DEVA Broadcast DB9009-TX Instruction manual

Publish Date: 05-Oct-2023
How can the DB9009-TX be used
as an RTP Sender, sending audio to
DB9009-RX decoder used as an RTP Receiver
SET-UP INSTRUCTIONS

Contents
General information ......................................................................................................................... 4
DB9009-TX and DB9009-RX Set-up............................................................................................... 4
DB9009-TX RTP Sender set-up....................................................................................................... 4
DB9009-RX RTP Receiver set-up ................................................................................................... 7
Appendix A ......................................................................................................................................... 9
Appendix B ....................................................................................................................................... 13

THIS PAGE
IS INTENTIONALLY
LEFT BLANK

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 4 -
General information
The IP Audio encoder and decoder are controlled trough a build in WEB Server and a standard
web browser is used to monitor their status or to make some adjustments. To operate the devices
you need to know their IP Address. In case you are not aware of the IP Addresses and how to open
the WEB interface, please refer to “Appendix A - DB9009-TX Quick User Guide” on page 9
and “Appendix B - DB9009-RX Quick User Guide” on page 13.
This conguration is perfect if your setup requires only point-to-point connection. It has a
minimum and almost constant delay value (usually less than a second).
DB9009-TX AND DB9009-RX SET-UP
Prior to implementing the below written adjustments, the following requirements should be
fullled:
• DB9009-TX should be connected to a Network (Internet or LAN).
• DB9009-TX could be set with dynamic IP.
• DB9009-RX congured as RTP receiver with static IP.
• If the DB9009-RX is placed behind a router, you will have to make sure that the RTP
Receiver port is properly NAT forwarded.
DB9009-TX RTP SENDER SET-UP
1
2
3
1. Go to Settings> Input;
2. Choose the preferred audio signal input;
3. Press [Save];

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 5 -
4. Go to Settings> Encoding;
4
5
6
7
8
5. Assign Encoder type;
6. Assign Sample rate;
7. Assign desired Signal Quality.
The combination of these parameters will dene the stream bitrate (see Bitrate Guide table at
the bottom of this screen). The network connection should have enough bandwidth to process
all the streams. As a rough estimate, the bandwidth should be at least twice the stream’s bitrate,
multiplied by the number of simultaneous connections;
8. Press [Save];

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 6 -
9. Go to Settings> IP Audio;
9
10
13
11
12
10. Then in IP Audio Sender 1/2/3 section - specify Encoder from the drop-down menu;
11. Select RTP Sender from the drop down menu;
12. Specify URL, IP Address or Multicast group IP address, and Port of the RTP Receiver to
be used;
13. Press [Save].
FOR YOUR INFORMATION: A multicast address (Mcast group) is a logical identier for a
group of hosts in a computer network, that are available to process datagrams or frames intended
to be multicasted for a designated network service.
Multicast works in a local network or any other network that is specially set/congured. For
more information as regards how a multicast network could be set, please refer to your network
administrator.
For detailed information and instructions on how communication with the DB9009-TX can be
established, please refer to “Appendix A - DB9009-TX Quick User Guide” on page 9.

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 7 -
DB9009-RX RTP RECEIVER SET-UP
1
2
7
6
3
4
5
1. Go to Settings> IP Audio;
2. RTP Receiver section - Specify the audio player Port;
3. Specify Decoder to be used;
4. Set Gain;
5. Set Pre-buer;
6. If needed, specify Multicast group IP address;
7. Press [Save];
FOR YOUR INFORMATION: A multicast address (Mcast group) is a logical identier for a
group of hosts in a computer network, that are available to process datagrams or frames intended
to be multicasted for a designated network service.
Multicast works in a local network or any other network that is specially set/congured. For
more information as regards how a multicast network could be set, please refer to your network
administrator.

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 8 -
8. Go to Settings> Backup;
8
9
10
9. From the Source Priority section set the priority of the RTP Audio Player.
10. Press Save[10] to save the changes.
For detailed information and instructions on how communication with the DB9009-RX can be
established, please refer to “Appendix B - DB9009-RX Quick User Guide” on page 13.

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 9 -
Appendix A
DB9009-TX
Professional IP Audio Encoder
Quick User Guide
BEFORE YOU USE THIS PRODUCT
In order to be able to enjoy all the benefits of owning your new
DEVA product, please verify first that the latest software and
firmware release were installed.
Visit www.devabroadcast.com/downloads for the most
recent software and firmware downloads, prior the installation.

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 10 -
This
Quick user guide will make the installation of quick and easy. thesethe DB9009-TX Applying
principles,
you can simplify the process and save yourself extra time and effort. For more information
about
the Safety precautions and the Operating environment recommendations please refer to the
complete
ml- www.devabroadcast.com/downloadsuser anua .
1.
Install the unit on its operation place;
2.
Before connecting the AC Power, make sure that the fuse rating is in accordance with the mains supply
at
your location. DB9009-TX Power Supply Factory Settings are: 100-240 VAC; 1AFuse.;
3.
Connect the DB9009-TX to the TCP/IP network using a cable with RJ-45 connector;
4.
Optionally, connect the necessary for the configuration - audio cables (analog and/or digital), GPI and
etc.
There
are two options for access to the WEB Interface of DB . The first one is9009-TX IP Audio Decoder
through
manual identification of the IP address of the device, and the second one is through the Network
discovery
option ().For Windows 7 and above users only
DB
can be operated in methods. Through the Front panel navigational menu or via a standard9009-TX two
WEB
Browser.
For
more information about the Front panel navigational menu, please refer to the User Manual which can
be
found on www.devabroadcast.com/downloads
Connection
STEP 1
Network Settings
STEP 2
WEB Interface
STEP 3
Manual IP Address Identification
STEP 3.1
NOTE:
Due to the inability of some WEB Browsers to read the IP address format displayed on the screen
of the device, the numbers included in the IP Address must be written without the leading zeros.
For example: 192.168.020.068 192.168.20.68must be written as
1. Connect the device to a local network or to the Internet
by the applied LAN cable. the Front panelThrough
navigational menu pressing the OK button you will[]
enable you to ;enter the device main menu
2. [ IGHT]Using theR navigational buttonfind the
“”section at the end of the MenuStatus located ;
3. P[]ress the OK Button to enter the
“”
.Status Section
Viathe Front panel navigational menu pressthe
[] visualizeDOWN button.This operation will the screen
containing information about the IP Address of the
device;
4. Open a new WEB Browser and enter the device IP
address in the address field then press “Enter”;
5. that esA window requir username and password will
appear. Default values being - Username: user or
admin, Password: pass.

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 11 -
The
DB provides you with a protected access to the device settings. You can choose between two9009-TX
types
of log in:
1.
As an –ADMINISTRATOR
which
will give you full control
over
the settings (username:
admin
pass, password: );
2.
As a–this type of log-USER
in
will allow you to monitor the
devic
ewithout applying
settings
(username: ,user
password:
).pass
In
ordertomake the
n
ecessary adjustments to
the
device, please log in as
ADMINISTRA
TOR.
1.
nnclick on
""
Open Advanced sharing settings by clicking the Start butto , and the Control Panel .In the
search
box, type network , click Network and Sharing Center , and then, in the left pane click Change"""" "
advanced
sharing settings ."
2.
electS your current network profile.
3.
Click ,""Turn on network discovery
and
then click Save changes If you're"".
prompted
for an administrator password or
confirmation,
type the password or provide
confirmation.
4.
,To access the device openanew
Explorer
bar and click o.Ifn Network (1)
you
have successfully enabled the network
discovery
option, the device will be
displayed.
Double click on DB -TX (2)9009
will
open a new WEB browser window
requirin
sername and assword (gu p.For
more
information refer to .Step 4)
Network
discovery isanetwork setting that whether your computer can see (find) other computersdefines
and
devices on the network and whether other computers on the network can see your computer.By
default,
Windows Firewall blocks network discover but you can enable ity.
NOTE:
If you have already enabled this function on your computer just open a new Explorer bar and click
on
. The device be .If not follow the instructions from .will displayed , Step 3.2Network (1)
Network Discovery for Windows 7
STEP 3.2
Device Access
STEP 4
2
1
Asuccessful log in the Control Window will look like this

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 12 -
Please refer to the User manual for nformation ondetailed i
how to your deviceconfigure and explore .
Device Settings
STEP 5
Thank you for choosing DEVA!
Upon entering the device's settings, you will be able to apply the needed adjustments to the DB9009-TX.
In order the applied settings to be used press the [Save] button, placed on the bottom right part of each
screen.
For further information on the available options and features, which can beplease refer to the User Manual
found on www.devabroadcast.com/downloads, and the accompanying CD.

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 13 -
Appendix B
DB9009-RX
Professional IP Audio Decoder
Quick User Guide
BEFORE YOU USE THIS PRODUCT
In order to be able to enjoy all the benefits of owning your new
DEVA product, please verify first that the latest software and
firmware release were installed.
Visit www.devabroadcast.com/downloads for the most
recent software and firmware downloads, prior the installation.

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 14 -
This
Quick user guide will make the installation of quick and easy. thesethe DB9009-RX Applying
principles,
you can simplify the process and save yourself extra time and effort. For more information
about
the Safety precautions and the Operating environment recommendations please refer to the
complete
ml- www.devabroadcast.com/downloadsuser anua .
1.
Install the unit on its operation place;
2.
Before connecting the AC Power, make sure that the fuse rating is in accordance with the mains supply
at
your location. DB9009-RX Power Supply Factory Settings are: 100-240 VAC; 1AFuse.;
3.
Connect the DB9009-RX to the TCP/IP network using a cable with RJ-45 connector;
4.
Optionally, connect the necessary for the configuration - audio cables (analog and/or digital), GPI and
etc.
There
are two options for access to the WEB Interface of DB . The first one is9009-RX IP Audio Decoder
through
manual identification of the IP address of the device, and the second one is through the Network
discovery
option ().For Windows 7 and above users only
DB
can be operated in methods. Through the Front panel navigational menu or via a9009-RX two
standard
WEB Browser.
For
more information about the Front panel navigational menu, please refer to the User Manual which can
be
found on www.devabroadcast.com/downloads
Connection
STEP 1
Network Settings
STEP 2
WEB Interface
STEP 3
Manual IP Address Identification
STEP 3.1
1. Connect the device to a local network or to the Internet
by the applied LAN cable. the Front panelThrough
navigational menu pressing the OK button you will[]
enable you to ;enter the device main menu
2. [ IGHT]Using the R navigational button find the
“”section at the end of the MenuStatus located ;
3. P[]ress the OK Button to enter the
“”
.Status Section
Via the Front panel navigational menu press the
[] visualizeDOWN button.This operation will the screen
containing information about the IP Address of the
device;
4. Open a new WEB Browser and enter the device IP
address in the address field then press “Enter”;
5. that esA window requir username and password will
appear. Default values being - Username: user or
admin, Password: pass.
NOTE:
Due to the inability of some WEB Browsers to read the IP address format displayed on the screen
of the device, the numbers included in the IP Address must be written without the leading zeros.
For example: 192.168.020.068 192.168.20.68must be written as

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 15 -
Network
discovery isanetwork setting that whether your computer can see (find) other computersdefines
and
devices on the network and whether other computers on the network can see your computer.By
default,
Windows Firewall blocks network discover but you can enable ity.
1.
nnclick on
""
Open Advanced sharing settings by clicking the Start butto , and the Control Panel .In the
search
box, type network , click Network and Sharing Center , and then, in the left pane click Change"""" "
advanced
sharing settings ."
2.
electS your current network profile.
3.
Click ,""Turn on network discovery
and
then click Save changes If you're"".
prompted
for an administrator password or
confirmation,
type the password or provide
confirmation.
4.
,To access the device open a new
Explorer
bar and click o.Ifn Network (1)
you
have successfully enabled the network
discovery
option, the device will be
displayed.
Double click on DB -RX (2)9009
will
open a new WEB browser window
requirin
sername and assword (gu p.For
more
information refer to .Step 4)
NOTE:
If you have already enabled this function on your computer just open a new Explorer bar and click
on
. The device be .If not follow the instructions from .will displayed , Step 3.2Network (1)
Network Discovery for Windows 7
STEP 3.2
Device Access
STEP 4
The
DB provides you with a protected access to the device settings. You can choose between9009-RX
two
types of log in:
1.
As an –ADMINISTRATOR
which
will give you full control
over
the settings (username:
admin
pass, password: );
2.
As a–this type of log-USER
in
will allow you to monitor the
device
without applying
settings
(username: ,user
password:
).pass
In
ordertomake the
necessary
adjustments to
the
device, please log in as
ADMINISTRA
TOR.
2
1
Asuccessful log in the Control Window will look like this

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria
Tel: [phone], Fax: [phone]
E-mail: o󰀩[email protected] ,Web: www.devabroadcast.com
- 16 -
Please refer to the User manual for nformation ondetailed i
how to your deviceconfigure and explore .
Device Settings
STEP 5
Thank you for choosing DEVA!
Upon entering the device's settings, you will be able to apply the needed adjustments to the DB9009-RX.
In order the applied settings to be used press the [Save] button, placed on the bottom right part of each
screen.
For further information on the available options and features, which can beplease refer to the User Manual
found on www.devabroadcast.com/downloads, and the accompanying CD.