Denver SW-650 User manual

DENVER SW-650
GPS+GLONASS
smart watch
User manual

System requirements
he watch supports Android 4.4, iOS 8.0, Bluetooth 4.0 and above.
How to charge battery
Before start using the smart watch, please make sure the battery is
charged. For charging, please use the provided magnet charging
cable. he recommended power adaptor current is 5V, 1A.
It takes about 3 hours to fully charge the smart watch, please follow the
steps below to charge.
-Put the charging cable beneath the watch
-Make sure the POGO pins on the cable fit correctly onto the
charging terminals on the back of the watch.
-If correctly placed, the pins will stick to the charging terminals on the
back of the watch.
-hen connect the charging cable to the power source with the USB
connector.
Environment
Please don’t wear the smart watch when taking a hot shower or bath.
Don’t use the watch in very high and low temperature environment.
Otherwise, it may damage the watch.
Basic operation
-urn on: long press the power button for 3 seconds.
-Access sport modes: swipe from right to left on the watch face, or
press the top key.

-Navigate functions in the main menu: swipe up/down or vice versa
on the screen.
-Access the function menu: swipe from right to left on the screen.
-Confirm selection: tap the icon on the screen.
-Exit/back: swipe from left to right on the screen.
-Return to the watch face: short press the power button on any
screen.
-Sport mode shortcut: press the upper button
-Check notifications: swipe from left to right on the watch face.
-Switch submenu/shortcut: swipe up/down on the screen.
-urn off: long press the power button for 3 seconds.
-For more accurate measurement, it is recommended to wear the
watch around 1 cm behind the ulnar styloid joint, and close to the
skin.
Overview
1. Shortcut key for Sport mode/ back
2. Power button
3. ouch screen
4. Speaker
5. Charging terminals
6. Microphone
7. Heart rate sensor
Pair the watch with smartphone

Mobile phones requirement: Android 4.4 and above; iOS8.0 and
above.
Search and download “Denver SW-65 ” app from App store, or
Google Play Store on your smart phone. Or scan the following QR
code to install the app.
Make sure your smart phone is set to be “Detectable to all nearby
Bluetooth devices”.
Step 1: Pairing for calling function
a. On the Bluetooth settings of your smart phone, activate Bluetooth
and turn on the option of “Detectable to all nearby Bluetooth
devices
b. Enable Bluetooth device searching.
c. Select “SW-65 ” from the list of devices for connection
d. If the connection is successful, “Connected” appears next to SW-
65 device name.
On the Bluetooth settings of the smart watch, the checking mark for
Bluetooth connectivity appears next to the name of your phone.
he Bluetooth icon on the watch screen changes to blue .
e. After the successful initial pairing, the watch will automatically
connect with your phone, and the watch will automatically
synchronize date and time with your phone. You can also connect
the smart watch with your phone via the menu option of the
watch.

Step 2: Pairing through the “Denver SW-65 ” app to synchronize data
and notifications etc.
a. Pair the watch with your smartphone as described in step 1.
b. Open the Fundo app on your smart phone, and tap “More” in the
bottom right corner.
c. ap “Add device” on the top.
d. Select and tap SW-65 to connect.
e. If the connection is successful, “Connected” appears next to SW-65
device name, and the app will synchronize data from the smart
watch.
he Bluetooth icon on the watch screen shows both blue and green
.
Your phone is now connected to the watch and you are free to explore
all the functions of the watch in the various interfaces, directly by
swiping the touch screen of the watch.
For the full user manual in English, please visit our website and find the
product “SW-650” at www.denver-electronics.com