Digitus DN-80120 User manual

4-Port Gigabit Network Switch,
1 SFP Uplink
Quick Installation Guide
DN-80120

2
1. Product Introduction
DIGITUS® 4-Port Gigabit Network Switch, 1 SFP Uplink.
The product provides high-speed packet forwarding capability and
ample backplane bandwidth to ensure clear and smooth image
transmission. It is embedded in static electricity and surge
protection circuit to improve product stability. It also supports VLAN
configuration mode, which enables network storm suppression,
protects security information, and prevents the spread of viruses
and network attacks. It fully meets the requirements of network
video surveillance system.
2. Product Feature
1. 4-port 10/100/1000 Mbps RJ45 LAN port
2. 1-port 1000Mbps fiber port (SFP slot)
3. VLAN configuration by DIP switch
4. Long distance mode support distance of 330m
at 10Base-T data rate.
5. VLAN configuration: Port Isolation & 1 to 1 Isolation
6. Full power range 100~240V AC
7. IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z
8. Provide wall-mount bracket
3. Package Content
Network switch

Wall mount bracket

Power cord
QIG

3
4. Specifications
Power part
Power supply
AC
Adapt to the
voltage range
AC 100 ~ 240V
Power
consumption
<10W
Port
parameters
Ports
1~4 Electrical interface:
10/100/1000 Mbps
Fiber interface: 1000 Mbps
Transmission
distance
Electrical interface :
Normal mode, 0-100m
Long-distance mode,0-330m
Fiber interface: 20km
Switching
Specification
Network
standards
IEEE802.3/802.3u/802.3z/802.3ab
Packet cache
512 Kbits (5 ports switch)
1 Mbits (9 ports switch)
MAC-Address
capacity
1K
Status
indicator
Power LED
1(green)
SPD LED
L/A LED
SPD: On is 100M(1000M),
Off is 10M(10/100M)
L/A: On is Link
Off is Down, Flash is Act
Fiber LED
1(green)
Environmental
Limits
Operating
Temperature
-20 °C ~ 60 °C
Storage
Temperature
-40 °C ~ 85 °C
Ambient
Relative
Humidity
5-95%

4
Physical
Characteristics
Dimensions
109mm×125mm×32mm
(5 Port Switch)
Housing
Aluminum shell, IP30 protection
Color
black
Weight
0.43kg (5 Port Switch)
Installation
DIN-rail mounting, wall mounting
(with optional kit)
Reliability
MTBF
≥500000h
5. Product Overview
1
DIP Switcher
6
Fiber Link LED
2
Power LED
7
SFP Uplink Port
3
Electric port Link LED
8
RJ-45 Port
4
Electric port rate LED
9
AC Power connector
5
Electric port number

5
5.1 Product Diagram
1
Broadband Router
6
Home Cinema
2
Wireless Access Point
7
IPTV
3
Laptop
8
Game Player
4
VoIP Phone
Network cable
5
IP Camera
Fiber cable
5.2 LED Indicator
LED
status
Description
PWR
on
Power Operating normally
off
PWR is not connected or is not
operating properly
Link
on
Port link UP
flash
Port forwarding data
off
Port link DOWN or not connect
10/100/1000
Base-T
(Gigabit switch)
on
1000Base-T
off 10/100Base-T

6
5.3 DIP switch
The switch defaults to the standard network mode at the factory,
and the dial keys ①and ②are in the off position. After the device
is power on, all of ports are interoperable.
One-to-one isolation: Dial key ①to on position, dial key ②
default off position. After the device is power on, it starts the one-
to-one isolation mode configuration and implements the
corresponding ports of the two ports. In this case, the ports on the
same device cannot be forwarded to each other. They can only
communicate with the corresponding port on the peer device.
Port Isolation: Dial key ②to on position, Dial key ①default off
position. After the device is power on, port isolation is achieved. The
RJ45 ports cannot communicate with each other, the
communication takes place between the SFP port and the individual
RJ45 ports.
Long distance mode: Dial key ①and ②to on position. After the
device is power on, the long-distance mode configuration is enabled
and the electrical port rate is 10Base-T. The transmission distance of
the electrical port is increased. At this time the device port
transmission distance of 0-330 meters.
Notes
1 to 1 isolation mode must require two identical
switches, through the optical port docking network can
be used.

7
6. Important function
6.1 Port Isolation
The switch cannot carry out data transfer between each other, only
to the optical port to communicate, so the data conversion more
efficient, the system is running more secure.
6.2 One-to-one Isolation
When two switches A and B are connected through the optical
interface, the A switch port 1 can only communicate with the B
switch port 1. Similarly, A switch port 2 can only communicate with
B switch port 2, and so on. To establish one-to-one isolation mode
between A and B switches’ RJ45 ports, it requires 2pcs of same
switch. It prevents the network storm, eliminating the paralysis of
the system.

8
6.3 Long distance mode
By default, the switch electrical port transmission distance of 0-100
meters, open long distance mode, the electrical port for 10Mbit/s,
to meet the high-definition video transmission bandwidth while
increasing the maximum transmission distance of 330 meters. Thus
enabling the ability to install IP cameras at the front of the field.
7. Installation
7.1 Precautions
When placing the switch, please pay attention to stability, drop will
cause serious consequences.
Should be in the correct power supply to work properly, please
confirm before using the power supply and switch the power
requirements specified in line.
To reduce the risk of electric shock, do not open the case when the
switch is working, even if it is not charged, do not open it yourself.
When the switch works, the network cable can be inserted or pulled
out at the port without interrupting the work of the switch.
Before cleaning the switch, pull the switch's power plug first, wipe it
with a moisturizing fabric, and do not use liquid cleaning.
Do not place the switch in a watery or humid place and prevent
water and moisture from entering the switch housing.
When placing the switch, please avoid dusty and strong areas of
electromagnetic interference
7.2 Install style
There are two install methods that can be installed on the desktop
and wall mounted.
Notes
This product does not contain other fixed accessories
other than fixed mounting screws;
When installing or moving, please unplug the power cord.

9
7.2.1 Install to the desktop
You can place this product directly on a clean, solid, grounded desk.
7.2.2 Wall mounted
You can also place this product on a clean, solid vertical wall. The
installation process is as follows:
1. Fix the mounting brackets with screws
2. Insert the capsules into the holes on the wall. (The capsules are not
included in the package.)
3. Insert the screw into the hole of the dowel. Please use screws with
a diameter of 3-5 mm. Fix the network switch with the screws.
8. Connect the cable
1) Before installation, please turn off the power of each signal
source and the device to be displayed. The installation of the
power supply may cause damage to the transmission equipment.
2) Use the network cable to connect the network camera and
the 1-4 Electrical port of the device respectively;
3) Connecting the optical fiber interface of the device with the
optical fiber interface of the uplink equipment using the optical
fiber line.
4) To connect the power supply equipment.
5) Check whether the installation is correct, equipment damage, to
ensure that all connections are reliable, to the system power.
6) To confirm whether the network equipment, power supply,
work is normal.

10
9. Appendix - Port Properties
9.1 Electrical port properties
Interface Type
RJ45
Speed
10/100/1000Mbps (Gigabit switch)
Duplex mode
Half-duplex, full-duplex, adaptive
Cable standard MDI/MDI-X
Support standards
IEEE 802.3/802.3u
Cable type
10Base-T: 3/4/5 twisted pair, supports a
maximum transmission distance of 300m
100/1000Base-TX: 5/6 twisted pair,
supports a maximum transmission
distance of 100m
9.2 Fiber port properties
Interface Type
SFP slot
Speed
1000Mbits (Gigabit switch)
Duplex mode
Full-duplex
Support standards
IEEE802.3u, IEEE802.3z
Media and
transmission
distance
50/125um multimode fiber, supports
550m transmission distance
62.5/125um multimode fiber, supports
270m transmission distance
9/125um single-mode fiber, supports
1-120km transmission distance