Denon DBT-1713UD User manual

START::|qzT7t3cIXfGvpSN6RPbAWw==|pZ4UN5KywSHs7MJPvo/7X45inRAIfAQbMnOz/mZRuhU=|RtRIz5LbaS+BXuKmvA5tJg==|::END
D&M Holdings Inc.
SERVICE MANUAL
e
e
MODEL JP E3 E2 E1 E1C EUT
DBT-1713UD
PPPP
UNIVERSAL AUDIO/VIDEO PLAYER
Ver. 8
• Some illustrations using in this service manual are slightly different from the actual set.
• Please use this service manual with referring to the operating instructions without fail.
• For purposes of improvement, specications and design are subject to change without notice.
Please refer to the
MODIFICATION NOTICE.

2
CONTENTS
SAFETY PRECAUTIONS..........................................................3
NOTE FOR SCHEMATIC DIAGRAM.........................................4
NOTE FOR PARTS LIST...........................................................4
WARNING AND LASER SAFETY INSTRUCTIONS.................5
INSTRUCTIONS FOR HANDLING
SEMI-CONDUCTORS AND OPTICAL UNIT.............................6
1. Ground for Human Body .......................................................6
2. Ground for Workbench ..........................................................6
TECHNICAL SPECIFICATIONS................................................7
DIMENSION...............................................................................7
CAUTIONS IN SERVICING .......................................................8
Initializing BD player..................................................................8
Service tools..............................................................................8
DISASSEMBLY..........................................................................9
1. FRONT PANELASSY .........................................................10
2. BD MECHA UNIT ASSY .....................................................11
3. MAIN PCB UNITASSY .......................................................12
4. POWER PCB UNITASSY ..................................................13
5. IR PCB UNITASSY ............................................................13
REMOVING DISCS.................................................................14
DIAGNOSTICS OF OPTICAL PICKUP...................................15
1. Iop checked Method............................................................16
2. To clear the accumulated laser on time...............................16
HOW TO REPLACE THE MAIN PCB & BD MECHA
OR BD MECHA........................................................................17
1. How to Replace the MAIN PCB & BD MECHA ..................17
2. How to Replace the BD MECHA.........................................17
HOW TO REPLACE THE MAIN PCB UNIT ASSY..................22
SERVICE MODE......................................................................24
1. Initial setting mode ..............................................................24
2. Firmware version check mode ............................................24
3. Tray lock mode....................................................................25
4. Remote lock mode ..............................................................25
5. All Lit / All Off mode for the FL tube.....................................25
6. Test mode ...........................................................................26
PROCEDURE FIRMWARE FOR UPGRADING THE VERSION
OF THE FIRMWARE ...............................................................31
1. Update from the Internet .....................................................31
TROUBLE SHOOTING............................................................32
1. Power (Power Board)..........................................................32
2. LED blinking ........................................................................33
3. Power board........................................................................33
4. DISPLAY (Display Board)....................................................34
5. HDMI...................................................................................35
6. Network...............................................................................35
7. USB.....................................................................................36
8. No Audio output...................................................................36
9. Disc playback error .............................................................37
BLOCK DIAGRAM...................................................................38
POWER BLOCK DIAGRAM....................................................39
PRINTED WIRING BOARDS...................................................40
MAIN ......................................................................................40
FRONT ...................................................................................41
IRA1G ....................................................................................43
SCHEMATIC DIAGRAMS (1/15) .............................................44
POWER...................................................................................44
DISPLAY_01 ...........................................................................45
DISPLAY_02 ...........................................................................46
IR ............................................................................................47
MAIN_01.................................................................................48
MAIN_02.................................................................................49
MAIN_03.................................................................................50
MAIN_04.................................................................................51
MAIN_05.................................................................................52
MAIN_06.................................................................................53
MAIN_07.................................................................................54
MAIN_08.................................................................................55
MAIN_09.................................................................................56
MAIN_10.................................................................................57
MAIN_11..................................................................................58
EXPLODED VIEW....................................................................59
PARTS LIST OF EXPLODED VIEW .......................................60
PACKING VIEW ......................................................................62
PARTS LIST OF PACKING VIEW ..........................................63
SEMICONDUCTORS...............................................................64
1. IC's ......................................................................................64
PARTS LIST OF PCB .............................................................76

3
SAFETY PRECAUTIONS
The following items should be checked for continued protection of the customer and the service technician.
LEAKAGE CURRENT CHECK
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the set is defective.
Be sure to test for leakage current with the AC plug in both polarities, in addition, when the set's power is in each state (on,
off and standby mode), if applicable.
CAUTION Please heed the following cautions and instructions during servicing and
inspection.
◎Heed the cautions!
Cautions which are delicate in particular for servicing
are labeled on the cabinets, the parts and the chassis,
etc. Be sure to heed these cautions and the cautions
described in the handling instructions.
◎Cautions concerning electric shock!
(1) An AC voltage is impressed on this set, so if
you touch internal metal parts when the set is
energized, you may get an electric shock. Avoid
getting an electric shock, by using an isolating
transformer and wearing gloves when servicing
while the set is energized, or by unplugging the
power cord when replacing parts, for example.
(2) There are high voltage parts inside. Handle with
extra care when the set is energized.
◎Caution concerning disassembly and
assembly!
Through great care is taken when parts were
manufactured from sheet metal, there may be burrs
on the edges of parts. The burrs could cause injury if
ngers are moved across them in some rare cases.
Wear gloves to protect your hands.
◎Use only designated parts!
The set's parts have specic safety properties (re
resistance, voltage resistance, etc.). Be sure to use
parts which have the same properties for replacement.
The burrs have the same properties. In particular, for
the important safety parts that are indicated by the z
mark on schematic diagrams and parts lists, be sure to
use the designated parts.
◎Be sure to mount parts and arrange the wires
as they were originally placed!
For safety seasons, some parts use tapes, tubes or
other insulating materials, and some parts are mounted
away from the surface of printed circuit boards.
Care is also taken with the positions of the wires by
arranging them and using clamps to keep them away
from heating and high voltage parts, so be sure to set
everything back as it was originally placed.
◎Make a safety check after servicing!
Check that all screws, parts and wires removed or
disconnected when servicing have been put back in
their original positions, check that no serviced parts
have deteriorate the area around. Then make an
insulation check on the external metal connectors and
between the blades of the power plug, and otherwise
check that safety is ensured.
(Insulation check procedure)
Unplug the power cord from the power outlet,
disconnect the antenna, plugs, etc., and on the power.
Using a 500V insulation resistance tester, check that
the insulation resistance value between the inplug and
the externally exposed metal parts (antenna terminal,
headphones terminal, input terminal, etc.) is 1MΩ or
greater. If it is less, the set must be inspected and
repaired.
Many of the electric and the structural parts used in
the set have special safety properties. In most cases
these properties are difcult to distinguish by sight, and
the use of replacement parts with higher ratings (rated
power and withstand voltage) does not necessarily
guarantee that safety performance will be preserved.
Parts with safety properties are indicated as shown
below on the wiring diagrams and the parts list in this
service manual. Be sure to replace them with the parts
which have the designated part number.
(1) Schematic diagrams.......Indicated by the z mark.
(2) Parts lists.......Indicated by the zmark.
The use of parts other than the
designated parts could cause electric
shocks, res or other dangerous
situations.
CAUTION Concerning important safety
parts

4
NOTE FOR SCHEMATIC DIAGRAM
WARNING:
Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
CAUTION:
Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the
leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
WARNING:
DO NOT return the unit to the customer until the problem is located and corrected.
NOTICE:
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM
ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENTARE MEASURED AT NO
SIGNAL INPUT CONDITION. CIRCUITAND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
Parts indicated by "nsp" on this table cannot be supplied.
When ordering a part, make a clear distinction between "1" and "I" (i) to avoid mis-supplying.
A part ordered without specifying its part number can not be supplied.
General-purpose Carbon Chip Resistors are not included are not included in the P.W.Board parts list.
(Refer to the Schematic Diagram for those parts.)
Parts indicated by the zmark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
Part indicated by "★" mark is not illustrated in the exploded view.
WARNING:
1.
2.
3.
4.
5.
6.
NOTE FOR PARTS LIST
●Resistors
Value Tolerance Description
1Ω 5% 1
10Ω 5% 10
4.7KΩ 5% 4.7K
10KΩ 5% 10K
12.1KΩ 1% 12.1K/1%
●Electrolytic capacitor
Value Voltage Description
47μF 16V 47uF/16V
●Ceramic capacitor
Value Voltage Gread Description
0.1μF 25V Y5V 0.1uF/25V/Y5V
0.1μF 50V X7R 0.1uF/50V/X7R
●NC (not implemented)
Description Exsample
NC NC
*/NC 100uF/10V/NC
NC/* NC/0.1uF/25V/Y5V

5
FATTENTION DWARNUNG
WAARSCHUWING
AVVERTIMENTO
WARNING
Safety regulations require that the set be restored to its original condition
and that parts which are identical with those specified be used.
Veiligheidsbepalingen vereisen, dat het apparaat in zijn oorspronkelijke
toestand wordt terug gebracht en dat onderdelen, identiek aan de
gespecifieerde worden toegepast.
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten.
Der Originalzustand des Gerats darf nicht verandert werden.
Fur Reparaturen sind Original-Ersatzteile zu verwenden.
Le norme di sicurezza esigono che l’apparecchio venga rimesso nelle
condizioni originali e che siano utilizzati pezzi di ricambiago idetici a quelli
specificati.
Les normes de sécurité exigent que l’appareil soit remis a l’état d’origine et
que soient utilisées les pièces de rechange identiques à celles spécifiées.
“Pour votre sécurité, ces documents
doivent être utilisés par des
spécialistes agrées, seuls habilités à
réparer votre appareil en panne.”
GB NL
I
D
I
F
GB
NL
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are connected
with the same potential as the mass of the set via a
wrist wrap with resistance.
Keep components and tools also at this potential.
Tous les IC et beaucoup d’autres semiconducteurs
sont sensibles aux décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est prise
a leur manipulation.
Lors de réparations, s’assurer de bien être relié au
même potentiel que la masse de l’appareil et enfiler
le bracelet serti d’une résistance de sécurité.
Veiller a ce que les composants ainsi que les outils
que l’on utilise soient également a ce potentiel.
Alle IC und viele andere Halbleiter sind
empfindlich gegen elektrostatische
Entladungen (ESD).
Unsorgfältige Behandlung bei der Reparatur
kann die Lebensdauer drastisch vermindern.
Sorgen sie dafür, das Sie im Reparaturfall
dem Massepotential des Gerätes verbunden
sind.
Halten Sie Bauteile und Hilfsmittel ebenfalls
über ein Pulsarmband mit Widerstand mit auf
diesem Potential.
Alle IC’s en vele andere halfgeleiders zijn gevoelig
voor elektrostatische ontladingen (ESD).
Onzorgvuldig behandelen tijdens reparatie kan de
levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een polsband
met weerstand verbonden bent met apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
Tutti IC e parecchi semi-conduttori sono sensibili
alle scariche statiche (ESD).
La loro longevita potrebbe essere fortemente ridatta
in caso di non osservazione della piu grande
cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto a
resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo potenziale.
LASER SAFETY
CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPENAVOID EXPOSURE TO BEAM
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDS
Æ TTELSE FOR STRÅLING
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL Å PNES UNNGÅ EKSPONERING FOR STRÅLEN
VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNADEL ÄR ÖPPNAD BETRAKTAEJ STRÅLEN
VARO! AVATT AESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN
VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENNABDECKUNG GEÖFFNET NICHT DEM STRAHLAUSSETSEN
DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM
ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
AVOID DIRECT EXPOSURE TO BEAM
WARNING
The use of optical instruments with this product will
increase eye hazard.
Repair handling should take place as much as possible with
a disc loaded inside the player
WARNING LOCATION: INSIDE ON LASER COVERSHIELD
This unit employs a laser. Only a qualified service person should
remove the cover or attempt to service this device, due to
possible eye injury.
100301DM
CAUTION-CLASS 2 VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT STARE INTO THE BEAM.
VAROITUS-LUOKAN 2 NÄKYVÄÄ JA NÄKYMÄTÖNTÄ
LASERSÄTEILYÄ AVATUNA. ÄLÄ TUIJOTA SÄTEESEEN.
VARNING-KLASS 2 SYNLIG OCH OSYNLIG
LASERSTÅLNING VID ÖPPNING. STIRRA EJ NI I STRÅLEN.
ADVARSEL-KLASSE 2 SYNLIG OG USYNLIG LASERSTRÅLING
VED ÅBNING. SE IKKE IND I STRÅLEN.
WARNING AND LASER SAFETY INSTRUCTIONS

6
INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT
Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential difference
caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the
semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band,
be careful to avoid contacting semi-conductors with your clothing
<Incorrect>
CBA
Grounding Band
Conductive Sheet or
Copper Plate
1MΩ
1MΩ
<Correct>
CBA

7
TECHNICAL SPECIFICATIONS
nPerformance
Signal format : NTSC, PAL
(1) BD-Video disc :
12 cm, 1 side, 1 layer; 12 cm, 1 side, 2 layers
(2) DVD-Video / DVD-Audio disc :
12 cm, 1 side, 1 layer; 12 cm, 1 side, 2 layers /
12 cm, 2 sides, 2 layers (1 side, 1 layer)
8 cm, 1 side, 1 layer; 8 cm, 1 side, 2 layers /
8 cm, 2 sides, 2 layers (1 side, 1 layer)
(3) Super Audio CD :
12 cm, 1 layer / 12 cm, 2 layer / 12 cm, Hybrid
(4) Compact Disc (CD-DA) :
12 cm, / 8 cm, disc
(5) Memory device :
USB memory device (USB 2.0)
HDMI output :
Output terminal : 19-pin HDMI terminals, 1 set
HDMI ver. 1.4
(Deep Colour, Dolby Digital Plus, Dolby TrueHD, DTS-HD, 3D Ready)
Analog audio output :
Output level : 2 Vrms (10 kΩ)
2 channels output terminal : Pin-jack, 1 set
Audio output characteristics :
(1) Frequency response
qBD (Linear PCM) : 2Hz ~ 22kHz (48kHz sampling)
: 2Hz ~ 44kHz (96kHz sampling)
: 2Hz ~ 88kHz (192kHz sampling)
wDVD (Linear PCM) : 2Hz ~ 22kHz (48kHz sampling)
: 2Hz ~ 44kHz (96kHz sampling)
: 2Hz ~ 88kHz (192kHz sampling)
eSuper Audio CD : 2Hz ~ 40kHz
rCD : 2Hz ~ 20kHz
(2) S/N ratio : 115dB
(3) Total harmonic distortion : 1kHz 0.0025%(BD)
(4) Dynamic range : 100dB(BD)
nGeneral
Power supply : AC 120 V, 60 Hz (for E3)
AC 100-240 V, 50-60 Hz (for E2,E1)
AC 220 V, 50 Hz (for E1C)
Power consumption :20W (for E3)
20W (for E2,E1C)
Power Saving : When in Power Saving Standby : 0.3 W
When in Normal Standby : 0.5 W
Maximum external dimensions : 434 (W) x 108 (H) x 295 (D) mm
Weight : 4.9kg
DIMENSION
Dimension DBT-1713UD
192
49.5
2
288 5
295
340
434
90.517.5
108
195
43.5
23
17.5
128
140

8
CAUTIONS IN SERVICING
Initializing BD player
BD player initialization should be performed when the μcom, peripheral parts of μcom, and MAIN PCB. were replaced.
1. Turn on this model's power. "NO DISC" is displayed on the FL tube.
2. Press the this model's 1and 9 buttons simultaneously. "INITIALIZING" is displayed on the FL tube.
3. The display on the FL tube switches to "INITIALIZED", the "NO DISC" display reappears and initialization is
completed.
Service tools
Measuring Disc: CD/TCD-784
DVD/VT502 or TDV-520A
BD/ABD-520 or BLX-108
z Refer to "MEASURING METHOD AND WAVEFORMS".
When you repair the BD MECHA UNIT, you can use the following JIG.
Please order to DENON Ofcial Service Distributor in your region if necessary.
Do not supply it : 232C (TTL) – USB conversion jig (Model: DUT-06635 by GeeeTech) : 1 Set
Part No. : 61205000300AS : 4P RE-PH CONN CORD (1000mm) : 1 Set
z Refer to "HOW TO REPLACE THE MAIN PCB & BD MECHAOR BD MECHA".
NOTE : • If step 3 does not work, start over from step 1.
• All user settings will be lost and this factory setting will be recovered after the set is initialized.
So make sure to note down your setting beforehand for restoring after the initialization.
Forward-SkipPLAY
ON/STANDBY

FRONT PANEL ASSY
Refer to "DISASSEMBLY
1. FRONT PANEL ASSY"
and "EXPLODED VIEW"
FRONT PANELASSY
(Ref. No. of EXPLODED VIEW : B)
DISPLAY PCB UNIT
(Ref. No. of EXPLODED VIEW : 6)
BD MECHA UNIT ASS'Y
Refer to "DISASSEMBLY
2. BD MECHA UNIT ASSY"
and "EXPLODED VIEW"
MAIN PCB UNITASSY
(Ref. No. of EXPLODED VIEW : A)
MAIN PCB UNIT ASS'Y
Refer to "DISASSEMBLY
3. MAIN UNIT ASSY"
and "EXPLODED VIEW"
MAIN PCB UNITASSY
(Ref. No. of EXPLODED VIEW : A)
POWER PCB UNIT ASS'Y
Refer to "DISASSEMBLY
5. POWER PCB UNIT"
and "EXPLODED VIEW"
POWER PCB UNIT
(Ref. No. of EXPLODED VIEW : 2)
IR PCB UNIT ASS'Y
Refer to "DISASSEMBLY
4. IR PCB UNIT"
and "EXPLODED VIEW"
IR PCB UNIT
(Ref. No. of EXPLODED VIEW : 2)
TOP COVER
9
DISASSEMBLY
• Disassemble in order of the arrow in the following gure.
• In the case of the re-assembling, assemble it in order of the reverse of the following ow.
• In the case of the re-assembling, observe "attention of assembling".
• If wire bundles are untied or moved to perform adjustment or replace parts etc., be sure to rearrange them neatly as
they were originally bundled or placed afterward.
Otherwise, incorrect arrangement can be a cause of noise generation.
About the photos used for "descriptions of the DISASSEMBLY" section
• The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as
"Shooting direction: ***".
• Refer to the diagram below about the shooting direction of each photograph.
• Photographs with no shooting direction indicated were taken from the top of the set.
The viewpoint of each photograph
(Shooting direction)
［View from the top］Front side
Shooting direction: B
Shooting direction: D
Shooting direction: C
Shooting direction: A

10
1. FRONT PANEL ASSY
(1) DetachtheLOADERPANEL.
(2) DisconnecttheconnectorwireandFFC.
(3) Lift up to unhook the claw and move in the direction of arrow to gradually pull out the assembly.
Top side ×4, Side ×2 (Left and right), Bottom ×3
Proceeding : TOP COVER →LOADER PANEL FRONT PANEL ASSY
→
Shooting direction: B
Pressed in metal rod having a mechanism for
emergency open, stretched out like a small hole
on the left side of the clip to.
18P-FFC【XP4】4P-PH【XP３】 Cut
Shooting direction: D
Shooting direction: C
Top side
Bottom side
Side

11
2. BD MECHA UNIT ASSY
※Please ensure ESD protection prior to handling the BD MECHA.
(1) Removethescrews.
ScrewofMechacover× 4
(2) Remove the screws.
Screw of BD's Mecha ×4
(3) Disconnect the connector wire and FFC cable.
45P-FFC【J2】, 9P-FFC【J4】
From the left side of the BD's Mecha, remove the screw.
MECHA COVER
Proceeding : TOP COVER →BD MECHA UNIT ASSY
→

12
3. MAIN PCB UNIT ASSY
(1) Removethescrews.
RemovethescrewsfromREARPANEL×2
RemovethescrewsfromTOPPANEL×4
(2) DisconnecttheconnectorwireandFFC.
Disconnect13P-FFC【XP8】
, 12P-PH【XP1】
Proceeding : TOP COVER MAIN PCB UNIT ASSY
→

13
4. POWER PCB UNIT ASSY
(1) Removethescrews.
RemovethescrewsfromTOP×5
(2) DisconnecttheconnectorwireandFFC.
Disconnect 12P-PH【CN502/503】
, 3P-VH【CN501】
5. IR PCB UNIT ASSY
(1) Removethescrews.
RemovethescrewsfromREARPANEL×2
(2) DisconnecttheconnectorwireandFFC.
Disconnect13P-FFC【XP8】
Proceeding : TOP COVER POWER PCB UNIT ASSY
→
Proceeding : TOP COVER IR PCB UNIT ASSY
→

14
REMOVING DISCS
(1) Remove the Top Cover.
(2) Open the CD tray.
Shooting direction: D
Pressed in metal rod having
a mechanism for emergency
open, stretched out like a small
hole on the left side of the clip to.

Disc no read, unsteady playback, etc.
Laser drive current (Iop) check.
The MAIN PCB & BD MECHA
or the BD MECHA replacing.
Current value of the BD Iop is ±6[mA],
DVD or CD Iop is ±12[mA] or more the
initial value.
qCheck the laser drive current value
Disc no read, unsteady playback, etc.
ABD-RE540W disc playability check
(Load ve times of following disc)
Disc cannot play.
The MAIN PCB & BD MECHA
or the BD MECHA replacing.
wCheck the playability disc
15
DIAGNOSTICS OF OPTICAL PICKUP
Make failure diagnostics of the Optical Pickup as follows.
q
If the laser drive current (Iop) becomes more than BD : ± 6 [mA], DVD or CD : ±12 [mA] of the initial value, the Optical
Pickup should be replaced.
The laser drive current initial value is checked by "Iop checked Method" of next page.
w Load ve times of following disc again and playing it for one minute. It becomes the aim of the Optical Pickup
exchange when it cannot play.
BD-RE ABD-RE540W(made by ALMEDIO)
In case of replacing the Pickup, change the whole part of the MAIN PCB & BD MECHA or BD MECHA.
No mechanical adjustment is necessary after the replacement. (HOW TO REPACE THE MAIN PCB & BD MECHAOR
THE BD MECHA (page 17))
Laser drive current initial value:
FL Display (The display part of 13 digits)
CD : 1234567891011 12 13
T21:mmmm:nnnn
FL Display (The display part of 13 digits)
DVD : 1234567891011 12 13
T22:mmmm:nnnn
FL Display (The display part of 13 digits)
BD(SL) : 1234567891011 12 13
T23:mmmm:nnnn

16
1. Iop checked Method
Select the laser ON/OFF(CD/DVD/BD)mode of the test mode, and check the Iop value of CD laser, DVD laser or BD
laser. (Refer to "6. Test mode")
FL Display (The display part of 13 digits)
1234567891011 12 13
T2 LaserOnOff
Laser current check
Press the 8or 9 button to display the laser current value, and then select [X].
Check the current value of Iop (nnnn)
FL Display (The display part of 13 digits)
1234567891011 12 13
T2X:mmmm:nnnn
(X=1 : CD laser mode, 2 : DVD laser mode, 3 : BD(SL) laser mode
(mmmm[mA] : Initial value, nnnn[mA] : Current value)
2. To clear the accumulated laser on time
Press the 1 button while the accumulated laser on time is displayed ("TC1, "TC2", "TC3" ) until "TC4 ＊clear??"
appears at the display. If the 1 button is pressed, the accumulated laser on time of CD, DVD and BD is cleared
FL Display (The display part of 13 digits)
1234567891011 12 13
TC4*--clear??
When "TC1", "TC2" or "TC3" is selected with the 8or 9 button, "mmmmmm" is displayed as "0" so you can check.
FL Display (The display part of 13 digits)
1234567891011 12 13
TCY---mmmmmmh
(Y=1 : CD, 2 : DVD , 3 : BD, mmmmmm : Time)

17
HOW TO REPLACE THE MAIN PCB & BD MECHA OR BD MECHA
NOTE: The optical pick-up laser diode (LD) is instantly degraded or damaged by static electricity or a power
surge. When handling the BD MECHA UNIT, always be sure to earth yourself, and use an earth mat on the
workbench and oor for grounding.
• BD MECHA UNIT Replacement Conditions
If the laser amperage (Iop) exceeds the stipulated range (see the laser on/off mode in test mode (page 25)), replace the
BD MECHA or replace the MAIN PCB & BD MECHA. If other problems occur, replace the MAIN PCB & BD MECHA.
Stipulated range: For BD, within ±6 [mA] of the initial value; for DVD/CD, within ±12 [mA] of the initial value.
• The following two parts are specied as service parts for the MECHA UNIT.
1. MAIN PCB & BD MECHA : (Part No. : 919304100180D)
2. BD MECHA : (Part No. : 919304100230S)
1. How to Replace the MAIN PCB & BD MECHA
(1) Refer to the removal procedure, and remove and replace the MAIN PCB & BD MECHA. (see "DISASSEMBLY")
(2) Follow the rmware update procedure, and update the rmware to the latest version.
(see "VERSION UPGRADE PROCEDURE OF FIRMWARE")
2. How to Replace the BD MECHA
2.1. Devices Used
1. PC
2. USB - 232C (TTL) conversion jig (Model: DUT-06635 by GeeeTech) (Do not supply)
3. 4P RE-PH CONN CORD (1000mm) (Part No. : 61205000300AS)
4. Write software (5.12.71(8550+KES470)_1Dscan.zip)
2.2. Replacement Overview
(1) Before replacing the UNIT, write all of the UNIT data of the unit to be replaced onto the set.
(2) After performing (1), replace the UNIT.
(3) Congure the settings for the set in which the UNIT was replaced.
2.3. Before replacing
[Preparation]
1. Set unit before replacing the UNIT
2. PC with write software (5.12.71(8550+KES470)_1Dscan.zip) installed
3. USB - 232C (TTL) conversion jig
4. UNIT for replacement

18
[Connection]
(1) Connect the 232C (TTL) side 4P PH connector of the USB - 232C (TTL) conversion jig to the MAIN PCB of the set.
(2) Connect the USB side of the USB - 232C (TTL) conversion jig to the PC.
[Writing new optical pick-up data ]
• Barcode position of optical pick-up unit
(1) Switch on the power on of the set before the BD MECHA is replaced.
(2) Decompress the 5.12.71(8550+KES470)_1Dscan.zip folder and start the "Rpower.exe".
(3) A pop-up is displayed. Click "OK".
(4) Click "OK".
Jumper pin : 3.3V fmark
MAIN PCB
4P RE-PH CONN CORD (1000mm)
USB - 232C(TTL) conversion jig
CON1
View from the top
1Dimensional Bar Code
BD MECHA for replacement

19
(5) On the screen below, select "ComPort XX".
Select the USB - 232C (TTL) conversion jig port.
(6) Enter the Bar Code BOX 32-digit hexadecimal number listed at the bottom of one-dimensional bar code replacement
for the BD MECHA.
One dimension of bar code data can stick to reading, Bar Code BOX in bar code leaders and can input.
Note: The bar code data of the optical pickup, please do not enter the wrong data. Please do not confused
with other data of the optical pickup also.

20
(7) Click Write(F2).
(8) When “Pass” changes to green, writing to the Flash ROM of the MAIN PCB is complete.
(9) Switch off the set unit power, and remove the 232C (TTL) side 4P PH connector of the USB - 232C (TTL) conversion
jig from the MAIN PCB (CON1).