Digital Watchdog NightWatch DW-ILWM2 User manual
Double wall–mount bracket for LED illuminators
DW-ILWM2
Attention: This document is intended to serve as a quick reference for initial setup.
It is recommended that the user read the entire instruction manual for complete and proper installation and usage.
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources.
2. Search for your product by entering the part number in the ‘Search by Product’ search bar. Results
for applicable part numbers will populate automatically based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals and quick start guide (QSGs) will
appear in the results.
Quick Start Guide
WHAT’S IN THE BOX
1x double mount bracket
1x 3 way tee box
2x M3 x 0.62” (16mm) screw
4x M6 serrated flanged nut
4x M6 x 0.47” (12mm) bolt
1x quick setup guide
QuickStart
Guide
1
2
3
4
QuickStart
Guide
1
2
3
4
QuickStart
Guide
1
2
3
4
Rev Date: 08/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Quick Start Guide
INSTALLING THE MOUNT BRACKET
Attach the wall mount bracket to the structure using suitable tapping screws (PLASTIC ANCHOR, PTS1
M8x40L) as illustrated in figure 1 below. The wall bracket must be attached to a structure such as hardwood,
wall stud, concrete or a suitable material capable of supporting the final mount assembly. You may need to
change the method of mounting or hardware used depending on the wall material.
LED ILLUMINATOR INSTALLATION WITH DOUBLE WALL MOUNT BRACKET
1 2
3
Use the bracket to mark and drill the necessary holes in the wall.
With the bracket secured to the wall, attach the illuminators with the supplied M6 nuts and bolts. For each
illuminator, attach the center bolt first then rotate the illuminators to the required horizontal position. Once
the necessary position is achieved, secure the illuminators with the remaining nut and bolt in one of the
outer holes.
Vertical adjustment can be made via the two hex bolts on each side of the illuminator.
A waterproof junction box is attached to the bracket’s rear plate. This allows for a single power cable to be
routed to the junction box and then split to each illuminator. This can be removed if not required.
NOTE: Recommended fasteners:
• Head size: minimum 0.6”
• Screw or bolt diameter: maximum 0.5”
• Fastener strength: minimum 6 lb.
Table of contents
Other Digital Watchdog TV Mount manuals
Digital Watchdog
Digital Watchdog DWC-P336CNMW User manual
Digital Watchdog
Digital Watchdog DWC-MTTWM User manual
Digital Watchdog
Digital Watchdog NightWatch DW-ILWM1 User manual
Digital Watchdog
Digital Watchdog DWC-PV20WMW User manual
Digital Watchdog
Digital Watchdog SiteWatch DW-DTWMDTLA5 User manual
Digital Watchdog
Digital Watchdog DWC-PZWM User manual
Digital Watchdog
Digital Watchdog DWC-V7CMW User manual
Digital Watchdog
Digital Watchdog DWC-PMB-WLW User manual
Digital Watchdog
Digital Watchdog DWC-P336PARAMW User manual
Digital Watchdog
Digital Watchdog DWC-MTTWM2 User manual
Digital Watchdog
Digital Watchdog DWC-P220CMW User manual
Digital Watchdog
Digital Watchdog NightWatch DW-ILWM3 User manual
Digital Watchdog
Digital Watchdog DWC-PV20CMW User manual
Digital Watchdog
Digital Watchdog NightWatch DW-ILWM3 User manual
Digital Watchdog
Digital Watchdog DWC-V1WMW User manual
Digital Watchdog
Digital Watchdog DWC-V1CNMW User manual
Digital Watchdog
Digital Watchdog DWC-P336WMW User manual
