dg casa 16650-Q User manual

OCEAN PLATFORM BED
ASSEMBLY INSTRUCTION
16650-Q

WARNING
Seller and Manufacturer disclaim all and any liability for
property damage, personal injury, or loss, direct, indirect, or
incidental, resulting from the incorrect assembly, inadequate
maintenance, improper use, or neglect of this product.
Request a replacement by logging into the marketplace
account in which the purchase was made and sending a
message to the seller. To assist in expediting the request
attach applicable images relevant to the request and/or
part number and quantity.
• Keep these assembly instructions for future reference.
• Do not use this product if there are missing parts,
damaged, or broken until repairs are made and/or factory
replacement parts are installed.
• Check all packing material carefully for small hardware
that may have become loose inside the carton
during shipment.
• Identify and count all hardware and parts to compare with
parts and hardware list.
• Follow assembly instructions closely. Improper assembly
can result in personal or property damage.
• Secure all bolts and screws before use.
• Every 90 days check all bolts and screws are secured.
• Some parts may have sharp corner or edges and may
be heavy.
• Do not use or store this product near open flames or
around flammable chemicals.
• When placing contents on non-carpeted flooring, it’s
recommended to use floor protection such as an area rug
or furniture pads. These are not included with the purchase.
NOTICE
REPLACEMENT PART OR HARDWARE REQUEST:
TOOLS REQUIRED:
ALLEN WRENCH
(PROVIDED)
PHILLIPS SCREWDRIVER
(NOT PROVIDED)
16650-Q

HARDWARE
T U
R S
ML N O
SUPPORT LEG ADJUSTER
5 PCS
SPRING WASHER
6 PCS
FLAT WASHER
8 PCS
M6 x 50
9 PCS
M6 x 60
4 PCS
SCREW
32MM
26 PCS
P Q
ALLEN KEY 70MM
1 PC
ALLEN KEY 100MM
1 PC
M8 x 20
8 PCS M6 x 30
8 PCS

OCEAN PLATFORM BED PARTS
A
B
C1
C2
D
E
F
G
H
I
HEADBOARD 1 PC
FOOTBOARD 1 PC
SIDE RAIL 2 PCS
SIDE RAIL 2 PCS
HEADBOARD LEGS 2 PCS
FOOTBOARD
SIDE LEG 2 PCS
SIDE RAIL
LEGS 2 PCS
SLAT 1 PC
CENTER RAIL
SLAT SUPPORT 2 PCS
SLAT 12 PCS
JSUPPORT LEGS 1 PC
KBIG SUPPORT LEGS 1 PC

STEP 2
STEP 1
STEP 3
ASSEMBLY INSTRUCTION
COMPONANTS AND HARDWARE TO BUILD THE BED IS LOCATED IN THE HEADBOARD.
UNZIP THE ZIPPER COMPARTMENT LOCATED AT THE BACK OF THE HEADBOARD TO
ACCESS THESE PARTS.
B
P
N
S
D
MATCH THE LABEL TO ENSURE THE HEADBOARD LEGS
ARE INSTALLED ONTO THE CORRECT SIDE OF THE HEADBOARD
E
N
P
D
A
ATTACH LEGS TO FOOTBOARD AND HEADBOARD AS SHOWN.
HEADBOARD BACK VIEW
HEADBOARD BACK VIEW
HEADBOARD FRONT VIEW
ATTACH PART L TO THE HEADBOARD AND FOOTBOARD BRACKETS AS SHOWN.
DO NOT TIGHTEN COMPLETELY. THE SIDE RAILS WILL BE ATTACHED TO THESE
TOWARDS THE END OF THE ASSEMBLY.
A
B
L
Q

STEP 4
STEP 5
ATTACH THE SIDE RAIL LEG (F) TO THE SIDE RAIL (C).
C2
C1
F
T
P
M
A
C
B
ATTACH THE ASSEMBLED SIDE RAIL (C) TO THE HEADBOARD (A) AND FOOTBOARD (B) BY
PUSHING THE BRACKETS DOWN TO FIT AND TIGHTEN ONCE BOTH SIDE RAIL ARE IN PLACE.

STEP 7
STEP 6
ATTACH THE BIG SUPPORT LEGS (K) TO THE SLATS (I).
ATTACH THE SUPPORT LEGS (J) TO THE SLATS (H) AND CENTER RAIL SLAT SUPPORT (G).
ROTATE PART U CLOCKWISE OR COUNTER CLOCKWISE TO ADJUST
SLAT HEIGHT FOR PROPER MATTRESS SUPPORT.
P
I
N
I
K
U
H
H
U
G
O
P
H
J
ROTATE PART U CLOCKWISE OR COUNTER CLOCKWISE TO ADJUST
SLAT HEIGHT FOR PROPER MATTRESS SUPPORT.

STEP 8 TIGHTEN PART (L) FROM STEP 3 TO SECURE THE SIDERAIL TOTHE HEADBOARD AND FOOTBOARD.
ATTACH THE SLATS TO THE WOODEN SUPPORT ON THE SIDE RAIL WITH PART (R).
ADJUST PART (U) FROM STEP 6 AND STEP 7 FOR PROPER MATRESS SUPPORT.
H
I
H
QR
x26