Dimplex CFS60E User manual

08/82609/0 ISSUE: 5
INSTRUCTION MANUAL
Installation and Operating
CFSE Commercial Fan Heater
Model: CFS60E
This product is supplied and operated with a Wireless Remote Control handset

IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR
FUTURE REFERENCE. Note also the information presented on the appliance
IMPORTANT SAFETY ADVICE
DO NOT COVER OR OBSTRUCT the air inlet or outlet grille.
IMPORTANT – Disconnect from the mains supply before carrying out maintenance
work.
THIS APPLIANCE MUST BE EARTHED
This heater must not be located immediately above or below a fixed socket outlet
or connection box.
Keep combustible materials such as drapes and other furnishings clear from the front,
sides and rear of the heater.
DO NOT use this heater in the immediate surrounding of a bath, a shower or a
swimming pool.
DO NOT use this heater in areas where excessive dust exists.
DO NOT store or use any flammable materials or sprays in the vicinity of the appliance
– FIRE HAZARD.
DO NOT insert any foreign objects into the appliance openings. Risk of injury, electric
shock or damage to the appliance may occur.
This product should be mounted safely to a solid wall.
Ensure the supply cables are of adequate current carrying capacity and are protected
by a suitable fuse.
This appliance should only be connected to the fixed wiring of the premises by means
of conduit.
This product must not be subjected to water spray or immersion.
If the appliance is mounted in a toilet or washroom, the appliance should be mounted
such that no part of it can be touched by a person using a fixed bath or shower.
If the appliance is mounted in a toilet or washroom an isolating switch must be
provided outside the washroom adjacent to the entrance door.
2

DO NOT use heater to dry your laundry.
DO NOT operate the heater with the mains lead overhanging the front outlet grille.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/o the appliance
provided that it has been placed or installed in its intended normal operating position
and they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate and clean the appliance or perform user
maintenance.
CAUTION — Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are present.
The instruction leaflet belongs to the appliance and must be kept in a safe place. If
changing owners, the leaflet must be surrendered to the new owner. Ensure proper
manual handling procedures are observed at all times.
CAUTION – In order to avoid a hazard due to inadvertent resetting of the thermal
cut-out, this appliance MUST NOT be supplied through an external switching device,
such as a timer, or connected to a circuit that is regularly switched on and o by the
utility.
WARNING -Do not use this heater in small rooms where they are occupied by persons
not capable of leaving the room on their own, unless constant supervision is provided.
WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN
• Swallowing may lead to serious injury in as little as 2 hours or death, due to
chemical burns and potential perforation of the oesophagus.
• If you suspect your child has swallowed or inserted a battery go straight to a
hospital emergency room.
• Examine devices and make sure the battery compartment is correctly
secured, i.e. that the battery cover is fitted securely. Do not use if the
compartment is not secure.
• Dispose of used batteries immediately and safely. Flat batteries can still be
dangerous.
3

Model Identifier(s): CFS60E
Nominal heat output Pnom 6.0 kW
Height (mm) 360
Width (mm) 386
Depth (mm) 630
Minimum heat
output (indicative) Pmin N.A.
Maximum continuous heat output Pmax,c 6.0
Auxiliary electricity Consumption
At nominal heat output elmax 0.00
At minimum heat output elmin 0.00
In standby mode elSB <0.0005
This product meets the Ecodesign requirements for an electric fixed local space
heater Commission Regulation (EU) 2015/1188.
Energy Related Product Directive
Technical Details
Type of heat output/ room temperature control
Electronic room temperature control plus week timer Yes
With open window detection No
With adaptive start control Yes
Customer Helpline: 0344 879 3588
[e-mail]
www.dimplex.co.uk
Glen Dimplex Heating and Ventilation
Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF
4

All Models
Controls
Digitally controlled, Electronic Thermostat
Timer modes:
7 Day Programmable User Timer
Continuous heat modes:
Manual, Runback, Fan Only, O
Controller UI O-board control only. Requires pairing with Wireless remote.
Controller Functions
• Heat Selection: High, Low, Fan Only
• Adaptive-Start
• Advance time period
• Adjustable SP range (7-30°C)
• Wireless for control
Construction Steel case with plastic mouldings
Fan Type Centrifugal
Element Finned metal sheathed
Installation Supplied with wall mounting bracket
Safety Manual reset cut-out (114°C)
Automatic cut-out (86°C)
Battery Backup
None. Time and date must be re-programmed in event of power loss to
the product
Supply
Requires: 3 core for fused spur installation, 1/N/PE ~230-240 V, 50Hz
Class I, with earth wire
Colour / Finish Trac White (RAL 9016) with black grille and bracket
Approvals UKCA & CE
IP Rating IPX4
Guarantee 2 years
Country of Origin British Isles
Manufacturer Glen Dimplex Heating & Ventilation (Glen Dimplex UK Limited.)
5

b
Fig. 1 Fig. 2
Fig. 3
Fig. 4 Fig. 5
L
H
500 mm
Min.
500 mm
Min.
1000 mm
Min. 1000 mm
Min.
D2
D1
2.1 m MIN
45° Max
70 mm
70 mm
12
3a. 3b.
1
yx
2
3
a
6

General
A robust, durable wall mounting fan heater designed to coordinate with the Dimplex
range of Air Curtains, providing environmental heating in commercial and light
industrial environments.
The heater works by gradually raising the air temperature in the building and should
be positioned so as best to achieve an even temperature distribution. The product
has an output of 6kW
Wall Mounting
Remove the wall mounting bracket from the back of the heater and using it as a
guide (see Fig. 2) mark o the hole positions on a suitable wall (a minimum height
of 2.1 metres is required from the floor level to the bottom of the bracket). Solid
brick or concrete block walls must be drilled and plugged. Fix the wall mounting
bracket to the wall and assemble the heater to the extension tube using a bolt and
wing nut fitted into hole 1 shown in Fig. 3a. Rotate the heater as shown in Fig. 3b,
and fix the heater into position using the remaining bolt and wing nut in hole 2. Pivot
and rotate the heater into the desired position and tighten all three wing nuts. A
6mm Allen key can be used as an aid to tightening the bolts.
Model
Heat
Output
(kW)
Electrical Sup-
ply
Electrical Load
(per phase)
(A)
Weight (kg) Min installed
Height (M)
CFS60E 3 / 6 16.5 2.1220-240V ~1PN 26.0
Electrical Connections
The installation of this appliance should be carried out by a competent electrician
and be in accordance with the current IEE wiring regulations.
Only cable with a minimum CSA (cross sectional area) of 4.0mm must be used on
this appliance.
Electrical power and control connections are made by removing the control housing.
The control housing (‘Y’ in Fig 4) is detached by removing the two screws and
hinging the housing as shown (see step 1 in Fig 4). The bottom panel (‘x’ in Fig 4) is
detached by removing two screws and lifting o as shown (see steps 2 & 3 in Fig. 4).
NOTE:
A suitable local isolating switch must be provided in the electrical
supply circuit as close as possible to the heater with at least 3mm
clearance on each pole
Feed appropriate supply cable (see ‘a’ in Fig 5) to terminal blocks ‘c’. Make electrical
connections as shown in Fig 7 and fix cable in back panel using cable gland.
7

Thermal Safety Cut-Out
The power supply to the heating elements will be interrupted if one or a
combination of the following abnormal events occurs:
1. Air inlet grilles are obstructed.
2. Internal ventilation is impaired due to build up of dust and flu.
3. Blower unit stalls.
To reset the thermal safety cut-out, access reset button by removing the panel
shown in Fig 6 and push the reset tab in direction of arrow.
Fig. 6
8

Wiring Diagram
Fig. 7
9

The product is supplied with a Wireless remote control, the remote control should be con-
tained in the carrier bag along with these instructions. This remote control is required to
operate the appliance. When paired with the remote control various operational modes
and features can be accessed.
IMPORTANT NOTE:
The remote control is required to operate the appliance. It is important
that the remote control remains near the appliance at all times.
Remote Control
1Display Screen
2‘Menu’ Button
3‘Back’ Button
4‘Advance’ Button
5‘Up and Down’ Arrows
6‘Enter’ Button
1
3
6
2
4
5
10