Digitus DN-95342-1 User manual

16/24FE (PoE) + 2G Combo
PoE Switch
User Manual
DN-95342-1 Rev.2  DN-95343 Rev.3

Introduction
The DIGITUS® Combo PoE Switch are Gigabit Uplink Unmanaged Switch which
provides you with a high-performance, low-cost, easy-to-use, seamless and standard
upgrade to boost your old network to 1000Mbps. Increase the speed of your network
server and backbone connections, making Gigabit connection to a server or uplinking
a network necessarily.
Its PoE ports can automatically detect and supply power with those IEEE 802.3af/at
compliant Powered Devices (PD). The electrical power is transmitted along with data
in one single cable allowing you to expand your network where there are no power
lines or outlets, where you wish to fix devices such as AP, IP Cameras or IP Phones, etc.
Features
16 or 24 port 10/100Mbps PoE RJ45 Ports
2 x 10/100/1000Mbps Combo Ports
Complies with IEEE802.3af/at Power over Ethernet
Supports PoE Power up to 32W for each PoE port
Auto detect power device
Remote power and Data feeding up to 100m
Flow Control for Full Duplex operation and back pressure for Half Duplex
Operation
Support VLAN and CCTV function
8K MAC address, automatic address learning and address aging
Support Energy-Efficient Ethernet (EEE) function EEE802.3az
Support PD Alive function at CCTV mode (the switch port is disconnected
will automatically connected)

Package Contents
Check the following contents of your package:
 PoE Switch x1
 Manual x 1
 Power Cord x 1
 Accessories (Mounting Ears x2, Rubber Feet x4, screw x8)
If any part is lost and damaged, please contact your local agent immediately.
Hardware Description
Front Panel
The Front Panel Consists of DIGITUS 10/100M Auto-Negotiation Ethernet RJ45 Ports,
2-Port Gigabit Combo Port. The LED indicators are also shown on the panel.
DN-95343
DN-95342-1
Port Status indicator
Port Status indicator
16*10/100
Mbps PoE
Port
2*10/100/100
0 Mbps Port
2*1000 Mbps
share SFP slot
2*10/100/100
0Mbps Port
2*1000Mbps
share SFP
slot
24*10/100
Mbps PoE
Port
Port Status indicator

LED indicator
LED
Color
Function
PWR Green Off: No Power supply
Light: Indicates the switch has power
LNK/ACT Green
Off: No device is connected to the corresponding port
Light: Indicates the link through that port is successfully
established at 10/100/1000Mbps.
Blink: Indicates that the Switch is actively sending or
receiving data over that port.
Speed Green
Off: Indicates the link through established at
10/100Mbps.
Light: Indicates the link through established at 1000Mbps.
PoE Orange
Off: No PoE powered device (PD) connected
Light: There is a PoE PD connected to be port,
which supply power successfully.
Blink: Indicates port abnormal power supply
DIP Switch:
The DIP switch is located on the left panel.
Default: The factory default mode, can normal communication between
port 1~26.
VLAN:1-24 port can be isolated each other but 1-24 port can connect to
25T/S~26 T/S port after open VLAN to stop broadcast storm to
increase forwarding rate of frame.
CCTV:Up to 250m PoE distance allows you to expand you network via
Ethernet cable but where you want to fix device such as IP
Cameras.
Note:After change the mode, in order to the corresponding
configuration take effect. The switch needs to restart manually.

Rear Panel
The rear panel of DIGITUS Combo PoE Switch indicates an AC inlet power socket,
Grounding Column.
Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it.
Please follow the following instructions in avoid of incorrect installation causing device
damage and security threat.
Before cleaning the switch, unplug the power plug of the switch first. Do not
clean the switch with wet cloth or liquid.
Do not place the switch near water or any damp area. Prevent water or
moisture from entering the switch chassis.
Do not place the switch on an unstable case or desk. The switch might be
damaged severely in case of a fall.
Ensure proper ventilation of the equipment room and keep the ventilation
vents of the switch free of obstruction.
Make sure that the operating voltage is the same one labeled on the switch.
Do not open the chassis while the switch is operating or when electrical
hazards are present to avoid electrical shocks.
Power Socket
Grounding Column

Desktop Installation
Install the Switch on a desktop, please attach these cushioning rubber feet provided
on the bottom at each corner of the Switch in case of the external vibration. Allow
adequate space for ventilation between the device and the objects around it. The
installation diagram is as follows:
(Example: DN-95343 Rev.2)
Rack-mountable Installation
The switch is rack-mountable and can be installed on an EIA-19 inch equipment rack.
To do this, first, please install the mounting brackets on the switch’s side panels (one
on each side), secure them with the included screws, and then use the screws
provided with the equipment rack to mount the switch on the 19 inch rack.

(Example: DN-95343 Rev.2)
Turn on the switch
Plug in the negative connector of the provided power cord into the power socket of
the device, and the positive connector into a power outlet. After the device is powered
on, it begins the Power-On Self-Test. The PWR LED indicator will light on all the time.
Specifications
Model
DN-95342-1 Rev.2
DN-95343 Rev.2
Description
16FE (PoE) + 2G Combo
24FE (PoE) + 2G Combo
Standard IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z,
IEEE802.3x, IEEE802.3af, IEEE802.3at, IEEE802.3az
Network Media (Cable)
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e cable (≤100m)

1000BASE-X: MMF or SMF SFP module
LED
PWR, PoE, LINK/ACT, Speed
MAC Address Table
8K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T/X: 1488095pps/Port
Switching Capacity
7.2G
8.8G
Packet forwarding rate
5.4Mpps
6.5Mpps
Packet buffer
4M bit
Dimensions (L*W*H)
440*207*44 mm
Fan
Fan x 2
Power Input
AC: 100~240V, 50/60Hz
PoE Port
Port 1 to 16
Port 1 to 24
PoE Power on RJ45
Mode A 1/2(+),3/6(-)
PoE Power Output Voltage: 55V DC
Power: 32W(Max)
PoE Power budget
370W
250W
Temperature Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F)
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F)
Humidity Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing
MTBF
>50000 hours

This is a Class A product. In home environment, this product may cause radio interference. In this
case, the user may be required to take appropriate measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping
content. If the Declaration of Conformity is missing, you can request it by post under the below
mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany