dg casa HUTCH DESK User manual

HUTCH DESK WITH METAL LEG
95500-DSK

MAX : 11 lbs
MAX : 66 lbs

IMPORTANT INFORMATION
Seller and Manufacturer disclaim all and any liability for
property damage, personal injury, or loss, direct, indirect, or
incidental, resulting from the incorrect assembly, inadequate
maintenance, improper use, or neglect of this product.
Request a replacement by logging into the marketplace
account in which the purchase was made and sending a
message to the seller. To assist in expediting the request
attach applicable images relevant to the request and/or
part number and quantity.
Keep these assembly instructions for future reference.
Do not use this product if there are missing, damaged,
or broken parts until repairs are made and/or factory
replacement parts are installed.
Check all packing material carefully for small hardware
that may have become loose inside the carton
during shipment.
Identify and count all hardware and parts to compare with
parts and hardware list.
Follow assembly instructions closely. Improper assembly
can result in personal or property damage.
Secure all bolts before use.
Every 90 days check all bolts are secured.
Some parts may have a sharp corner or edge and may
be heavy.
Do not use or store this product near open flames or
around flammable chemicals.
When placing contents on non-carpeted flooring, it’s
recommended to use floor protection such as an area rug
or furniture pads. These are not included with the purchase.
NOTICE
REPLACEMENT PART OR HARDWARE REQUEST:

HARDWARE & TOOL PARTS
HARDWARE REQUIRED:
TOOLS REQUIRED:
HEX WRENCH PH1 SCREW DRIVER
(PROVIDED)
MINIFIX X 20 PCS
EURO SCREW (6X9)
UNITAR SCREW (6.3 X 40)
X 12 PCS
X 8 PCS
DRAWER SLIDE (350MM)
X 2 SETS
CSK SCREW (3.5 X 15)
X 20 PCS
CSK SCREW (M4.7 X 38)
X 20 PCS
CAM 12/15 X 20
PCS
WOOD DOWEL (O6 X 30)
X 34 PCS
(PROVIDED)
(R)
(R)
(L)
(L)
1
6
4
7
5
METAL LEG (L-675MM)
X 4 PCS
9
8
23

A........Side Panel...............x 1
B.........Side Panel...............x 1
C
D........Partition Panel.........x 1
.........x 1........Partition Panel
E........Top Panel................x 1
F ........Bottom Panel...........x 1
G........Side Top (L)............x 1
............x 1........Side Top (R)H
I ........Top Back Panel.......x 1
J........Top Shelf
.......Support Panel
..................x 1
K ...........x 1
L ........Drawer Front (L)......x 1
M........Drawer Front (R).....x 1
N
O
P........Drawer Back ...........x 2
........Drawer Side (L).......x 2
........Drawer Side (R).......x 2
Y..........Backply...................x 1
Z.........Drawer Bottom........x 2
HUTCH DESK WITH METAL LEG ASSEMBLY PARTS
E
H
K
IJ
G
Y
F
A
C
D
B
Z
Z
M
L
P
N
O
P
N
O

Insert all wood dowel in each panel as shown.
Note: Make sure all the dowel are insert into all panel without missing any hole.
x 34
Wood Dowel (O6x30mm)
3
X2
X2
HUTCH DESK WITH METAL LEG - STEP 1
H
G
K
I
B
D
C
A
O
N
J

Insert Minifix on each panel and then use a screw driver to tighten up all.
Note: Do not over tighten the Minifix it will cause issues when assemble all panel.
x 20
Minifix
1
HUTCH DESK WITH METAL LEG - STEP 2
H
G
E
M
L

HUTCH DESK WITH METAL LEG - STEP 3
Attached drawer slide on Side panel A and B also Partition panel C and D then insert
Euro screw and tighten using a screw driver.
Note: Make sure to insert the euro screw into the right hole so the drawer slide
is in correct position.
Euro Screw (6 x 9)
x 8 x 2 SETS
FDrawer Slide (350mm) 86
(R)
(L)
(L)
(R)
B
A
C
D
(L)
(R)

Attached drawer side N to drawer back P and use Csk screw and tighten it with a screw
driver and repeat for drawer side O.
IMPORTANT: Fully tighten all Csk screw on all 2 drawer.
x 8
Csk Screw (M4.7 X 38)
5
X2
HUTCH DESK WITH METAL LEG - STEP 4
P
O
N

X2
Insert the Drawer bottom Z between Drawer side N and O.
IMPORTANT : Make sure Drawer bottom Z were inserted onto drawer
back for all 2 drawer.
HUTCH DESK WITH METAL LEG - STEP 5
Z
N
O

Attach Drawer Front L & M on the drawer and insert Cam (12/15) on each side of the
drawer side and tighten it with screw driver.
Note: Make sure to refer the picture were shown how to position the Cam correctly.
X2
HUTCH DESK WITH METAL LEG - STEP 6
x 4
Cam (12/15)
2
L
M

Attach Drawer slide (350mm) and then use ph1 screw driver to tighten Csk screw
(3.5 X 15).
Note: Repeat the same step for all 2 drawer and make sure to put the drawer slide
in the right position.
Csk Screw (3.5 X 15)
x 8 x 2 Sets
Drawer Slide (350mm)
84
(R)
(L)
X2
O
HUTCH DESK WITH METAL LEG - STEP 7
(L) (R)

HUTCH DESK WITH METAL LEG - STEP 8
x 4
Csk Screw (M4.7 X 38)
5
Attached the Top shelf J to Top back panel I and Insert Csk screw and tighten it with a
screw driver.
IMPORTANT: Fully tighten all Csk screw on that panel.
J
I

G
J
H
HUTCH DESK WITH METAL LEG - STEP 9
x 4
Cam (12/15)
2
Attach Side Top G and H to Top shelf J and insert Cam (12/15) then use a screw driver
to tighten it.
Note: Make sure to refer the picture were shown how to position the Cam correctly.

K
J
Attach Support panel K to Top shelf J.
Note: Make sure to attach panel K on to Panel J correctly.
HUTCH DESK WITH METAL LEG - STEP 10

HUTCH DESK WITH METAL LEG - STEP 11
Attached panel G,H,I,J and K that already assemble to Top panel E and insert Csk screw
then tighten it with a screw driver.
IMPORTANT: Fully tighten all Csk screw on that panel.
x 8
Csk Screw (M4.7 X 38)
5
E
G
J

E
HUTCH DESK WITH METAL LEG - STEP 12
x12
Cam (12/15)
2
Attach Side panel A,B and Partition panel C and D to Top panel E and insert Cam (12/15)
on each panel then tighten it with screw driver.
Note: Make sure to refer the picture were shown how to position the Cam correctly.
A
C
D
B

Insert the Backply Y on back side of the panel as shown.
Note: Make sure to put the backply according to the groove at the back side.
HUTCH DESK WITH METAL LEG - STEP 13
Y

HUTCH DESK WITH METAL LEG - STEP 14
Attach Bottom panel F to the other panel that already assemble, then insert Unitar screw
and tighten it with a Hex wrench.
Note: Make sure do not over tighten the unitar screw.
x 12
Unitar Screw (6.3 X 40)
7
F

HUTCH DESK WITH METAL LEG - STEP 15
Attach the Metal leg to Bottom panel F and insert Csk screw (3.5 x 15) then tighten it with
a screw driver.
Note: Make sure to tighten all csk screw.
Csk Screw (3.5 X 15)
x 12
4Metal Leg (L-675mm)
x 4
9
F