Dimplex DCTFTC108 User manual

OWNER’S MANUAL
Tower Fan
MODEL: DCTFTC108
Version 1.0 2016
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the IM are for reference only.

1. If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
2. Indoor use only.
3. To protect against the risk of electrical shock, do not immerse the unit, cord
or plug in water or any other liquid.
4. This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have supervision or instruction concerning
the use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be done by children without supervision. Young children should be
supervised to ensure that they do not play with the appliance.
5. Unplug the appliance from the outlet when it is not in use or before cleaning.
6. When the fan is assembled, the rotor blade guard should not be taken off
again.
7. Correct Disposal of this product
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, aplease
use the return and collection systems or contact the retailer where the
product was purchased.
1
Read Rules for Instructions and Safe Operationscarefully.
CAUTION
WARNING
1. Never insert fingers, pencils, or any other object through the grille
when fan is running.
2. Disconnect fan when moving from one location to another.
3. Be sure fan is on a stable surface when operating to avoid
overturning.
4. DO NOT use fan in window, rain may create electrical hazard.
5. Household use only.
RULES FOR SAFE OPERATION

2
INSTALLATION INSTRUCTIONS
Name of components
Base
Body
Display window
Control panel
Align the column in the middle of the
pedestal with the hole and turn to fit

3
Turn the arrows of the two rotary knobs about 90°
Assemble the pedestal and body.
Align the three screws with corresponding hole
locations and screw tightly.

4
Press a key on the unit to activate a corresponding function.
For instance:
1. Press “+” or “-” Key to adjust 6 speeds of air flow.
(Note: Sleeping winds and natural winds function only can adjust 3
speeds of air flow.)
2. Press “ ”Key, through the "+", "-" to adjust time:
3. When the fan is on, press the “ ” key to time the fan to shut down
after 0.5-12 hours.
4. In stand-by mode, you can pre-set the fan to start in 0.5-12 hours.
5. Press “ ”Key to switch between Normal, Natural and Sleep
Functions.
6. Press “ ”Key：Press this key after activating the fan to toggle the
operation between Swing and Fixed Direction.
Display window
Timer
Normal wind
Swing
Natural wind
Sleep wind
Control panel
TIMER
MODE
SPEED/TIMER
OSC
ON/OFF
Instructions for operation of body

5
OPERATING INSTRUCTION
Remote Control
KEY INSTRUCTION
” ON/OFF KEY
1. “
The “
” key is for switching on the fan .The fan will
start in normal wind mode.
Press the “ ”key if the fan needs to be switched off.
2. “ ” SPEED KEY
When the fan has started, press this key repeatedly, the fan will
work with “1-2-3” circulatory.
3. “ ” TIMER KEY
Press this timer key repeatedly to set the time for air delivery.
Increase in increments up to "1-2-3……12" hours.
4. “ ” OSC KEY
After the fan has started, press this key to select oscillation mode.
The lights on the display will indicate fan oscillation mode.
5. “ ” MODE KEY
Press this key to select mode. The sequence for modes is normal,
natural and sleep when this key is repeatedly pressed. The light will
indicate mode state.

6
BATTERIES
(battery not included in the packing)
1. Slide the battery compartment Cover.
2. Insert the batteries, and make sure that
the batteries are placed as shown in the
right.
3. Slide back the battery cover.
NOTES: Use size “AAA” manganese or
alkaline batteries. Do not use
rechargeable batteries.
BATTERY WARNING AS BELOW
1. Do not dispose of batteries in fire, batteries
may explode or leak.
2. Do not mix old and new batteries.
3. Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
REMOTE CONTROLLER OPERATION
Point the remote controller at the receptor on the body of the fan and
press the desired button. The remote controller will work at distances of
up to roughly five meters and an angle of 30 degrees included between
the right and left from the receptor. The batteries must be removed from
the remote controller before it is scrapped and disposed of safely.
OVERHEAT PROTECTION OF THE MOTOR
The windings of the motor have a thermal-fuse that burns out and
switches the fan off if the motor overheats. Temperature of the motor will
no longer go up so that the plastic parts of the fan aren't subjected to
deformation or be burned by the overheating motor from any unexpected
reason.

7
CLEANING
1. Be sure to unplug from the electrical supply source before
cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with
mild soap. Thoroughly remove soap film with dry cloth.
DISPOSAL：Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities. Contact you
local government for information regarding the collection systems
available. If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the groundwater and get into
the food chain, damaging your health and well-being.
Rated voltage: 220-240V~ 50Hz
Rated power: 45W
Protection class: II
The fan requires little maintenance. Do not try to fix it by yourself.
Refer it to qualified service personnel if service is needed.
1. Before cleaning and assembling the fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear
of the motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild
detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the
surface.
5. Do not use any of the following as a cleaner: gasoline, thinner,
bending.
6. Do not allow water or any other liquid into the motor housing or interior
parts.
MAINTENANCE INSTRUCTION