dg casa 95450-DSK User manual

DESK WITH SOLID LEG
95450-DSK

MAX : 33 lbs
MAX : 6 lbs

IMPORTANT INFORMATION
Seller and Manufacturer disclaim all and any liability for
property damage, personal injury, or loss, direct, indirect, or
incidental, resulting from the incorrect assembly, inadequate
maintenance, improper use, or neglect of this product.
Request a replacement by logging into the marketplace
account in which the purchase was made and sending a
message to the seller. To assist in expediting the request
attach applicable images relevant to the request and/or
part number and quantity.
Keep these assembly instructions for future reference.
Do not use this product if there are missing, damaged,
or broken parts until repairs are made and/or factory
replacement parts are installed.
Check all packing material carefully for small hardware
that may have become loose inside the carton
during shipment.
Identify and count all hardware and parts to compare with
parts and hardware list.
Follow assembly instructions closely. Improper assembly
can result in personal or property damage.
Secure all bolts before use.
Every 90 days check all bolts are secured.
Some parts may have a sharp corner or edge and may
be heavy.
Do not use or store this product near open flames or
around flammable chemicals.
When placing contents on non-carpeted flooring, it’s
recommended to use floor protection such as an area rug
or furniture pads. These are not included with the purchase.
NOTICE
REPLACEMENT PART OR HARDWARE REQUEST:

HARDWARE & TOOL PARTS
HARDWARE REQUIRED:
TOOLS REQUIRED:
HEX WRENCH PH1 SCREW DRIVER
(PROVIDED)
MINIFIX X 17 PCS
UNITAR SCREW (6.3 X 40)
X 3 PCS
CSK SCREW (3.5 X 15)
X 4 PCS
CSK SCREW (4 X 32)
X 1 PCS
CAM 12/15 X 17
PCS
WOOD DOWEL (O8 X 30)
X 26 PCS
(PROVIDED)
1
4
METAL SUPPORT (19 X 1186)
X 1 PCS
7
6
5
23

A........Solidwood leg..........x 1
........Solidwood leg..........x 1
B
C
D........Top Panel................x 1
..............x 1........Back Panel
E........Upper Top Panel.....x 1
F ........Bottom Support.......x 1
G........Partition Panel.........x 2
DESK WITH SOLIDWOOD LEG ASSEMBLY PARTS
A
B
D
E
G
G
C
F

Insert all wood dowel in each panel as shown.
Note: Make sure all the dowel are insert into all panel without missing any hole.
x 26
Wood Dowel (O8x30mm)
3
X2
DESK WITH SOLIDWOOD LEG - STEP 1
B
A
D
F
E
G

Insert Minifix on each panel and then use a screw driver to tighten up all.
Note: Do not over tighten the Minifix it will cause issues when assemble all panel.
x 17
Minifix
1
D
A
D
B
E
C
DESK WITH SOLIDWOOD LEG - STEP 2

Attach Upper Top panel E to Partition panel G and insert Cam (12/15) on each side of the
Panel G and tighten it with screw driver.
Note: Make sure to refer the picture were shown how to position the Cam correctly.
x 2
Cam (12/15)
2
EG
G
DESK WITH SOLIDWOOD LEG - STEP 3

x 2
Cam (12/15)
2
Attach Panel E and G to Top panel D and insert Cam (12/15) then use a screw driver
to tighten it.
Note: Make sure to refer the picture were shown how to position the Cam correctly.
E
G
G
D
DESK WITH SOLIDWOOD LEG - STEP 4

FD
x 1
Cam (12/15)
2
Attach Bottom Support F to Top panel D and insert Cam (12/15) then use a screw driver
to tighten it.
Note: Make sure to refer the picture were shown how to position the Cam correctly.
DESK WITH SOLIDWOOD LEG - STEP 5

x 5
Cam (12/15)
2
Attach Solidwood leg B to Panel D,E and F and insert Cam (12/15) then use a screw driver
to tighten it.
Note: Make sure to refer the picture were shown how to position the Cam correctly.
D
E
F
B
DESK WITH SOLIDWOOD LEG - STEP 6

x 5
Cam (12/15)
2
Attach Solidwood leg A to Panel D,E and F and insert Cam (12/15) then use a screw driver
to tighten it.
Note: Make sure to refer the picture were shown how to position the Cam correctly.
D
F
E
A
DESK WITH SOLIDWOOD LEG - STEP 7

Attached the Metal support and insert Csk screw (3.5 X 15) to Panel A and B then tighten it
using ph1 screwdriver, then insert Csk screw (4 X 32) and tighten it using screwdriver to
panel D.
IMPORTANT: Fully tighten all Csk screw on that panel.
x 1
Csk Screw (M4 X 32)
5
x 4
Csk Screw (M3.5 X 15)
4
x 1
Metal Support(19X1186)
7
D
A
B
DESK WITH SOLIDWOOD LEG - STEP 8

x2
Cam (12/15)
2
Attach Back panel C to the back side and insert Cam (12/15) to Panel A and B then
then tighten it with screw driver.
Note: Make sure to refer the picture were shown how to position the Cam correctly.
A
B
C
DESK WITH SOLIDWOOD LEG - STEP 9

Insert the Unitar screw on Back panel C and then tighten it with a Hex wrench.
Note: Make sure do not over tighten the unitar screw.
x 3
Unitar Screw (6.3 X 40)
6
C
DESK WITH SOLIDWOOD LEG - STEP 10

Enjoy your new Desk With Solidwood Leg!
ASSEMBLY COMPLETE