dg casa ARGO 12350-T User manual

ARGO STORAGE BED
ASSEMBLY INSTRUCTION
12350-T

WARNING
Seller and Manufacturer disclaim all and any liability for
property damage, personal injury, or loss, direct, indirect, or
incidental, resulting from the incorrect assembly, inadequate
maintenance, improper use, or neglect of this product.
Request a replacement by logging into the marketplace
account in which the purchase was made and sending a
message to the seller. To assist in expediting the request
attach applicable images relevant to the request and/or
part number and quantity.
• Keep these assembly instructions for future reference.
• Do not use this product if there are missing parts,
damaged, or broken until repairs are made and/or factory
replacement parts are installed.
• Check all packing material carefully for small hardware
that may have become loose inside the carton
during shipment.
• Identify and count all hardware and parts to compare with
parts and hardware list.
• Follow assembly instructions closely. Improper assembly
can result in personal or property damage.
• Secure all bolts and screws before use.
• Every 90 days check all bolts and screws are secured.
• Some parts may have sharp corner or edges and may
be heavy.
• Do not use or store this product near open flames or
around flammable chemicals.
• When placing contents on non-carpeted flooring, it’s
recommended to use floor protection such as an area rug
or furniture pads. These are not included with the purchase.
NOTICE
REPLACEMENT PART OR HARDWARE REQUEST:
TOOLS REQUIRED:
ALLEN WRENCH
(PROVIDED)
PHILLIPS SCREWDRIVER
(NOT PROVIDED)
HAMMER/MALLET
(NOT PROVIDED)
12350-T

HARDWARE
WOOD DOWEL
4 PCS
9
DRAWER STOPPER
4 PCS
10
SPRING WASHER
4 PCS
8
M6 x 50
8 PCS
1
SCREW
25MM
4 PCS
5
SCREW
32MM
26 PCS
6
SCREW
50MM
16 PCS
7
SCREW
16MM
32 PCS
4
CASTER
8 PCS
11
ALLEN KEY 70MM
1 PC
3
ALLEN KEY 100MM
1 PC
2
M8 x 20
8 PCS
12

ARGO STORAGE BED PARTS
A
B
C1
C2
D
E
F
G
H
I
(L)
(R)
M
N
O
HEADBOARD 1 PC
FOOTBOARD 1 PC
SIDE RAIL 2 PCS
SIDE RAIL 2 PCS
HEADBOARD LEG 2 PCS
FOOTBOARD
SIDE LEG 2 PCS
DRAWER FRONT PANEL 2 PCS
DRAWER BACK PANEL 2 PCS
DRAWER LEFT SIDE
PANEL 2 PCS
DRAWER RIGHT SIDE
PANEL 2 PCS
DRAWER BOTTOM
PANEL 2 PCS
DRAWER BOTTOM
PANEL BIG SUPPORT
WOOD 2 PCS
DRAWER BOTTOM
PANEL SMALL SUPPORT
WOOD 2 PCS
SLAT 3 PCS
SIDE RAIL SUPPORT LEG 2 PCS

FABRIC PANEL INDICATES
FRONT OF DRAWER
BOTTOM DRAWER VIEWSTEP 2STEP 1
7x8
IR
H
L
6
N
OH
N
x10
TAPPED HOLE INDICATES
BACK OF DRAWER
BOTTOM DRAWER VIEW
11
4
ALIGN CASTER MOUNTING
HOLE TO NOTCHES ON
PART O THEN INSTALL CASTER
x16
BOTTOM DRAWER VIEW
N
H
STEP 4STEP 3
ASSEMBLY INSTRUCTION
M
SLIDE PART N TOWARDS THE FRONT DRAWER

STEP 5
2
81
D
E1
2
AD
x6
*BACK OF HEADBOARD
B
STEP 6
9
C1
LIGHTLY TAP INTO PLACE
9
STEP 7 STEP 8
5
G
C1
12
2
B
A
ATTACH PART G BY ALIGNING PRECUT HOLES
LOCATED ON ONE SIDE OF THE PART TO PART 9,
THEN INSTALL PART GTO PART C1
9

STEP 9
STEP 10
C2
B
C1
A
C1 CAN BE ASSEMBLED ON THE LEFT OR RIGHT SIDE BASED ON YOUR PREFERENCE. EXAMPLE SHOWN ON REF.1
REF. 1
C1 INSTALLED ON
THE RIGHT SIDE
10
x4

STEP 11
6
F
3