Dentsply Sirona CEREC Primescan AC User manual

New as of:
09.2018
CEREC Primescan AC, Primescan AC,
CEREC Omnicam AC, Omnicam AC
Unpacking and Installation Instructions
English

Table of contents Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
26681790 D3696
D3696.031.01.01.0209.2018
Table of contents
1Packaging box ........................................................................................................ 3
2Removing parts from the lower section of the packaging ....................................... 4
3Taking the unit out of its packaging ........................................................................ 5
4Assembling the unit ................................................................................................ 6
4.1 Opening the service cover ........................................................................... 6
4.2 Insert battery (optional) ................................................................................ 7
4.3 Installing the monitor.................................................................................... 8
4.4 Using a trackball (if provided, depending on the configuration)................... 10
4.5 Plug connections.......................................................................................... 11
4.6 Inserting the USB connector wireless module ............................................. 11
4.7 Closing the service cover............................................................................. 12
4.8 Using a power cable holder (accessories) ................................................... 12
5Putting the system into operation ........................................................................... 13
5.1 Switching the units on .................................................................................. 13
5.2 Configure software....................................................................................... 14

Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
1 Packaging box
6681790 D3696
D3696.031.01.01.0209.2018 3
1Packaging box
IMPORTANT
Unpacking and installation must be carried out by authorized
specialist personnel (technicians) in accordance with the unpacking
and installation instructions.
1. Open the packaging box at the top and remove it.
2. Remove these unpacking and installation instructions from the
upper part of the packaging and follow them accordingly.
3. Remove the battery (A) and accessories (B) from the upper part of
the packaging.

2 Removing parts from the lower section of the packaging Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
46681790 D3696
D3696.031.01.01.0209.2018
2Removing parts from the lower section of
the packaging
1. Remove the monitor cable and place this to one side next to the
packaging.
2. Lift off the upper part of the packaging (A).
3. Remove the monitor (B) from the lower part of the packaging and
place it down on an even surface on its front, protected so that this
is not damaged.
4. Remove the scanner (C).

Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
3 Taking the unit out of its packaging
6681790 D3696
D3696.031.01.01.0209.2018 5
3Taking the unit out of its packaging
1. Pull the two foil bags and the felt pad from the rollers.
2. Place the lower part of the packaging in an upright position.
3. Hold onto the unit on the handle and pull it out.
4. Remove the plastic film and felt from the unit.

4 Assembling the unit Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
66681790 D3696
D3696.031.01.01.0209.2018
4Assembling the unit
4.1 Opening the service cover
1. Turn the cabinet bolt of the service cover with a coin or a
screwdriver (> 5) approx. 90° counterclockwise as far as it will go.
2. Press down the service cover as far as it will go and remove it.

Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
4 Assembling the unit
6681790 D3696
D3696.031.01.01.0209.2018 7
4.2 Insert battery (optional)
A Service cover D 2 guide rails
B Storage battery E 2 guide pins
C 2 fastening screws
➢ Slide in the storage battery using the guide rails and guide pins up
to the stop and screw it in place with 2 fastening screws (C).

4 Assembling the unit Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
86681790 D3696
D3696.031.01.01.0209.2018
4.3 Installing the monitor
NOTE
Risk of damage to the display caused by mechanical impact.
➢ Do NOT subject active display area to any mechanical pressure.
➢ NEVER touch active display area with sharp or pointed objects.
Installing the monitor
1. Loosen and remove the monitor brake (2 screws).
2. Unscrew the locking plate mini DIN connector (1 screw A).

Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
4 Assembling the unit
6681790 D3696
D3696.031.01.01.0209.2018 9
3. Guide the 4 cables through the openings and insert the monitor.
4. Screw the monitor brake on as shown with the 2 screws.
5. Unscrew the screw with a tooth washer. Insert the eyelet of the
ground cable (L14) as shown between the screw head and tooth
washer. Fasten the ground cable using the screw.
6. Plug the connector of cable (L4) into socket (X101) of the supply
board.

4 Assembling the unit Dentsply Sirona
Unpacking and Installation Instructions CEREC Primescan AC, Primescan AC, CEREC Omnicam AC, Omnicam AC
10 6681790 D3696
D3696.031.01.01.0209.2018
7. Insert the USB connector.
8. Insert the HDMI connector.
9. Re-tighten the locking plate mini DIN connector with 1 screw (A).
10. Route the cables and clip them into the holders.
11. Pull the felt pad from the monitor.
4.4 Using a trackball (if provided, depending on the
configuration)
➢ Use the trackball in the recess (spherical calotte/spherical cap) on
the operator console.