Dimplex DHCER20WIFI User manual

2kW Ceramic Heater
with Wi-Fi
Model: DHCER20WIFI
INSTRUCTION MANUAL
PLEASE READ THE INSTRUCTION MANUAL CAREFULLY BEFORE USING THE UNIT

TABLE OF CONTENTS
WARNINGS AND PRECAUTIONS.......................................................1
STRUCTURE ...................................................................................3
OPERATION....................................................................................4
CLEANING AND MAINTENANCE .......................................................10
TECHNICAL REFERENCE DATA ........................................................12
WARRANTY ....................................................................................12

WARNINGS AND PRECAUTIONS
Warnings
Never place the unit near gas appliances, flames or
flammable liquids.
Never hit or shake the unit. Doing so may cause damage.
Never cover or obstruct the air inlet or outlet.
Doing so may cause overheating.
Never spray water on or place the unit near water.
Doing so may cause electric shock.
Never connect other appliances to the same power outlet.
Never connect or disconnect the power plug with wet hands.
Doing so may cause electric shock.
Never insert fingers or objects through the guards when the unit
is operating.
Never use an extension cord.
Always have a professional technician, manufacturer or service agent
replace a damaged power cord.
Precautions
This appliance is for indoor use only.
Do not use the unit near windows or where water collects. Rain and
water collection may lead to a risk of fire or electric shock.
Do not place the unit in a damp place or where humidity is high
(such as a bathroom).
Do not leave the unit operating while unattended.
Do not place the unit in direct sunlight to avoid surface
discolouration.

This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure they do not play with the
appliance.
Avoid electromagnetic interference. Keep the unit at least 1 metre
away from electric appliances such as televisions and radios.
Avoid scratching and damaging the surface. Do not use chemical
solvents (i.e. Benzene, alcohol) to clean the surface.
Place the unit on a stable surface when operating.
Unplug the unit before cleaning, servicing or maintenance.
Electrical connections must be in accordance with National or
Local Codes.
The rear of the unit must be at least 50cm away from the wall.
Do not place the appliance on its side, back or front while in storage
or transport. The unit must be left in an upright position 2 hours
before operation.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
WARNING: do not cover the heater. This may cause the unit to
overheat.
Do not use the heater in the immediate surroundings of bathtubs,
showers, washing stands or swimming pools.
The heater must not be located immediately below a socket‐outlet.

STRUCTURE
1. Buttons
2. Eco button
3. Display panel
4. Front cover
5. Front grille
6. Oscillating base
7. Base
8. Wi-Fi button
9. Back grille
10. On/Off switch
11. Power cord

OPERATION
DISPLAY PANEL
Power indicator
Temperature indicator
ECO function indicator
Timer indicator
Wi-Fi indicator
Swing indicator
Low power indicator
High power indicator

CONTROL PANEL
REMOTE CONTROL
ON/OFF button
Timer/Temperature button
Low / High Power button
Timer/Temperature set button
ECO button
Swing button

ON / OFF
This button is used to switch the unit ON and OFF.
TIMER
A timer can be set so the unit turns off automatically after a set period.
When Pressing the TIMER button once, the ‘h’ indicator will illuminate. Press
the ‘+/-’button to set the timer between 0-12 hours. Each press of the ‘+/-’
button increases/decreases the set time in 1 hour increments. If a time isn’t
set within 5 seconds, the unit will exit the timer function and revert to
displaying the room temperature.
LOW / HIGH POWER
By simply pressing this button, you can regulate the mode from LOW Power
to HIGH Power depending on your needs. The unit automatically starts in
LOW Power mode.
SWING
The unit will begin to oscillate after pressing the SWING button, the indicator
light will illuminate. To turn off the SWING function, press the swing button
again, and the swing will stop and the indicator light will switch off.
ECO MODE
When ECO Mode is selected, the unit will automatically adjust to suitable
settings according to the room temperature. When the room temperature is
below 18°C, the unit will operate in HIGH Power, and when the room is
above 18°C, the machine will operate in LOW Power. When the room
reaches 22°C the unit will stop working, until the room temperature
decreases, and will resume working again.

WI-FI
You can operate the unit wirelessly when connected to Wi-Fi. You’ll need a
Wi-Fi connection, and mobile device with the Dimplex CONNECT IT app
installed.
1. Connect mobile device to Wi-Fi and download the Dimplex CONNECT
IT app from the App Store, or Google Play.
2. Once installed, launch the app.
3. Press and hold the Wi-Fi button at the back of the unit (8) until the
Wi-Fi indicator light flashes rapidly
4. Click ‘Add the new device’. The SSID should automatically pick up
the Wi-Fi connection name.
5. Enter the Wi-Fi password ‘123456’ and hit connect.
6. Once connected you can control the unit via your mobile device and
with a 3G or 4G network connection.

You can update the device name & password by following the steps below:
*If you need to change Wi-Fi networks, press the Wi-Fi button at the back of
the unit (8), which will restore to factory settings. Then follow the steps
above to connect to a new network.
Step 1
Step 2
Step 3
Step 4
The connected
device appears in the
home screen. You
can change the
model name &
update the password
from this screen.
For Android –press
& hold the model
number to edit.
For iPhone –swipe
left on the model
until you see the
above change.
Rename the above
fields to desired
name / password
and submit.
The new device
name will appear in
the top left hand
corner in the control
panel screen.