Digital Watchdog VMAX A1 G4 DW-VA1G44 User manual

Quick Start Guide
Tel: [phone]
Technical Support Hours: 9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
Attention: This document is intended to serve as a quick reference for initial setup. It is
recommended that the user read the entire instruction manual for complete and proper installation
and usage.
4-Channel 8-Channel 16-Channel
DW-VA1G44 DW-VA1G48 DW-VA1G416
DW-VA1G442T DW-VA1G482T DW-VA1G4162T
DW-VA1G444T DW-VA1G 484T DW-VA1G41 64T
DW-VA1G446T DW-VA1G486T DW-VA1G4166T
DW-VA1G448T DW-VA1G488T DW-VA1G4168T
DW-VA1G441 0T DW-VA1G4810T DW-VA1G41610T
DW-VA1G4412T DW-VA1G4812T DW-VA1G41612T
DW-VA1G441 6T DW-VA1G4816T DW-VA1G41616T
DW-VA1G4820T DW-VA1G41620T
DW-VA1G4832T DW-VA1G41632T
Quick Start Guide
1. Mount and install all necessary cameras and external devices. Refer to their individual
manuals for additional information.
2. The DVR supports the following analog signals:
• HD-Analog
• HD-TVI
• Standard analog signal up to 960H
The DVR supports cameras up to 5MP (4K for 8/16CH models). Refer to the product’s data
sheet and full manual for recording specifications per product.
3. The DVR supports automatic signal detection. This means the DVR will detect the proper
signal automatically.
4. Place the DVR in its final position. See safety tips below.
5. Connect all necessary cables to the DVR.
6. Connect the DVR to an appropriate power supply.
The DVR will boot up automatically.
1. Make sure the cameras and the monitors are properly connected to the DVR.
2. The DVR should be placed in a dust and moisture free environment. It must never
be directly exposed to sunlight. A room temperature is highly recommended to reduce
the chance of overheating, (room temperature is considered as 68~78°F), which may
cause the DVR to become unstable.
3. During the boot up process, the DVR should not be interrupted by pressing any
buttons on the mouse. Do not unplug the power adapter or turn the DVR o during the
boot up process.
4. A UPS (uninterrupted power supply) is highly recommended to prevent damage to the
DVR during a power outage.
STEP 1 – CONNECTING THE DVR
SAFETY TIPS
NOTE: HD Monitor output and VGA output cannot be used at the same time for dual monitoring.
To prevent the DVR from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of 104°F (40°C). To prevent airflow restriction, allow
at least 3 inches (7.6 cm) of clearance around the ventilation openings.
Model Power consumption
DW-VA1G44 DC12V, 24W, 2A
DW-VA1G48 DC12V, 48W, 4A
DW-VA1G416 DC12V, 48W, 4A
WHAT’S IN THE BOX
Quick start guide
and download card 1 set
DC 12V adapter and
power cable
(*4-channel models do
not come with power
cable)
1 set
USB mouse 1 Rubber mounts – 4pcs 1 set
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the ‘Search by Product’ search bar.
Results will populate automatically based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals and quick start guide (QSGs)
will appear in the results.
When the DVR boots up, it will be in protective mode
and the password setup screen will appear.
1. Setup a new password. The password must be a
minimum of eight (8) characters with at least four
(4) combinations of uppercase letters, lower-case
letters, numbers, and special characters.
2. When the DVR boots up for the first time, you will be
guided through the startup wizard.
STEP 2 – POWERING UP THE DVR
When logging into the DVR for the first time, you will be prompted to set up a new password. The new
password must include a minimum 8 characters with at least four combinations of uppercase and lowercase
letters, numbers, and special characters.

1. Follow the startup wizard’s instructions to setup the DVR’s basic settings. You may not
need to change any default settings to properly set up your system. At any time, you
can skip steps, go back, or exit the wizard and setup the DVR manually.
2. Set the DVR’s network settings to match your network’s requirements. It is
recommended to set the network type to “AUTO CONN.” and let the DVR auto-detect
the network’s settings. Then, change the type
to static. Contact your network administrator
for additional information.
Press “APPLY” to save and “NEXT” to move to
the next step.
Adjust the DDNS or PathFinder™ option.
See STEP 6 - MOBILE APP REMOTE
MONITORING.
To add a UTC or PTZ camera:
1. Right-click anywhere on the screen
and go to “MENU” > “DEVICE” > “PTZ”
2. Camera type will be auto-detected and displayed
under the camera tab. Protocol should match the
camera type detected.
• HD-A(C) -> legacy HD-Analog signal type camera.
• HD-A/HD-TVI -> HD-Analog signal type camera.
• HD-TVI-> HD-TVI signal type camera
(DW default signal type).
3. To control the camera’s menu and settings, press the
“PROGRAM” button under the “CONTROL”. See user
manual for more information.
1. Navigation – use the included USB mouse to navigate around the DVR’s monitoring and
Setup pages.
a. To access the menu bar – move the mouse’s cursor
to the bottom of the display area to show the menu
bar. You can also display it constantly by pressing
the pin icon on the right side.
b. To access the quick menu options, right-click
anywhere on the screen. This will take you to the quick menu
options, which include:
• “DISPLAY MODE” Options
• “DIGITAL ZOOM”, “PTZ” control and “FREEZE” image
(on supported cameras)
• “ADD BOOKMARK” video
• Instant “PLAYBACK”, “SEARCH” and “THUMBNAIL SEARCH”
• Recording status and analysis system monitoring
• Access to the “HEALTH CHECK” and open the main “MENU”.
2. Help – The help button located at the bottom left of setup screens
includes basic information and explanation of the features and
settings in that page, for on-the-go information.
Quick Start Guide
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
STEP 3 – STARTUP WIZARD
STEP 4 – UTC AND PTZ CAMERA CONTROL
STEP 6 – MOBILE APP REMOTE MONITORING
You can monitor your system from DW’s Mobile Plus™ app with a simple scan of a QR code.
1. Right-click anywhere on the DVR’s screen and
go to “MENU” > “NETWORK” > “PATHFINDER™”
2. Check the box next to ‘USE PATHFINDER’. Click
Save.
3. A mobile access QR code will appear on the
right side of the screen. Status at the bottom of
the screen should say “PATHFINDER™ SERVICE
ACTIVATED”.
To view the DVR on your mobile app:
1. Download the latest DW Mobile Plus™ app from
the Google Play Store or Apple App store.
2. Launch the DW Mobile Plus™ application on
your device.
3. Go to the Site menu to register a new site with
the QR code scan.
4. Press QR icon next to the Host field.
5. Capture the QR code in the DVR’s PathFinder
settings page. The camera will capture the QR
code automatically once all four corners of
the code are registered in the camera’s frame
properly.
6. The IP address field will show the DVR’s MAC
address information.
7. Complete the new device’s registration
information by adding the device name, port
number, user-name and password. Select
“SAVE” to complete the registration.
8. The new site will appear in your sites list.
Rev: 09/22
STEP 5 – MONITOR YOUR SYSTEM
EXISTING COAX CABLE
COAX CABLE
CAMERA
CAMERA
CAMERA
DVR
OSD
CAMERA SETTINGS
EXPOSURE
COLOR
DAY/ N IG H T
MOTION
The DVR supports complete camera
control via the coaxial connection (UTC).
There is no need for an additional RS485
connection to control the camera. This
feature must also be supported on the
camera’s side.
NOTE: If you are connecting a camera via UTC protocol,
baudrate and address settings will be disabled.