Dentsply Sirona Heliodent Plus User manual

New as of:
Installation Instructions
03.2018
Heliodent Plus
English
=
Cover Page Installation Instructions

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 3
Dentsply Sirona Table of contents
Installation Instructions Heliodent Plus
båÖäáëÜ
Table of contents
1About these Installation Instructions........................................................................ 6
1.1 Scope ........................................................................................................... 6
1.2 Round and angular support arm system ...................................................... 6
1.3 Other documentation required...................................................................... 6
1.4 Structure of the document............................................................................ 7
1.4.1 Identification of the danger levels.................................................... 7
1.4.2 Formats and symbols used ............................................................. 7
2General safety information ...................................................................................... 8
3Installation options................................................................................................... 10
4Delivery and transport ............................................................................................. 13
4.1 Transport, storage, and operating conditions............................................... 13
4.2 Checking the delivery................................................................................... 13
5Required materials .................................................................................................. 15
5.1 Required installation material ....................................................................... 15
5.2 Required tools and auxiliary materials ......................................................... 16
6Installation ............................................................................................................... 18
6.1 Installing the wall adapter............................................................................. 18
6.1.1 Preparation...................................................................................... 18
6.1.2 Installation (concealed installation) ................................................. 20
6.1.3 Installation (surface installation)...................................................... 21
6.2 Installing the round support arm and scissor arm ........................................ 22
6.2.1 Installing the support arm................................................................ 22
6.2.2 Installing the scissor arm................................................................. 23
6.3 Installing the angular support arm and scissor arm...................................... 26
6.3.1 Installing the angular support arm................................................... 26
6.3.2 Installing the angular scissor arm.................................................... 27
6.3.3 Adjusting the brake.......................................................................... 29
6.4 Preparing the protective housing.................................................................. 30
6.5 Installing the remote control and the remote timer....................................... 31
6.5.1 Wall-mounted installation ................................................................ 31
6.5.2 Modifying the remote timer.............................................................. 33
6.6 Installing the manual release holder............................................................. 35
6.6.1 Installation on the wall..................................................................... 35
6.6.2 Installation on the cover (wall module)............................................ 36
6.6.3 Installation on the protective cover of the remote control................ 37

62 14 972 D 3507
4D 3507.031.01.15.02 03.2018
Table of contents Dentsply Sirona
Installation Instructions Heliodent Plus
7Electrical connection ................................................................................................ 38
7.1 Connecting the arm cable ............................................................................. 38
7.2 Connecting the grounding strap.................................................................... 39
7.3 Connecting the control panel ........................................................................ 40
7.3.1 Direct connection (standard)............................................................ 40
7.3.2 Connection to the remote timer........................................................ 41
7.4 Connecting the release and the door contact ............................................... 42
7.4.1 General ............................................................................................ 42
7.4.2 Overview .......................................................................................... 42
7.4.2.1 Removing the EMC plate .................................................. 45
7.4.3 Installation option 1 .......................................................................... 46
7.4.4 Installation option 2 .......................................................................... 47
7.4.5 Installation option 3 .......................................................................... 49
7.4.6 Installation option 4 .......................................................................... 51
7.4.7 Installation option 5 .......................................................................... 53
7.4.8 Installation option 6 .......................................................................... 55
7.4.9 Installation option 6.1 ....................................................................... 58
7.4.10 Installation option 7 .......................................................................... 61
7.4.11 Installation option 8 .......................................................................... 62
7.5 Completion .................................................................................................... 63
7.6 Preparing the power connection ................................................................... 64
8Starting up................................................................................................................ 66
8.1 Functional test............................................................................................... 66
8.1.1 Overview .......................................................................................... 66
8.1.2 Checking the protective ground wires .............................................. 67
8.1.3 Checking the unit leakage current.................................................... 69
8.1.4 Checking the X-ray tube assembly .................................................. 70
8.1.5 Checking the tube current................................................................ 70
8.1.6 Checking exposure time and high voltage kV .................................. 72
8.1.7 Checking the deadman function....................................................... 73
8.2 Attaching the housing covers ........................................................................ 74
8.2.1 Support arm cover............................................................................ 74
8.2.2 Attach the EMC additional plate for the wall adapter to the power
supply
75
8.2.3 Wall module ..................................................................................... 76
8.2.4 Remote control................................................................................. 77
8.2.5 Remote timer.................................................................................... 78
8.3 Individual unit adaptation .............................................................................. 79

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 5
Dentsply Sirona Table of contents
Installation Instructions Heliodent Plus
båÖäáëÜ
9Final work ................................................................................................................ 80
10 Appendix.................................................................................................................. 81
10.1 Selection of the release button..................................................................... 81
10.2 Service routines............................................................................................ 82
10.2.1 Operation......................................................................................... 82
10.2.2 Service routine S15......................................................................... 83
10.2.3 Adjustment following increased AL filter value................................ 84
10.2.3.1 Adapting radiation times................................................... 84
10.3 Replacing old units....................................................................................... 85
10.3.1 Overview ......................................................................................... 85
10.3.2 Replacement of horizontally mounted old units with an adapter
plate
85
10.3.3 Replacement of vertically mounted old units................................... 88
10.4 Installing the mobile stand............................................................................ 91

62 14 972 D 3507
6D 3507.031.01.15.02 03.2018
1About these Installation Instructions Dentsply Sirona
1.1Scope Installation Instructions Heliodent Plus
1About these Installation Instructions
1.1 Scope
These Installation Instructions describe the installation of the Heliodent
Plus extraoral X-ray system. They are intended for use exclusively by
trained and authorized distributors and service technicians.
1.2 Round and angular support arm system
The Heliodent Plus is available with a round and angular support arm
system.
In the images which do not exclusively demonstrate the angular support
arm system, the round support arm system is shown.
1.3 Other documentation required
In addition to these installation instructions you will require the following
documentation:
Drilling template
● Heliodent Plus drilling template: Order No. 62 15 003
Wiring diagrams
● Heliodent Plus Wiring References: Order No. 62 15 086
Service manual
● Heliodent Plus Service manual: Order No. 62 15 102

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 7
Dentsply Sirona 1About these Installation Instructions
Installation Instructions Heliodent Plus 1.4Structure of the document
båÖäáëÜ
1.4 Structure of the document
1.4.1 Identification of the danger levels
To prevent personal injury and material damage, please observe the
warning and safety information provided in these operating instructions.
Such information is highlighted as follows:
Tip: Information for simplifying work.
1.4.2 Formats and symbols used
The formats and symbols used in this document have the following
meaning:
DANGER
An imminent danger that could result in serious bodily injury or death.
WARNING
A possibly dangerous situation that could result in serious bodily injury
or death.
CAUTION
A possibly dangerous situation that could result in slight bodily injury.
NOTICE
A possibly harmful situation which could lead to damage of the product
or an object in its environment.
IMPORTANT
Application instructions and other important information.
Prerequisite
1. First action step
2. Second action step
or
➢ Alternative action
Result
➢Individual action step
Prompts you to do something.
See “Formats and symbols
used [ → 7]”
Identifies a reference to another text
passage and specifies its page
number.
● List Designates a list.
“Command / menu item” Indicates commands, menu items or
quotations.

62 14 972 D 3507
8D 3507.031.01.15.02 03.2018
2General safety information Dentsply Sirona
Installation Instructions Heliodent Plus
2General safety information
DANGER
Potentially lethal shock hazard:
➢It is essential that you switch the line voltage OFF at the main switch
of the building installation before beginning installation of the unit!
DANGER
Potentially lethal shock hazard!
Fixed connection!
Installing a mains plug instead of the specified fixed connection infringes
international medical regulatory actions and is prohibited. In case of
error, this puts patients, users, and other parties seriously at risk.
WARNING
Radiation protection
The valid radiation protection regulations and measures must be
observed. The statutory radiation protection equipment must be used.
In case of malfunctions, cancel the exposure immediately by letting go
of the exposure release button.
CAUTION
Risk of injury!
➢The installation must be carried out in accordance with the
requirements stated in our Installation Instructions.
➢Installation may be carried out only by personnel specifically
authorized by Dentsply Sirona.
CAUTION
Electromagnetic compatibility:
✔The unit should not be operated in the immediate vicinity of other
devices (see also "Installation Requirements, Chapter on EMC“).
➢If this proves to be unavoidable, the unit should be monitored to
ensure that it is operating properly.
NOTICE
Electrical components of the unit can be destroyed.
Prior to opening the unit
➢Please comply with the usual precautionary measures for handling
printed circuit boards (ESD).
➢Make sure you touch a ground point to discharge yourself prior to
touching the components.
➢Use an ESD wrist band and connect it to the protective ground wire.

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 9
Dentsply Sirona 2General safety information
Installation Instructions Heliodent Plus
båÖäáëÜ
CAUTION
Gaps appear between the internal hinges when moving the angular
Heliodent Plus stay arm.
Fingers may be crushed in these gaps.
➢Ensure that you never place your fingers in the gaps between the
hinges, neither during operation nor for cleaning purposes.
WARNING
Modifications to the product
Modifications which may affect the safety of the operators or third
parties are prohibited by law!
CAUTION
No additional components on the support arm system
Attaching additional components to the support arm system is not
permitted.
CAUTION
Heliodent Plus and LEDview Plus are authorized for use on the ceiling
model for fixed connections only!
Please observe the line voltage specifications on the rating plates of the
ceiling MODEL and Heliodent Plus wall adapter.

62 14 972 D 3507
10 D 3507.031.01.15.02 03.2018
3Installation options Dentsply Sirona
Installation Instructions Heliodent Plus
3Installation options
Designations for release buttons and door contact
● Manual release S3
– Coiled cable
● Release key on the control membrane S4
– Directly connected to control board DX4
● Remote control release key S9
– Integrated in remote control housing
● Door contact (safety circuit) S7
Installation option 1
Release in the treatment room without remote control
● Release
– Manual release S3
Installation option 2
Release in the treatment room with remote control
● Release
– Manual release S3
or
– Remote control release key S9
Installation option 3
Release in the treatment room withRemote Timer
● Release
– Manual release S3
or
– Release key on the control membrane S4
NOTICE
Length of cable supplied for Remote Timer approx. 10 meters (393")
(must not be extended).
Conduit int. dia. at least 12 mm (1/2").

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 11
Dentsply Sirona 3Installation options
Installation Instructions Heliodent Plus
båÖäáëÜ
Installation option 4
Release outside of the X-ray room with remote control
● Release
– Manual release S3
or
– Remote control release key S9
Installation option 5
Release outside of the X-ray room withRemote Timer
● Release
– Manual release S3
or
– Release key on the control membrane S4
Installation option 6
Release outside of the X-ray room with remote control, door contact
safety circuit
● Door contact
– Door contact S7 wired to the wall adapter
● Release
– Manual release S3
or
– Remote control release key S9
NOTICE
Installation prerequisites
Use of the remote control is permissible only if the yellow X-Ray LED is
visible to the operating personnel during radiation release.
NOTICE
Length of cable supplied for Remote Timer approx. 10 meters (393")
(must not be extended).
Conduit int. dia. at least 12 mm (1/2").
NOTICE
Installation requirement
Use of the remote control is permissible only if the yellow X-Ray LED is
visible to the operating personnel during radiation release.

62 14 972 D 3507
12 D 3507.031.01.15.02 03.2018
3Installation options Dentsply Sirona
Installation Instructions Heliodent Plus
Installation option 6.1
Release outside of the X-ray room with remote control, door contact
safety circuit
● Door contact
– Door contact S7 wired to the remote control housing
● Release
– Manual release S3
or
– Remote control release key S9
Installation option 7
Release outside of the X-ray room with Remote Timer, door contact
safety circuit
● Door contact
– Door contact S7
● Release
– Release key on the control membrane S4
Installation option 8
Release outside of the X-ray room with Remote Timer, door contact
safety circuit
● Door contact
– Door contact S7 wired to Remote Timer
● Release
– Manual release S3
NOTICE
Installation requirement
Use of the remote control is permissible only if the yellow X-Ray LED is
visible to the operating personnel during radiation release.

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 13
Dentsply Sirona 4Delivery and transport
Installation Instructions Heliodent Plus 4.1Transport, storage, and operating conditions
båÖäáëÜ
4Delivery and transport
4.1 Transport, storage, and operating conditions
4.2 Checking the delivery
All products from Dentsply Sirona are carefully checked prior to shipment.
Please perform an incoming inspection immediately after delivery.
1. Check the delivery note to ensure that the consignment is complete.
2. Check whether the product shows any visible signs of damage.
If return shipment is required, please use the original packaging for
shipment.
Heliodent Plus packaging, bottom part
Transport, storage and operating conditions:
Transport and storage
conditions:
Temperature: -40°C – +70°C (-40°F –
158 F)
Relative humidity: 10% – 95%
Air pressure: 500 hPa – 1060 hPa
Operating conditions: Ambient temperature +10°C – +35°C
(50°F – 95°F)
With room temperatures > 35°C (> 95°F)
Dentsply Sirona recommends the use of
an air conditioning system.
Relative humidity: 30% - 85% (no
condensation)
Operating altitude: ≤ 3000 m
NOTICE
Damage during transport
If the product was damaged during transport, please contact your
carrying agent.

62 14 972 D 3507
14 D 3507.031.01.15.02 03.2018
4Delivery and transport Dentsply Sirona
4.2Checking the delivery Installation Instructions Heliodent Plus
Heliodent Plus packaging, top part

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 15
Dentsply Sirona 5Required materials
Installation Instructions Heliodent Plus 5.1Required installation material
båÖäáëÜ
5Required materials
5.1 Required installation material
● The permissible tensile force of the selected attachment must at least
equal the tensile force listed above.
● Matching wood screws for wooden beams are included in delivery.
● For all other wall structures, special wall anchors must be purchased
from a selected dealer. The wall anchors and screws should be
identical for every attachment point.
● Alternatively, an anchor plate can be used as a counter bearing. In
this case, M8 threaded rods of the appropriate length for the wall
(thickness of the wall + 2 x mounting plate thickness + attachment
material) are required.
CAUTION
Observe wall properties
In installation situations, the technician is responsible for the
assessment of wall properties and selecting the method of attaching the
unit to the wall.
KTensile force per screw
3600 N (800 lbf) if L ≤ 700mm (27 1/2“)
4200N(950 lbf) if L ≤ 950mm (37 3/8“)
LLength of support arm
MMounting plate (supplied)
NAnchor plate
OThreaded bolt M8
K
L
M
N
O

62 14 972 D 3507
16 D 3507.031.01.15.02 03.2018
5Required materials Dentsply Sirona
5.2Required tools and auxiliary materials Installation Instructions Heliodent Plus
5.2 Required tools and auxiliary materials
● Drill or drill hammer, depending on the ground
● Masonry drill bit 10 mm (3/8")
● Masonry drill bit 6 mm (1/4")
● Wood drill bit 6 mm (1/4")
● Metal drill bit 4.3 mm (3/16")
●Hammer
● Center punch
● Spirit level
● Scissors

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 17
Dentsply Sirona 5Required materials
Installation Instructions Heliodent Plus 5.2Required tools and auxiliary materials
båÖäáëÜ
● Screwdriver, Torx®, sizes T10, T15 and T20
● Slotted screwdriver, sizes 2.5mm and 3.5 mm (3/32" and 9/64")
● Allen wrench size 13mm, 4mm
● Socket wrench or ratchet wrench (with extension), size 13 mm
● Retaining ring pliers for outside rings (shafts)
● Multimeter or ammeter (battery-operated)
● Test unit to measure unit leakage current:
Dentsply Sirona recommends an automatic tester (example
illustration) which complies with standard IEC 62353.
If you do not use an automatic tester, please pay attention to the
specifications in the standard IEC 62353.
●Power source for protective ground wire test
Technical data:
– No-load voltage max. 6V
– Short-circuit current at least 5A - max. 25A

62 14 972 D 3507
18 D 3507.031.01.15.02 03.2018
6Installation Dentsply Sirona
6.1Installing the wall adapter Installation Instructions Heliodent Plus
6Installation
6.1 Installing the wall adapter
For Heliodent Plus on the mobile stand, see section Installing the
mobile stand [ → 91]
6.1.1 Preparation
Attachment points
These installation instructions distinguish between wall-mounted
installation (masonry) and installation on wooden beams.
●Wall-mounted installation: 3 attachment points
– Positions A1, A3 and A4
●Wooden beam installation: 2 attachment points
– Positions A2 and A4
Getting started
NOTICE
Covering up old installation sites
Possibilities for using or covering up the installation sites of old units are
described in the section "Replacing old units" [ → 85].
DANGER
Shock hazard!
Be sure to switch off the line power supply before connecting the line
voltage!

62 14 972 D 3507
D 3507.031.01.15.02 03.2018 19
Dentsply Sirona 6Installation
Installation Instructions Heliodent Plus 6.1Installing the wall adapter
båÖäáëÜ
1. For concealed installation only: Cut out cable bushings (B) and (F) in
the drilling template.
2. Pull the cable through the cable bushings (B) and (F).
3. Align the drilling template using a spirit level and attach it to the wall.
4. Center punch the fastening points and drill according to the type of
fastening used.
- When securing with an anchor plate, drill into wall with a ⌀ 8mm drill
bit.
- If installing with wall plugs, drill according the the wall plugs used
(max. ⌀ 10mm) and insert the wall plugs.
- In case of a wooden wall, drill holes at least 80 mm deep with a ⌀
6mm wood drill bit.
5. Remove the drilling template.
B
F
A4
A2 A3A1

62 14 972 D 3507
20 D 3507.031.01.15.02 03.2018
6Installation Dentsply Sirona
6.1Installing the wall adapter Installation Instructions Heliodent Plus
6.1.2 Installation (concealed installation)
1. Remove wall adapter (P1) from the packaging.
2. For the power cable: Carefully punch out opening B in the wall
adapter with a punch.
3. Position the wall adapter on the prepared installation location.
4. Pull the power cable through the opening (B) in the wall adapter.
5. For remote control / Remote Timeronly (cable L6 or L9): Pull the
cable through the opening (F) in the wall adapter.
6. Screw the wall adapter onto the wall loosely to hold it in place.
7. Align the wall adapter with a spirit level and attach the wall adapter
securely with suitable screws and washers, depending on the type of
attachment.
CAUTION
Risk of damage
Make sure that board DX1 is not damaged during installation!
Observe ESD protective measures!
L1
PE
N´
N
F
L9/L6
B