Delta DOP-107EG User manual

DOP-107EG High color ‧ Wide screen ‧
User-friendly
Delta Electronics Inc,
No.18, Xinglong Rd., Taoyuan City
33068, Taiwan
Instruction Sheet
(1) General precautions
Thank you for purchasing this product. This instruction sheet provides information about the DOP-100
series HMI. Before using this product, please read through this instruction sheet carefully to ensure the
correct use of the product. Please keep this sheet handy for quick reference whenever needed. Before
finishing reading this sheet, please follow the instructions below:
 Install the product in an indoor location, which is free of vapor, corrosive and inflammable gas and
liquids.
 Please refer to the wiring diagram when connecting the wires.
 Ensure your HMI is correctly grounded. The grounding method must comply with the national
electrical standard (please refer to NFPA 70: National Electrical Code, 2005 Ed.).
 Do not disassemble the HMI or change the wiring when power is on.
 Do not touch the power supply when power is on, or it may cause electric shock.
 When the HMI displays a low power notification and requires a battery change, please contact
your local distributor or Delta Customer Service Center for the replacement. Do not change the
batteries by yourself.
 This product can be used with other industrial automation equipment. Please read through this
sheet carefully and install the product according to the instructions to avoid danger.
 Cleaning method: please use a dry cloth to clean the product.
 This product must be used at an altitude below 2,000 m.
 If the equipment is used in a manner not specified by the manufacturer, the protection provided by
the equipment may be impaired.
 For repair and maintenance, please contact Delta Electronics, Inc. Address: No.18, Xinglong Rd.,
Taoyuan City, Taiwan. TEL: [phone].
If you have any inquiry during operation, please contact our local distributors or Delta sales
representatives. The content of this instruction sheet may be revised without prior notice. Please consult
our distributors or download the latest version at Delta’s website (http://www.delta.com.tw/ia).
(2) Communication port pin assignment
DOP-107EG COM1 port
COM Port Pin MODE1
RS-232
1 -
2 RXD
3 TXD
4 -
5 GND
6 -
7 RTS
8 CTS
9 -
DOP-107EG COM2 port
COM Port Pin
MODE1 MODE2 MODE3
COM2 COM3 COM2 COM3 COM2 COM3
RS-232 RS-485 RS-485 RS-485 RS-232 RS-422
1 - - D+ - - TXD+
2 RXD - - - RXD -
3 TXD - - - TXD -
4 - D+ - D+ - RXD+
5 GND GND GND
6 - - D- - - TXD-
7 RTS - - - RTS -
8 CTS - - - CTS -
9 - D- - D- - RXD-
Note: mark “-” means connection is not required.
(3) Description of each part
DOP-107EG (front view)
AOperation / display area
DOP-107EG (rear view)
A USB Host B USB Slave
C Power input terminal
(24 AWG wire min.) D COM2 / COM3
E COM1 F Network Port（LAN）
(4) Mounting dimensions
DOP-107EG
Unit: mm (inch)
Operation temperature: 0oC to 50oC (32oF to 122oF)
Storage temperature: -20oC to +60oC (-4oF to 140oF)
(5) Installation and wiring
Precautions:
 Incorrect installation may result in malfunction.
 To ensure the HMI is well ventilated, make sure there is sufficient space between the HMI and the
adjacent objects or walls.
 This product should be used on a case / platform which conforms to enclosure Type 4X standard (for
indoor use only).
 The maximum panel thickness for mounting must be no greater than 5 mm.
Installation steps:
Step 1:
Put the waterproof gasket into the HMI and
then insert the HMI into the panel cutout.
Step 2:
Place the fasteners into the slots and tighten
the screws until reaching the panel cutouts.
Step 3:
Tighten the screws with the torque less than
0.5 N-M / 0.7 N-M to avoid damage to the
plastic case.
DOP-107BG torque: 6.17 lb-inch (0.7N-M)
Step 4:
For heat dissipation, please keep a minimum
clearance of 60 mm on the rear of the HMI.
Wiring:
Type Wire gauge (AWG) Stripped length Tor que
Solid 24 - 12 7 - 8 mm 5 kg-cm (4.3 lb-in)
Stranded 24 - 12 7 - 8 mm 5 kg-cm (4.3 lb-in)
Please refer to the following diagram when wiring the power connector. The temperature
rating of the cable must be greater than 75oC (167oF).

(6) Hardware specifications
Model DOP-107EG
Display
Panel type 7" TFT LCD (65535 colors)
Resolution 800 x 600 pixels
Backlight LED backlight (half-life under room temperature 25oC > 20,000 hours) *1
Display range 141.00 x 105.75 mm
Brightness 450 cd/m² (Typ.)
CPU ARM Cortex-A8 (800 MHz)
Flash ROM 256 Mbytes
RAM 256 Mbytes
Touchscreen 4-wire resistive touchscreen > 10,000,000 operated
Buzzer Multi-tone frequency (2 K – 4 KHz) / 80 dB
Network interface 10/100 Mbps Auto sensing (with built-in isolated power circuit) *2
USB 1 USB slave Ver 2.0; 1 USB host Ver 2.0
SD SD * 1
Serial
communication
port
COM1 RS-232 (supporting flow control) *2
COM2 RS-232 (supporting flow control) / RS-485*2
COM3 RS-422 / RS-485*2
Auxiliary function key N/A
Calendar Built-in
Cooling method Natural cooling
Approvals CE / UL (please use shielding network cable and magnetic ring with the
filter of 300 ohm / 100 MHz)
Panel waterproof level IP65 / NEMA4
Operation voltage*2
DC +24 V (-15% to +15%) (please use an isolated power supply)
Supplied by Class 2 or SELV circuit (isolated from MAINS
by double insulation)
Leakage current 500 VAC for 1 minute (between DC24V terminal and FG terminal)
Power consumption*2 8.4 W (Max)*3
Backup battery 3V lithium battery CR2032 × 1
Backup battery life About 3 years or more at 25oC
(subject to operation temperature and condition)
Operation temperature 0oC to 50oC (32oF to 122oF)
Storage temperature -20oC to +60oC (-4oF to 140oF)
Operating environment 10% to 90% RH [0oC to 40oC], 10% to 55% RH [41oC to 50oC];
pollution degree: 2
Vibration resistance Conforms to IEC61131-2: continuous vibration 5 Hz - 8.3 Hz with amplitude
3.5 mm; 8.3 Hz - 150 Hz with amplitude 1G
Shock resistance Conforms to IEC60068-2-27: 11 ms, 15 G Peak,
in X, Y, Z directions each for 6 times
Dimension
(W) x (H) x (D) mm 184 x 144 x 50
Mounting dimension
(W) x (H) mm 172.4 x 132.4
Weight Approx. 800 g
Note:
1. The half-life of the back light is defined as the maximum luminance being reduced by 50% when the
maximum drive current is supplied to the HMI. The life of LED backlight shown here is estimated at the
room temperature of 25oC with ambient humidity.
2. The withstand voltage of the isolated power circuit is 1500 V peak for 1 minute.
3. The HMI power consumption is the power consumed when the HMI is not connecting with other
peripheral devices. To ensure normal operation of the HMI, the recommended capacity of the power
supply is 1.5 to 2 times of the specified power consumption.
4. Isolated power supply is recommended.
5. For DOPSoft programming software for DOP-100 series and the user manual, you can download them
at http://www.delta.com.tw/ia.
6. DOP-100 series can be used with other industrial automation equipment. Please read through this
sheet carefully and install the product according to the instructions to avoid danger.