Delta Modulon DPH series User manual

Delta UPS - Modulon Family
The power behind competitiveness
www.deltapowersolutions.com
DPH Series, Three Phase
20-80 kVA/ 20-120 kVA
User Manual

II
Modulon DPH Series
SAVE THIS MANUAL
This manual contains important instructions and warnings that you should follow
during the installation, operation, storage and maintenance of this product. Failure
to heed these instructions and warnings will void the warranty.
Copyright © 2020 by Delta Electronics Inc. All Rights Reserved. All rights of this User Manual
(“Manual”), including but not limited to the contents, information, and figures are solely owned
and reserved by Delta Electronics Inc. (“Delta”). The Manual can only be applied to the operation
or the use of this product. Any disposition, duplication, dissemination, reproduction, modification,
translation, extraction, or usage of this Manual in whole or in part is prohibited without the prior
written permission of Delta. Given that Delta will continuously improve and develop the product,
changes may be made to the information in this Manual at any time without obligation to notify
DQ\SHUVRQRIVXFKUHYLVLRQRUFKDQJHV'HOWDZLOOPDNHDOOSRVVLEOHHႇRUWVWRVHFXUHWKHDFFXUDF\
and the integrity of this Manual. Delta disclaims any kinds or forms of warranty, guarantee,
or undertaking, either expressly or implicitly, including but not limited to the completeness,
IDXOWOHVVQHVVDFFXUDF\QRQLQIULQJHPHQWPHUFKDQWDELOLW\RU¿WQHVVIRUDSDUWLFXODUSXUSRVHRIWKH
Manual.

Table of Contents
III
Table of Contents
1. Important Safety Instructions---------------------------------------------- 1-1
1.1 Installation Warnings---------------------------------------------------------------------- 1-2
1.2 Connection Warnings--------------------------------------------------------------------- 1-2
1.3 Usage Warnings --------------------------------------------------------------------------- 1-4
1.4 Storage Warnings ------------------------------------------------------------------------- 1-5
1.5 Standard Compliance -------------------------------------------------------------------- 1-6
2. Introduction ---------------------------------------------------------------------- 2-1
2.1 General Overview ------------------------------------------------------------------------- 2-2
2.2 Package Inspection----------------------------------------------------------------------- 2-2
2.3 Functions & Features--------------------------------------------------------------------- 2-3
2.4 Exterior and Dimensions----------------------------------------------------------------- 2-5
2.5 Front View----------------------------------------------------------------------------------- 2-6
2.6 Internal View ------------------------------------------------------------------------------- 2-7
2.7 Rear View ----------------------------------------------------------------------------------2-11
2.8 Tri-color LED Indicator & Buzzer -----------------------------------------------------2-12
3. Operation Modes --------------------------------------------------------------- 3-1
3.1 Single Input --------------------------------------------------------------------------------- 3-2
3.1.1 On-Line Mode_ Single Input_ Single Unit -------------------------------- 3-2
3.1.2 Battery Mode_ Single Input_ Single Unit---------------------------------- 3-3
3.1.3 Bypass Mode_ Single Input_ Single Unit --------------------------------- 3-4
3.1.4 Manual Bypass Mode_ Single Input_ Single Unit----------------------- 3-4
3.1.5 ECO Mode_ Single Input_ Single Unit------------------------------------- 3-6
3.1.6 Frequency Conversion Mode_ Single Input_ Single Unit------------- 3-6
3.1.7 Green Mode_ Single Input_ Single Unit----------------------------------- 3-7
3.1.8 Energy Recycle Mode_ Single Input_ Single Unit---------------------- 3-8
3.1.9 On-Line Mode_ Single Input_ Parallel Units ----------------------------- 3-9
3.1.10 Battery Mode_ Single Input_ Parallel Units -----------------------------3-10
3.1.11 Bypass Mode_ Single Input_ Parallel Units-----------------------------3-11
3.1.12 Manual Bypass Mode_ Single Input_ Parallel Units ------------------3-12
3.1.13 ECO Mode_ Single Input_ Parallel Units --------------------------------3-14
3.1.14 Green Mode_ Single Input_ Parallel Units-------------------------------3-15
3.2 Dual Input-----------------------------------------------------------------------------------3-16
3.2.1 On-Line Mode_ Dual Input_ Single Unit----------------------------------3-16
3.2.2 Battery Mode_ Dual Input_ Single Unit-----------------------------------3-16
3.2.3 Bypass Mode_ Dual Input_ Single Unit ----------------------------------3-17

IV
Modulon DPH Series
3.2.4 Manual Bypass Mode_ Dual Input_ Single Unit------------------------3-18
3.2.5 ECO Mode_ Dual Input_ Single Unit--------------------------------------3-19
3.2.6 Frequency Conversion Mode_ Dual Input_ Single Unit--------------3-20
3.2.7 Green Mode_ Dual Input_ Single Unit------------------------------------3-21
3.2.8 On-Line Mode_ Dual Input_ Parallel Units ------------------------------3-22
3.2.9 Battery Mode_ Dual Input_ Parallel Units--------------------------------3-23
3.2.10 Bypass Mode_ Dual Input_ Parallel Units -------------------------------3-24
3.2.11 Manual Bypass Mode_ Dual Input_ Parallel Units---------------------3-25
3.2.12 ECO Mode_ Dual Input_ Parallel Units-----------------------------------3-27
3.2.13 Green Mode_ Dual Input_ Parallel Units---------------------------------3-28
3.3 Hot Standby Redundancy (Only For Dual Input & At Least Two UPSs)----3-29
3.4 Common Battery (Only for Parallel UPSs connecting to the Same
External Battery Cabinet(s))-----------------------------------------------------------3-30
4. Communication Interfaces-------------------------------------------------- 4-1
4.1 Communication Interfaces on the Front of the UPS with Front Door Open 4-2
4.1.1 Display Port----------------------------------------------------------------------- 4-4
4.1.2 REPO Dry Contacts------------------------------------------------------------ 4-4
4.1.3 External Battery Temperature Dry Contacts------------------------------ 4-5
4.1.4 External Switch/ Breaker Status Dry Contacts -------------------------- 4-6
4.1.5 Output Dry Contacts------------------------------------------------------------ 4-6
4.1.6 Input Dry Contacts-------------------------------------------------------------- 4-9
4.1.7 Parallel Communication Card-----------------------------------------------4-10
4.1.8 Parallel Ports--------------------------------------------------------------------4-11
4.1.9 SMART Slot ---------------------------------------------------------------------4-12
4.1.10 USB Port & RS-232 Port-----------------------------------------------------4-12
4.1.11 Auxiliary Power Cards --------------------------------------------------------4-13
4.1.12 Battery Start Buttons----------------------------------------------------------4-13
4.1.13 Routing for REPO Port, Dry Contacts, Parallel Ports, USB Port
& RS-232 Port------------------------------------------------------------------4-14
4.2 Communication Interfaces at the Rear of the Touch Panel--------------------4-17
5. Installation and Wiring ------------------------------------------------------- 5-1
5.1 Before Installation and Wiring---------------------------------------------------------- 5-2
5.2 Installation Environment ----------------------------------------------------------------- 5-2
5.3 UPS Transportation ---------------------------------------------------------------------- 5-4
5.4 Fixing the UPS ----------------------------------------------------------------------------- 5-5
5.5 Wiring----------------------------------------------------------------------------------------- 5-7
5.5.1 Pre-wiring Warnings------------------------------------------------------------ 5-7
 6LQJOH,QSXW'XDO,QSXW0RGL¿FDWLRQ--------------------------------------5-10

Table of Contents
V
5.5.3 Single Unit Wiring--------------------------------------------------------------5-12
5.5.4 Parallel Unit Wiring ------------------------------------------------------------5-18
5.6 External Battery Cabinet Connection Warnings ----------------------------------5-22
5.7 STS Module--------------------------------------------------------------------------------5-29
5.7.1 STS Module Installation------------------------------------------------------5-30
5.7.2 STS Module Removal --------------------------------------------------------5-32
5.7.3 STS Module’s LED Indicator------------------------------------------------5-34
5.8 Power Module (Optional)---------------------------------------------------------------5-35
5.8.1 Power Module Installation ---------------------------------------------------5-36
5.8.2 Power Module Removal------------------------------------------------------5-39
5.8.3 Power Module’s LED Indicator ---------------------------------------------5-41
6. UPS Operation------------------------------------------------------------------- 6-1
 3UH6WDUWXS3UH7XUQRႇ:DUQLQJVIRU6LQJOH8QLWDQG3DUDOOHO8QLWV ---- 6-2
6.2 Start-up Procedures ---------------------------------------------------------------------- 6-4
6.2.1 On-Line Mode Start-up Procedures---------------------------------------- 6-4
6.2.2 Battery Mode Start-up Procedures ----------------------------------------- 6-7
6.2.3 Bypass Mode Start-up Procedures----------------------------------------6-10
6.2.4 Manual Bypass Mode Start-up Procedures -----------------------------6-13
6.2.5 ECO Mode Start-up Procedures -------------------------------------------6-18
6.2.6 Frequency Conversion Mode Start-up Procedures--------------------6-22
6.2.7 Green Mode Start-up Procedures -----------------------------------------6-26
6.2.8 Energy Recycle Mode Start-up Procedures-----------------------------6-30
 7XUQRႇ3URFHGXUHV ---------------------------------------------------------------------6-33
 2Q/LQH0RGH7XUQRႇ3URFHGXUHV ---------------------------------------6-33
 %DWWHU\0RGH7XUQRႇ3URFHGXUHV-----------------------------------------6-35
 %\SDVV0RGH7XUQRႇ3URFHGXUHV ----------------------------------------6-37
 0DQXDO%\SDVV0RGH7XUQRႇ3URFHGXUHV------------------------------6-38
 (&20RGH7XUQRႇ3URFHGXUHV--------------------------------------------6-38
 )UHTXHQF\&RQYHUVLRQ0RGH7XUQRႇ3URFHGXUHV --------------------6-41
 *UHHQ0RGH7XUQRႇ3URFHGXUHV------------------------------------------6-44
 (QHUJ\5HF\FOH0RGH7XUQRႇ3URFHGXUHV -----------------------------6-46
7. LCD Display & Settings ------------------------------------------------------ 7-1
7.1 LCD Display Hierarchy------------------------------------------------------------------- 7-2
7.2 How to Turn on the LCD----------------------------------------------------------------- 7-3
7.3 ON/ OFF Button---------------------------------------------------------------------------- 7-5
7.4 Introduction of Touch Panel and Function Keys ----------------------------------- 7-7
7.5 Password Entry ---------------------------------------------------------------------------7-12
7.6 Main Screen -------------------------------------------------------------------------------7-12

VI
Modulon DPH Series
7.7 Main Menu ---------------------------------------------------------------------------------7-16
7.8 Power Flow, Summary, System Status & EMS -----------------------------------7-18
7.9 Check System Readings ---------------------------------------------------------------7-21
7.9.1 Main Input------------------------------------------------------------------------7-21
7.9.1.1 Check Kilowatt-Hour ----------------------------------------------------------7-22
7.9.2 Bypass Input --------------------------------------------------------------------7-33
7.9.3 Inverter Output------------------------------------------------------------------7-33
7.9.4 Power Module Summary-----------------------------------------------------7-34
7.9.5 UPS Output----------------------------------------------------------------------7-34
7.9.6 Battery Status-------------------------------------------------------------------7-35
7.9.7 EMS -------------------------------------------------------------------------------7-36
7.9.7.1 Connecting the optional EMS 1000 (EnviroProbe)--------------------7-40
7.9.8 BMS -------------------------------------------------------------------------------7-40
7.10 UPS Settings ------------------------------------------------------------------------------7-42
7.10.1 Bypass Setting------------------------------------------------------------------7-42
7.10.2 Mode Setting--------------------------------------------------------------------7-43
7.10.3 Output Setting-------------------------------------------------------------------7-44
7.10.4 Battery & Charging Setting --------------------------------------------------7-45
7.10.5 Parallel Setting------------------------------------------------------------------7-48
7.10.6 Dry Contact Setting -----------------------------------------------------------7-49
7.10.7 General Setting-----------------------------------------------------------------7-51
7.10.8 IP Setting-------------------------------------------------------------------------7-54
7.10.9 Control----------------------------------------------------------------------------7-55
7.10.10EMS Setting---------------------------------------------------------------------7-56
7.10.11 BMS Setting---------------------------------------------------------------------7-58
7.11 System Maintenance --------------------------------------------------------------------7-60
7.11.1 Alarm Warning------------------------------------------------------------------7-60
7.11.2 Historical Event-----------------------------------------------------------------7-60
7.11.3 Statistics--------------------------------------------------------------------------7-62
7.11.4 Test --------------------------------------------------------------------------------7-62
7.11.5 Clear-------------------------------------------------------------------------------7-63
7.11.6 Advanced Diagnosis ----------------------------------------------------------7-64
7.11.7 Version & S/N-------------------------------------------------------------------7-65
8. Optional Accessories--------------------------------------------------------- 8-1
9. Maintenance---------------------------------------------------------------------- 9-1
$SSHQGL[7HFKQLFDO6SHFL¿FDWLRQV--------------------------------------- A1-1
Appendix 2 : Warranty------------------------------------------------------------- A2-1

1-1
1Important Safety Instructions
1
Important Safety
Instructions
1.1 Installation Warnings
1.2 Connection Warnings
1.3 Usage Warnings
1.4 Storage Warnings
1.5 Standard Compliance

1-2
Modulon DPH Series
1.1 Installation Warnings
yThis is a three-phase four-wire on-line uninterruptible power supply (hereafter referred
to as 'UPS'). It can be used for commercial and industrial applications.
yInstall the UPS in a well-ventilated indoor area, away from excess moisture, heat, dust,
ÀDPPDEOHJDVRUH[SORVLYHV
yLeave adequate space around all sides of the UPS for proper ventilation and mainte-
nance. Please refer to 5.2 Installation Environment.
yOnly authorized Delta engineers or service personnel can perform installation and
maintenance. If you want to install the UPS by yourself, please install it under the su-
pervision of authorized Delta engineers or service personnel
yFollow the IEC 60364-4-42 standard to install the UPS.
1.2 Connection Warnings
yBefore applying electrical power to the UPS, make sure the UPS is grounded to avoid a
possible risk of current leakage.
yYou can parallel at maximum eight UPS units.
yThe UPS must be connected with an external battery cabinet (user-supplied, handled
DQGFRQ¿JXUHGE\'HOWDVHUYLFHSHUVRQQHO3OHDVHUHIHUWR5.6 External Battery Cabi-
net Connection Warnings for relevant information.
yThe installation of protective devices is highly recommended when the UPS is connect-
ed to power sources and critical loads.
yThe protective devices connected to the UPS must be installed near the UPS and eas-
ily accessible for operation.
yProtective Devices:
1. For single input, please install (1) a protective device between the main AC source
and the UPS and (2) a protective device between the connected critical loads and
the UPS.
2. For dual input, please install (1) a protective device between the main AC source
and the UPS, (2) a protective device between the bypass source and the UPS, and (3)
a protective device between the connected critical loads and the UPS.

1-3
1Important Safety Instructions
3. Each protective device could be (1) a breaker, (2) a switch connected in series with
fuses, or (3) a switch*1. For the protective device’s rating current, please refer to the
table below.
20kVA 40kVA 60kVA 80kVA 100kVA 120kVA
40A 75A 125A 160A 200A 225A
NOTE:
*1Only applicable when the UPS has the corresponding built-in fuses, and
WKHFRQ¿JXUDWLRQVRIWKH836¶VEXLOWLQIXVHVPXVWPHHWWKHSURWHFWLYH
device’s requirement No.7 stated in Page 1-3.
4. Each protective device should have the functions of over current protection, short
circuit protection, insulating protection and shunt trip feature. Please refer to the
WDEOHEHORZIRUWKH836¶VFXWRႇFXUUHQW,FF
20kVA 40kVA 60kVA 80kVA 100kVA 120kVA
6kA 6kA 10kA 10kA 10kA 10kA
5. When selecting the protective devices, please take each power cable’s current
capacity and the system’s overload capacity (please refer to Appendix 1: Technical
Specifications) into consideration. Besides, the short-circuit capacity of the
upstream protective devices must be equal to or larger than the capacity of the
UPS’s input protective devices.
6. When the UPS has abnormalities and input short current reaches 8kA, the UPS’s
LQWHUQDOEUHDNHUVQHHGPVaPVWREHWULSSHGRႇ7KXVWKHXSVWUHDPSURWHFWLYH
devices’ reaction time should be more than 10ms to let the UPS’s internal breakers
block breakdown and let the UPS transfer to bypass mode.
7. If the UPS is supplied by a power source whose neutral is grounded, the backfeed
protective device installed as UPS input protection must be a 3-pole type. If the
UPS is supplied by a power source whose neutral is not grounded, the backfeed
protective device installed as UPS input protection must be a 4-pole type.
8. The recommended electrical rating of the backfeed protective device is as follows.
20kVA 40kVA 60kVA 80kVA 100kVA 120kVA
690V/ 40A 690V/ 75A 690V/ 125A 690V/ 160A 690V/ 200A 690V/ 225A

1-4
Modulon DPH Series
1.3 Usage Warnings
yBefore installation, wiring and working on the UPS’s internal circuits, please completely
FXWRႇDOOSRZHUVXSSO\LQJWRWKH836LQFOXGLQJWKHLQSXWSRZHUDQGEDWWHU\SRZHU
yThe UPS is specifically designed for information technology equipment and used to
power computers, servers, and associated peripheral devices. If you want to connect
any capacitive loads or non-linear loads (that have serious surge current) to the UPS,
it needs to be de-rated according to on-site applications. For such special applications,
please contact Delta service personnel for the accurate UPS sizing. The UPS is not
suitable for connecting with any asymmetrical loads.
yThe external slits and openings in the UPS are provided for ventilation. To ensure reli-
able operation of the UPS and to protect the UPS from overheating, these slits and
openings must not be blocked or covered. Do not insert any object into the slits and
openings that may hinder ventilation.
yBefore applying electrical power to the UPS, you must allow the UPS to adjust to room
temperature 20°C ~ 25°C (68°F ~ 77°F) for at least one hour to avoid moisture con-
densing inside the UPS.
yDo not put beverages on the UPS, external battery cabinet(s) or any other accessory
associated with the UPS.
yDo not open or remove the covers or panels of the UPS to avoid high voltage electric
shock. Only authorized Delta engineers or service personnel can do so for installation
or maintenance. If you want to open or remove the covers or panels, do it only under
the supervision of authorized Delta engineers or service personnel.
yIt is strictly forbidden to connect the UPS to any regenerative loads.
yThe risk of dangerous high voltage is possible when batteries are still connected to the
UPS even though the UPS is disconnected from the power sources. Before mainte-
QDQFHRIWKH836WXUQRႇHDFKH[WHUQDOEDWWHU\FDELQHW¶VFLUFXLWEUHDNHUWRFRPSOHWHO\
FXWRႇWKHEDWWHU\SRZHUIURPWKH836
y'RQRWGLVSRVHRIWKHEDWWHU\RUEDWWHULHVLQD¿UH7KHEDWWHULHVPD\H[SORGH
yDo not open or damage the battery or batteries. The released electrolyte is harmful to
the skin and eyes and may be toxic.
yThe UPS is electronic equipment that runs 24 hours continuously. To ensure its normal
lifetime, regular maintenance of the UPS and batteries is of vital importance and neces-
sary.

1-5
1Important Safety Instructions
ySome components like batteries, power capacitors, and fans will become worn-out due
to long-term usage, and this will increase the risk of UPS failure. To replace and main-
tain the components, please contact Delta service personnel.
yA battery can present a risk of electric shock and high short-circuit current. The follow-
ing precautions should be observed before replacement of batteries:
1. Remove watches, rings, or other metal objects.
2. Use tools with insulated handles.
3. Wear insulating gloves and boots.
4. Do not lay tools or metal parts on the top of batteries.
5. Disconnect the charging source prior to connecting or disconnecting the batteries’
terminals.
yYou must contact Delta customer service if either of the following events occurs:
1. Liquid is poured or splashed on the UPS.
2. The UPS is deformed.
3. Any conductive powders or metals enter into the UPS.
4. The UPS does not run normally after you carefully followed the instructions in this
User Manual.
NOTE:
If you use the UPS in an area that generates or incurs dust, you should
LQVWDOOGXVW¿OWHUVLQWKH836WRHQVXUHQRUPDOSURGXFWOLIHDQGIXQFWLRQ
1.4 Storage Warnings
yUse the original packing material to pack the UPS to prevent any possible damage from
rodents.
yIf the UPS needs to be stored prior to installation, it should be placed in a dry indoor
area. The allowable storage temperature is below 40°C (104°F) and relative humidity is
below 95%.

1-6
Modulon DPH Series
1.5 Standard Compliance
yEN 62040-1
yEN 61000-6-4
yEN 62040-2 Category C3
yEN 61000-4-2
yEN 61000-4-3
yEN 61000-4-4
yEN 61000-4-5
yEN 61000-4-6
yEN 61000-4-8
yEN 61000-2-2

2-1
2Introduction
2
Introduction
2.1 General Overview
2.2 Package Inspection
2.3 Functions & Features
2.4 Exterior and Dimensions
2.5 Front View
2.6 Internal View
2.7 Rear View
2.8 Tri-color LED Indicator
& Buzzer

2-2
Modulon DPH Series
2.1 General Overview
The DPH series UPS, a three-phase four-wire online uninterruptible power supply (hereafter
referred to as ‘UPS’), is a dedicated design for data centers, factory facilities and large scale
power systems. The unit not only adopts advanced IGBT technology to provide high quality,
low noise, pure and uninterruptible output power to the connected loads, but also applies
the latest design of DSP digital control technology and highest quality components.
The UPS supports high efficient operation modes and its modular and hot-swappable
design makes maintenance easy and quick. You can add power modules (optional)
according to on-site applications to expand overall system capacity, which realizes a highly
cost-effective solution to your power requirements and produces greater electric power
HႈFLHQF\DWOHVVFRVW
7KHXQLWSURYLGHVGLYHUVL¿HGFRPPXQLFDWLRQLQWHUIDFHVDQGFRPPXQLFDWLRQSURWRFROV6103
and MODBUS) for you to facilitate remote control and management. You can parallel at
maximum eight UPS units to increase the system capacity and redundancy and enhance
the unit’s availability and reliability.
2.2 Package Inspection
yExternal
During UPS transportation, some unpredictable situations might occur. It is recom-
mended that you inspect the UPS exterior packaging. If you notice any damage, please
immediately contact the dealer from whom you purchased the unit.
yInternal
1. Check the rating label attached to the UPS and make sure the device No. and
capacity match what you ordered.
2. Examine if any parts are loose or damaged.
3. The UPS package contains the following items. Please check if any items are
missing.
12
5
4
3
7 8
9
6
10 11 12
× 18
× 2 × 2

2-3
2Introduction
No. Item Q'ty
1UPS 1 PC
2User Manual 1 PC
3RS-232 Cable (1.8 meters (5.91 ft)) 1 PC
4Parallel Cable (3 meters (9.84 ft)) 1 PC
5Test Report 1 PC
6Key 1 PC (two copies
placed inside the
UPS cabinet)
7M10 Screw (used for input/ output/ battery/
grounding wiring) 18 PCS
8USB Cable 1 PC
94-Pin Dry Contact Terminal Block
(used for REPO dry contacts; please refer to
Figure 4-3)1 PC
10
6-Pin Dry Contact Terminal Block
(used for MODBUS and BMS ports located at the
rear of the touch panel; please refer to Figure 4-25)1 PC
11
8-Pin Dry Contact Terminal Block
(used for (1) external battery temperature dry
contacts and (2) external switch/ breaker status dry
contacts; please refer to Figure 4-3)
2 PCS
12
10-Pin Dry Contact Terminal Block (used for input
and output dry contacts; please refer to Figure 4-3)2 PCS
4. If there is any damage or anything missing, please immediately contact the dealer
from whom you purchased the unit.
5. If the UPS needs to be returned, carefully repack the UPS and all of the accessories
using the original packing material that came with the unit.
2.3 Functions & Features
yHot swappable STS module, communication interfaces and power modules (optional)
realize on-line maintenance, reduce the MTTR (Mean Time to Repair) and expand sys-
WHPFDSDFLW\ÀH[LEO\aN9$aN9$
y,QSXWSRZHUIDFWRU!DQGLQSXW7+'LVDYHRQLQVWDOODWLRQFRVWDQGGLPLQLVK
power contamination.

2-4
Modulon DPH Series
yOutput power factor=1.
y(ႈFLHQF\!VDYHVRQRSHUDWLRQFRVW
yAutomatic input frequency detection enables operation at 40Hz ~70Hz.
yAutomatic restart
1. The UPS will restart in normal mode automatically right after the AC line resumes
following a low battery shutdown.
2. The UPS returns automatically to normal mode from bypass mode after an overload
condition is cleared.
yAutomatically detects whether bypass voltage is out of rating voltage (default: voltage
±15% & frequency ±3Hz). If yes, the UPS will stop supplying power to the critical loads
to protect your electronic equipment.
ySupports ECO mode: when input voltage and frequency are within the range of rating
voltage ±10% and rating frequency ±3Hz, the UPS will transfer to bypass mode; other-
ZLVHWKH836ZLOOWUDQVIHUWRQRUPDOPRGHWRUHDFKKLJKHUHႈFLHQF\
yBoth auxiliary power and control circuit adopt redundancy design, which doubly en-
hances UPS reliability.
yApplicable to top or bottom wiring.
yGenerator compatible.
y6XUJHSURWHFWLRQDQG(0,¿OWHUIXQFWLRQV
y5HPRWHHPHUJHQF\SRZHURႇ
ySingle input and dual input functions.
ySupports external switch/ breaker status detection.
yWide AC input voltage range (full load: 176Vac~276Vac; < 70% load: 132Vac~176Vac)
reduces frequent transfer from normal mode to battery mode to save battery consump-
tion and prolong battery life.
yBattery start-up function even when there is no AC input.
yAC start-up function even when the UPS is not connected to the batteries.
WARNING:
Please note that when the UPS is not connected to the batteries, it will not
protect your equipment if the utility power is lost.

2-5
2Introduction
yConnects at maximum eight external battery cabinets to extend backup time.
ySets up schedulable battery test and battery replacement alarm.
yBattery temperature monitoring and compensation.
yOptional battery management system (BMS) allows measurement of every battery’s
voltage.
ySmart battery charger design allows auto-charging or manual charging to shorten
charging time.
y3URYLGHVGLYHUVL¿HGFRPPXQLFDWLRQLQWHUIDFHVDQGDVPDUWVORW3OHDVHUHIHUWR4. Com-
munication Interfaces.
yBuilt-in RS-232 port and USB port located on the communication interfaces allow moni-
toring and management of the UPS. For relevant location and information, please refer
to Figure 4-16.
yBuilt-in SNMP card and MODBUS card located at the rear of the touch panel provide
network communication and MODBUS communication respectively. Besides, the SNMP
card allows remote monitoring, management and event log download of the UPS. For
relevant location and information, please refer to Figure 4-25.
yBuilt-in USB ports ( ) located at the rear of the touch panel allow upgrade of the
UPS, touch panel, power modules, system control card and parallel communication
FDUG¶V¿UPZDUHDQGHYHQWORJGRZQORDG)RUUHOHYDQWORFDWLRQDQGLQIRUPDWLRQSOHDVH
refer to Figure 4-25.
yBuilt-in SRAM records at maximum 10000 event logs.
y10-inch graphic and color touch panel enables users to easily operate the UPS and un-
derstand the UPS status.
yFan speed auto adjustment prolongs fan life and reduces noise when the critical loads
decrease. Moreover, fan failure detection circuit is established.
yState-of-the-art microprocessor technology performs self-detection and monitors fan
speed in real time, which provides complete and detailed operating status of the UPS.
2.4 Exterior and Dimensions
7KH836KDVWZRGLႇHUHQWV\VWHPFDELQHWVaN9$DQGaN9$7KHLUH[WHULRU
and size are the same (see Figure 2-1 and Figure 2-2), but their power module slot’s
TXDQWLW\ORFDWLRQ676PRGXOH¶VVL]HDQGZHLJKWDUHGLႇHUHQWVHH2.6 Internal View).

2-6
Modulon DPH Series
1445mm
(56.89”)
850mm
(33.46”)
600mm
(23.62”)
(Figure 2-1: Exterior and Dimensions)
2.5 Front View
On the front of the UPS, there are a 10” color touch panel, a tri-color LED indicator, a door
switch, four casters and four leveling feet. Please see Figure 2-2.
10” Color Touch Panel
Door Switch
Tri-color LED Indictor
CastersLevelling Feet
Levelling Foot
(Figure 2-2: UPS Front View)

2-7
2Introduction
1. For information about the 10” color touch panel, please refer to 7. LCD Display &
Settings.
2. For information about the tri-color LED indicator, please refer to 2.8 Tri-color LED
Indicator & Buzzer.
3. The casters at the bottom of the UPS can be used to move over short distances, and
the leveling feet fix and stabilize the UPS on the ground. Please refer to 5.3 UPS
Transportation for relevant information.
4. Please refer to Figure 2-3 for how to open the UPS front door.
90°90°
Pull UpPull Up
(Figure 2-3: How to Open the UPS Front Door)
2.6 Internal View
WARNING:
Only authorized Delta engineers or service personnel can perform installation,
wiring, panel & cover removal, maintenance and operation. If you want to execute
any action mentioned above by yourself, the action must be under the supervision
of authorized Delta engineers or service personnel.
NOTE:
7KH836KDVWZRGLႇHUHQWV\VWHPFDELQHWVaN9$DQGaN9$7KHLU
exterior and size are the same (see Figure 2-1 and Figure 2-2), but their power
PRGXOHVORW¶VTXDQWLW\ORFDWLRQ676PRGXOH¶VVL]HDQGZHLJKWDUHGLႇHUHQWVHH
Figure 2-4 and information below).

2-8
Modulon DPH Series
After you open the UPS’s front door, you will see the internal mechanisms including
communication interfaces, four or six power module slots (varied according to different
cabinet systems), an STS module, four breakers (Input/ Bypass/ Manual Bypass/ Output)
and one wiring terminal cover. Please refer to Figure 2-4.
DISPLAY
REPO
NC NO
EXT.BATT
TEMP.
BT1 BT2
EXT.SWITCH
STATUS
S1 S2
S3 S4
BT3 BT4
O/PDRY
CONTACT
USB RS-232
P1 P2 P3
P4 P5 P6
I/PDRY
CONTACT
P1 P2
BATT.
START
BATT.
START
P3 P4 PARALLEL
DISPLAY
REPO
NC NO
EXT.BATT
TEMP.
BT1 BT2
EXT.SWITCH
STATUS
S1 S2
S3 S4
BT3 BT4
O/PDRY
CONTACT
USB RS-232
P1 P2 P3
P4 P5 P6
I/PDRY
CONTACT
P1 P2
BATT.
START
BATT.
START
P3 P4 PARALLEL
INPUT
BREAKER OUTPUT
BREAKER
BYPASS
BREAKER MANUAL BYPASS BREAKER
DISPLAY
EMS
/CONSOLE
RESET
GND B A GND B A
MODBUS BMS
DISPLAY
EMS
/CONSOLE
RESET
GND B A GND B A
MODBUS BMS
INPUT
BREAKER OUTPUT
BREAKER
BYPASS
BREAKER MANUAL BYPASS BREAKER
1Communication Interfaces
(20 ~ 80kVA UPS Internal View with Front Door Open))
(20 ~ 120kVA UPS Internal View with Front Door Open)
1Communication Interfaces
2
3
4Input, Bypass, Manual Bypass &
Output Breakers (from Left to Right)
STS Module
5Wiring Terminal Cover
Power Module Slot × 4
1. Only the Top Two Slots Have Covers.
2. The Bottom Two Slots Don’t Have Covers.
2
3
4Input, Bypass, Manual Bypass &
Output Breakers (from Left to Right)
STS Module
5Wiring Terminal Cover
Power Module Slot × 6
1. Only the Top Three Slots Have Covers.
2. The Bottom Three Slots Don’t Have Covers.
(Figure 2-4: UPS Internal View with front Door Open)