Quick Start Guide Quick Start Guide
WHAT’S IN THE BOX
Hexagonal
wrench 1Mounting
template 1
DC plug
cable 1
Screws and
plastic anchors
- 4pcs
1 set
Test video
cable 1
Moisture
absorber and
absorber guide
(recommended)
1
Star wrench
drive 1Quick set up
guide 1
1. The mounting surface must withstand five times the camera weight.
2. Pay attention to the cables. The can easily become caught and damaged.
Any damage may cause a short or fire.
3. Install the moisture absorber in the base of the camera’s lens.
a. Remove the moisture absorber from the packaging.
b. Place the moisture absorber around the base of the camera’s lens module.
Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
Power Requirements Power Consumption
DC12V/AC24V dual voltage
DC12V (LED o): 3.0W
DC12V (LED on): 5.2W
AC24V (LED o): 2.3W
AC24V (LED on): 4.6W
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
DWC-V4283WTIR DWC-V4283WD
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Attention: This document is intended to serve as a quick reference for initial
setup. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources.
2. Search your product by entering the part number in
the ‘Search by Product’ search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
DW® Universal HD over Coax® Snapit™
vandal dome cameras
Protective film
Protective sheet
Please attach the card type absorber to
attachment point as the picture.
Absorber attachment point
4. Detach the camera’s dome cover by loosening the screws on each side of the
dome.
5. Using the mounting template sheet or the camera itself, mark and drill the
necessary holes in the wall or ceiling.
WARNING: It is highly recommended that you install the moisture
absorber when mounting the camera. The moisture
absorber prevents moisture from being captured
inside the camera's housing, which may cause image
performance issues and damage the camera.
NOTE: The camera will generate enough heat to dry moisture
during operation. In most cases it will not need the
moisture absorber for more than the first day. In cases
where the camera can experience a moisture issue,
users must keep the moisture absorber in the camera.
The moisture absorber has an approximately 6-month
life cycle, varying depending on the environment.
