
3.3V
Pre-
Amp
SD
RxD
RxD
RxGND
VCCTx
Delta Transceiver
C2
C1 L2
L1
Signal detect
S D to upper leve l
R13
R12
R9
R10
R11
R6
R5
R3
R4 R2
R1
R7 R8
C3
C6
C7
C4
C5
1
2
3
4
5
6
7
8
9
5V
5V

OPBD-155E1J1R
DELTA ELECTRONICS, INC.
6 Revision: S2
03/09/2007
www.deltaww.com
8. Outline Dimensions
Parameter Unit Description Note
Mechanical Dimensions mm 50.4x25.4x10.8
Connector Type - SC Receptacle Connector IEC-61754-4
Week (52Weeks/Year) : 1月2日=01

OPBD-155E1J1R
DELTA ELECTRONICS, INC.
7 Revision: S2
03/09/2007
www.deltaww.com
9. Regulatory Compliance
Feature Test Method Reference Performance
Human Body Model
(HBM)
MIL-STD-883E Method 3015.7
EIA-JESD22-A114
Electrostatic Discharge
(ESD) to the Electrical
Pins Machine Model (MM) EIA-JESD22-A115
Contact Discharge IEC/EN 61000-4-2Electrostatic Discharge
(ESD) to the Simplex
Receptacle Air Discharge IEC/EN 61000-4-2
Radio Frequency
Electromagnetic Field
Immunity
IEC/EN 61000-4-3
Electromagnetic
Interference (EMI)
FCC Part 15 Class B
EN 55022 Class B
(CISPR 22A)
(1) Satisfied with
electrical
characteristics of
product spec.
(2) No physical damage
Laser Eye Safety
FDA/CDRH
TUV
FDA 21CFR 1040.10, 1040.11
IEC/EN 60825-1
IEC/EN 60825-2
CDRH File # 0420993
TUV Certificate #
R50032471
Component Recognition
TUV
UL/CSA
IEC/EN 60950
UL 60950
UL File # E239394
Appendix B. Document Revision
Version No. Date Description
S0 2006-07-20 Preliminary datasheet
S1 2006-09-12 Add barcode on product label
S2 2007-03-09
Change the module height from 9.7±0.3mm to 10.8±0.3mm