Denver SW-500 User manual

Instruction Manual
Smart Watch
SW-500
www.denver-electronics.com
Before operating this product, please read this instruction
manual carefully and completely.

1
Feature
•1.3-inch IPS full screen display
•Multi-Sport Mode (Running, Walking, Hiking,
Biking, Indoor Run & Trail Run)
•Track your sport performance
•Provide comprehensive GPS location
•Digital Crown integrated, rotate it to change the
menu easily
•Built-in HR sensor, monitor your heart rate and
set your heart rate zone
•Built-in altimeter, barometer & temperature
•Monitor your daily activity and sleep
•Built-in sedentary reminder
•Synchronize phonebook, answer or reject calls
from your wrist
•Display SMS, emails, calendar events and social
media activity
•Smart wake-up, raise or shake your arm to wake
up the device
•Remote control music playback, remote capture
photo on your Smartphone
•Built-in loudspeaker and Microphone
•Built-in 350mAh Li-poly battery, up to 5-7 days
standby time
•Fully compatible with iOS7 or above and Android

2
4.4 or above
•Different design styles for your different
occasions and preferences
Overview
Smart Watch
1. MIC
2. Barometer sensor
3. Touch screen
4. Shortcut key for
Sport mode
5. Digital crown
6. Power button
7. Speaker
8. Heart rate sensor
9. POGO-Pin Charging
terminals
POGO-Pin Charger
10. POGO-Pin
11. Micro-USB port
Charging
•If you use a Power Adaptor (Not included), Power

3
Adaptor current is: 5V, 500mA.
•It takes 2-hours to fully charge the smart watch,
please follow steps below to charge.
1. Put the charging cradle
beneath the watch. Make
sure the POGO-pins on the cradle
fit correctly onto the charging
terminals on the back of smart
watch.
2. Connect the charging cradle
with the USB cable
3. Plug the big end of the USB cable to a power
source
Charging when power off Charging when power on
How to use
•Turn on: Hold press power button in 3 seconds
•Go to main menu: Swipe from right to left on watch
face interface
•Switch main menu: Swipe up/ down
•Confirm: Tap the icon or press digital crown

4
•Exit: Swipe from left to right
•Return to watch face interface: Short press power
button on any interfaces
•Sport mode shortcuts: Press the upper button
•Check notifications: Swipe from left to right on
watch face interface
•Switch submenu/ shortcuts: Swipe up/ down or
Turn digital crown
•Turn off: Hold press power button in 3 seconds
How to calibrate the sensor
In the settings inside, there is a “Sensor calibration”
option.
If you find the temperature, altitude, pressure of the
watch are wrong, you can calibrate the sensor to
make the watch display more accurate. (We will make
sensor calibration for each device before packing
when mass production)

5
The steps to calibrate the sensor：
Temperature: Settings-> Sensor calibration->
Temperature, set up the correct temperature value
and click “OK”.
Pressure: Settings-> Sensor calibration-> Pressure,
set up the correct pressure value and click “OK”.
Altitude: Settings-> Sensor calibration-> Altitude, if
you select “Manual”, set up the correct altitude
value and click “OK”. If you select “Use GPS”, wait
for GPS located successfully, the watch will
automatically show the current altitude, then click
“OK’.
Calibration reference：

6
Temperature: You can refer to the thermometer to
calibrate the watch's temperature;
Pressure: If you are using iPhone, you can see the
current city pressure in the Weather application
Altitude: You can download an app called "GPS
Recorder", open your mobile phone location
service, and then refer to "Meter" interface
"Altimeter" in iOS system.
PS: If you use GPS to calibrate the altitude, please
operate in an open area.
If you need to calibrate both altitude and
atmospheric pressure, please calibrate the
atmospheric pressure first, then calibrate the
altitude.
If you go to another city, you need to re-calibrate the
pressure and altitude on your watch.
The watch Units
you set up
Units of
Temperature
Units of Altitude
Metric
Degrees Celsius
(℃)
Meter (m)
Imperial
Degrees
Fahrenheit (℉)
Feet

7
Main Menu
When turning on smart watch, you will see the watch
face.
From watch face:
1.Go to Main Menu
a.Slide from right to left to enter into main menu.
b.Swipe up and down (or turn the digital crown)
to switch the main menu.
c. Click the icon (or press the digital crown) to
enter the corresponding menu. Slide from left
to right to return to the previous menu.

8
2.Go to Notification shortcut page
Slide from left to right
3.Go to other shortcuts page
Swipe up and down.
Pair with smart phone
Mobile phones requirement:
Android 4.4 and above
iOS7.0 and above
Search and download “Orunning” app from App store
or the Google Play Store on your smart phone.
Step 1: Pairing through the application “Orunning” to
sync activity data and notifications etc..
1.Enable Bluetooth on your smart phone
2.Open Orunning App on your smart phone, set up
your profile on Settings.
3.Tap “Connect Smart Watch” on Settings, select
the name of your smart watch (or your smart
watch name_LE if iPhone) in the list of devices for

9
connection.
Step 2: Pairing for calling function (Only for iPhone)
Go to iPhone “Settings””Bluetooth” and select
your smart watch name in the list of devices for
connection.
Remark:
•If the connection is successful, a check mark will
appear next to the name of your phone
•Make sure your smart phone is set to be “Visible
to all nearby Bluetooth device”.
•The smart watch will automatically pair with your
smartphone after the initial pairing is successful.
•The smart watch will auto-sync the date and time
with your smartphone.
Function
Watch face
You can press the power button to go to the watch
face interface quickly.